• 한국인쇄학회지
• /
• 제24권2호
• /
• pp.11-24
• /
• 2006

The Lithographic ink is composed of pigment, vehicle and additives. In especially, the vehicle is the most important element and consist of vegetable oils, mineral oils and resins. Varnishes have to resist certain forms of chemical and physical attack during ink manufacturing process and printing process So this varnish cooking is very important. In this paper, effects of cooking conditions of varnish using phenolic modified rosin ester on physical properties of the vehicle were studied. The varnish cooked according to temperature and time were compared in order of average molecular weight by the GPC method. and the rheological properties were found by rotational rheometer. And the emulsion behavior were compared by high speed emulsification tester which were set on 1200 rpm and $40^{\circ}C$ temperature (Novomatics Lithotronic). We displayed viscosity against tack(Inkometer Thwing-Albert M-106) by diagram.

• Journal of Electrochemical Science and Technology
• /
• 제8권1호
• /
• pp.1-6
• /
• 2017

The conductivity of the electrolyte used plays a critical role in the optimization of the performance of electrochemical double layer capacitors. However, when the difference in the conductivities of different electrolytes is not significant (only 10-20%), the conductivity has little effect on the capacitance. On the other, unlike the conductivity and viscosity of the electrolyte, the cation size directly influences the capacitance. Cyclic ions have a smaller effective radius than that of the corresponding acyclic ions because the acyclic alkyl groups have a greater number of conformational degrees of freedom, such as the rotational, bending, and stretching modes. Consequently, because of the smaller effective size of the cyclic ions, cells containing electrolytes with such ions exhibit higher capacitances than do those with their acyclic counterparts.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2007년도 7th International Meeting on Information Display 제7권1호
• /
• pp.200-202
• /
• 2007

Improvement of LC mixtures can be realized by the development of new molecules in combination with the identification of advanced mixture concepts. By new high-polar single materials rotational viscosity has recently been improved significantly. Now, a new LC mixture concept for IPS and FFS technology has been identified which additionally improves switching time by up to 10%. This advanced concept is based on a more efficient usage of high-polar materials and Super Low Viscous (SLV) compounds and simultaneous reduction of less efficient materials.

• Journal of the Korean Society for Industrial and Applied Mathematics
• /
• 제16권3호
• /
• pp.181-192
• /
• 2012

Here in this paper, the steady paint film flow on a vertical wall of a non-Newtonian pseudo plastic fluid for drainage problem has been investigated. The exact solution of the nonlinear problem is obtained for the velocity profile. Also the average velocity, volume flux, shear stress on the wall, force to hold the wall in position and normal stress difference have been derived. We retrieve Newtonian case, when material constant ${\mu}_1$ and relaxation time ${\lambda}_1$ equal zero. The results for co-rotational Maxwell fluid is also obtained by taking material constant ${\mu}_1$ = 0. The effect of the zero shear viscosity ${\eta}_0$, the material constant ${\mu}_1$, the relaxation time ${\lambda}_1$ and gravitational force on the velocity profile for drainage problem are discussed and plotted.

• 한국산학기술학회논문지
• /
• 제20권12호
• /
• pp.513-518
• /
• 2019

마찰교반용접(Friction Stir Welding) 기술은 금속 소재를 대상으로 하는 용접기술 중의 하나로 용접대상이 되는 소재와 고속으로 회전하는 용접툴 사이의 마찰로 인한 열을 활용하여 소재의 융점 이하 온도에서 접합하는 기술이다. 이번 연구에서는 마찰교반용접을 진행할 때, 용접 대상물의 내부 온도 변화를 분석하기 위한 방법으로 수치해석기법을 사용하였다. 용접소재로는 마그네슘 합금인 AZ31을 고려하였으며, 용접현상을 멜팅풀(melting-pool)이 생성되는 유동특성으로 간주하고 유동해석을 수행하기 위해 유동특성 수치해석 툴인 FLUENT를 이용하였다. 용접과정의 유동해석을 진행하기 위해 용접소재는 고점도 뉴턴 유체로 가정하였고, 용접툴과 용접대상 소재의 경계면은 마찰 및 미끄러짐이 동시에 발생하는 조건으로 경계조건을 선정하였다. 그리고 용접툴의 회전속도 및 용접속도를 변수로 하여 다양한 해석을 진행하였다. 해석 결과로부터 용접툴의 회전속도가 높을수록, 용접속도가 느릴수록 소재 내 최고온도가 증가함을 확인할 수 있었으며, 그 중 용접툴의 회전속도 차이가 온도 변화에 더 큰 영향을 보임을 확인하였다.

