• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.7
• /
• pp.903-909
• /
• 2014

As a direct drive type washing machine requires two operating modes, washing and spinning modes, a design of the motor with high efficiency in each mode is not applicable to a conventional procedure. To achieve the requirements, a multi-pole outer rotor type switched reluctance motors are considered. To select a suitable motor type for the application, a static toque is compared based on the FEM analysis. The selected type is obtained for high and wide toque than other types of the motor. Further, the pole shape and arc are optimized to meet the required torque and torque ripple. To verify the proposed structure, the prototype is designed and manufactured. And the simulation and experimental results verify the validity of the proposed structure.

• Proceedings of the KIEE Conference
• /
• 2004.10a
• /
• pp.126-128
• /
• 2004

This paper deals with an automatic optimum design based on capacity for a synchronous reluctance motor (SynRM). The focus of this paper is the design relative to the output power on the basis of rotor shape of a SynRM in each capacity. And optimization algorithm is used by means of sequential unconstrained minimization technique(SUMT). The coupled Finite Elements Analysis (FEA) & Preisach model have been used to evaluate nonlinear solutions. The proposed procedure allows to define the rotor geometric dimensions according to capacity starting from an existing motor or a preliminary design.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.7 no.2
• /
• pp.153-160
• /
• 1983

The flows in an axial flow turbomachine are calculated numerically in the two sets of flow surfaces of H-S and B-B surfaces assuming that the flow is axisymmetric. The calculation is performed by regarding the governing equations as the quasi-Poisson's equations and using the finite element method for the flow regions divided into triangular elements. The results of numerical calculation agree comparatively well with the experimental results and it has been found that the distribution of an axial velocity component at the rotor exit is not necessarily uniform under the influences of the inlet guide vanes and the front shape of the hub even if the rotor is designed by the free-vortex theory. Also it has been found that the existence of the optimum value of the blade number can be estimated from the results of calculation of deviation angles at rotor exit if we consider the viscous flow-loss, and that the flows of B-B surfaces are affected very sensitively by the degree of satisfaction of Kutta condition.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.6
• /
• pp.2187-2193
• /
• 2014

In this paper, we propose a method for suppressing shaft voltage by modifying the rotor shape and the permanent magnets in interior permanent magnet type high voltage motors. The shaft voltage, which adversely affects the bearing by occurring bearing current, is induced by parasitic components and the leakage flux in motor-driven systems as well as inherent linkage flux between main magnetic flux and shaft according to rotor configuration. Thus, shaft voltage should be analyzed and considered under inverter-driven and non-inverter-driven conditions because inherent linkage flux can analyze under non-inverter-driven condition. In this study, we designed re-arrangement magnet and re-structuring rotor to minimize the shaft voltage. In addition, we optimized the proposed models. The shaft voltage suppression effect of the designed model was validated experimentally and by comparative finite element analysis.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.52 no.2
• /
• pp.39-52
• /
• 2003

This paper deals with an automatic design procedure for the maximum torque density and power factor in a synchronous reluctance motor (SynRM). The focus of this paper is the design relative to the number of flux barrier and the ratio Kw of flux barrier width to iron sheet width of a SynRM under the mechanical constraint. The Finite Elements Analysis (FEA) has been used to evaluate the maximum torque density and power factor with each rotor shape. The proposed procedure allows to define the rotor geometric dimensions starling from an existing mootor or a preliminary design. The maximum torque density and power factor of a SynRM has been resulted with the rotor design variation. To prove the propriety of the designed SynRM, the Digital Signal Processor (DSP) installed experimental devices are equipped and the efficiency characteristic test is Performed.

• Journal of Magnetics
• /
• v.19 no.4
• /
• pp.404-410
• /
• 2014

This paper considers the design and performance evaluation of interior permanent magnet synchronous motors (IPMSMs). The initial design such as the sizing and shape design of the stator and rotor is performed for a given load condition. In particular, the equivalent magnetic circuit (EMC) is employed both to design the mechanical parameters of the rotor while considering nonlinear magnetic saturation effect and to analyze the magnetic characteristics of the air-gap of the motor. The designed motor is manufactured and tested to confirm the validity of the design processes and simulated results.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.672-675
• /
• 1997

This paper presents the identification of rotor dynamic parameters. The solution of the system equation can be obtained using least square method. The sensitivity analysis is performed to extract optimized solution, which is considered to be insensitive to inherent measurement errors. The cosine and sine term of orbit shapes can be obtained by experiment the orbit analysis at a different speed after doing orbit analysis at an arbitrary selected speed. This values measured time domain used to search the stiffness and damping coefficients of rotor bearing.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.696-697
• /
• 2015

In this paper, the shape of the slit to provide a view of the sensor in such a manner as to encode the rotor position information using a single sensor for studies of economic rotor position and speed detection method for electric motor drive has a special electronic commutator bar-and proposes a robust encoder can produce a rotor position information for each of the woman, and reads out the location information by using the position detection method of the proposed new method compared to traditional DSP Capture function of incremental encoder that its validity was verified through experiments.

• Proceedings of the KIEE Conference
• /
• 2001.04a
• /
• pp.404-406
• /
• 2001

This paper is about designing the magnetizing system which is used for magnetizing the NdFeB magnet in a squirrel cage rotor. It propose the shape of the magnetizing yoke, the number of coil turn and the capacitor discharging circuit parameter. In case of magnetizing the NdFeB magnet assembled with a squirrel cage rotor, the eddy current which is produced during magnetizing becomes a disturbance in magnetizing NdFeB magnet. Hence in this paper, we try to design optimized magnetizing system with eddy current considered by FEM(Finite Element Method).

• Proceedings of the KIEE Conference
• /
• 2005.04a
• /
• pp.114-116
• /
• 2005

This paper deals with an automatic design standard computation based on a rated watt for a synchronous reluctance motor (SynRM). The focus of this paper is mating the design relative to the output rover on the basis of rotor shape of a SynRM in each rated watt using a coupled FEM & sequential unconstrained minimization technique (SUMT). The coupled finite elements analysis (FEA) & Preisach model have been used to evaluate nonlinear solutions. The proposed procedure allows to define the rotor geometric dimensions according to the rotor diameter and rated watt starting from an existing motor or a preliminary design.