• 한국식품과학회지
• /
• 제21권6호
• /
• pp.815-819
• /
• 1989

밤전분 현탁액(3% 및 4%)의 유동특성을 모세관 점도계로 분석하였을 때 $30-65^{\circ}C$에서 항복응력이 존재하지 않는 딜라탄트유체의 거동을 보였다. 그러나 3% 전분 현탁액은 $70^{\circ}C$에서, 4% 전분현탁\액은 $65^{\circ}C$ 이상에서 의가소성 유체의 거동을 보였다. 밤전분 현탁액의 점조도지수의 활성화에너지는 $50^{\circ}C$이하에서는 0.56kcal/mole, $60-70^{\circ}C$에서는 51.9-80.8 kcal/mole 이었다. 전분 호화액(4%)의 유동특성을 회전점도계로 측정하였을 때 가열온도 및 시간에 관계없이 겉보기 점도는 지수적으로 감소하여 의가소성을 나타내었다. 밤전분 호화액을$65-80^{\circ}C$로 가열했을 때의 겉보기 점도의 대수값은 동일온도에서의 전분의 팽화력과 밀접한 관계를 보였다. 가열온도 $70-80^{\circ}C$에서의 겉보기 점도의 활성화 에너지 값은 13.9kcal/mole이었다. 상압$(90^{\circ}C)$ 및 가압$(121^{\circ}C)$ 호화액은 측정온도의 증가에 따라 겉보기 점도가 감소하였으나, 가압호화액은 측정온도의 증가에 따라 겉보기 점도가 감소하였으나, 가압호화액의 겉보기 점도는 동일온도에서 상압호화액의 겉보기 점도보다 높은 값을 보였다.

• 유변학
• /
• 제11권1호
• /
• pp.57-65
• /
• 1999

분말사출재의 항복응력을 효과적이고 간단한 방법으로 측정하기 위해서 수차 장치를 사용한 항복응력 측정장치를 개발하였다. 수차 방식은 벽면 미끄러짐을 고려할 필요가 없는 장점이 있으나 전단률에 따른 점도 변화 측정에는 사용할 수 없는 단점도 있다. 수차 장치의 타당성 검토를 선형유체를 사용하여 검증하였으며, 수차 장치의 양단에서 나타나는 오차도 실험적으로 확인하였다. 분말 현탁액의 일반적인 특징이라고 여겨지는 항복 시 발생하는 순간 최대 토오크는 측정 장치의 제어기 특성에 따른 영향이 큰 것을 확인하고 안정 토오크 영역을 항복응력 계산의 기준으로 결정하였다. 측정되는 토오크에서 수차의 회전 저항에 따른 효과를 제거하기 위해 다양한 속도에서 측정된 토오크를 선형함수로 근사하여 회전 속도가 없을 때의 토오크를 얻었다. 측정 방법의 일반적인 검증을 위해 텅스텐 카바이드 분말과 왁스계 바인더를 이용한 분말사출재의 항복응력을 온도와 분말 충전률 변화에 따라서 측정하였다.

• Tribology and Lubricants
• /
• 제33권6호
• /
• pp.269-274
• /
• 2017

Currently, fuel efficiency becomes one of critical issues for automotive industries as concerns about environmental and energy problems grow. In an automatic transmission of an automobile, a drag torque due to a viscous drag of a fluid between friction and clutch plates is one of factors that degrade fuel economy. In this work, the drag torque characteristics of a wet clutch was experimentally investigated with respect to rotational speed, temperature of automatic transmission fluid (ATF), and gap between friction and clutch plates. The experimental results showed that drag torque increases to a certain level, and then decrease to the steady state value with increasing rotational speed. This behavior may be associated with two-phase flow of air and ATF at gap between friction and clutch plates. Also, it was found that the maximum drag torque value decreased as ATF viscosity decreases with increasing temperature. However, it was shown that the point at which the maximum drag torque occurs was not significantly affected by the ATF temperature. In addition, maximum drag torque was found to decrease as the gap between friction and clutch plates increased from 0.1 mm to 0.2 mm. Furthermore, it was observed that the generation of maximum drag torque was delayed as the gap increased. The outcomes of this work are expected to be helpful to gain a better understanding of drag torque characteristic of a wet clutch, and may therefore be useful in the design of wet clutch systems with improved performance.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2004년도 Asia Display / IMID 04
• /
• pp.843-846
• /
• 2004

For the fast growing Liquid Crystal Display (LCD) TV market, it is essential to make the LCD panels to show moving images without any visual difficulties such as blurring or tailing. Owing to reduction of the cell gap and the improved Liquid Crystal (LC) mixtures with low viscosity, it is possible that our S-IPS TFT-LCDs feature a response time (R/T) as fast as 1-frame time (16ms) for a white-black operation and less than a 16rns in all gray levels without Over Driving Circuit (ODC) technology. Currently, mass production of the large size IPS panels with high speed has been successfully achieved. In order to achieve faster response time, new LC mixtures have been developed, optimizing the physical properties of rotational viscosity (${\gamma}$1) and elastic constants (Kii). Also, the LC mixtures with high elastic constant allow us to increase the cell gap. In this paper, realization of fast switching time in IPS mode with optimized '${\gamma}$1/Kii' parameter in the LC mixtures forms the core of this paper.

• 한국염색가공학회지
• /
• 제22권3호
• /
• pp.187-193
• /
• 2010

The effects of molecular weight (MW) and concentration on the rheological properties of poly(vinyl alcohol) (PVA) solutions in dimethyl sulfoxide (DMSO) were investigated at $30^{\circ}C$. Ubbelohde viscometer and rotational rheometer were employed for dilute and concentrated regime, respectively. In the dilute regime, the Mark-Houwink exponent ($\alpha$) of the solutions determined from three different MWs proved 0.73. The critical concentration (C*), in which the entanglement and overlap of polymer molecules began to take place, decreased with increasing the MW of PVA. Huggins constant ($K_H$) values ranged from 0.33 to 0.45 over the MW examined. In the log-log plot of $\eta_{sp}$ versus [$\eta$]C, the PVA with higher degree of polymerization (DP) gave a greater slope exhibiting the inflection point in the vicinity of C*. In the dynamic viscosity ($\eta'$) curve, the PVA solutions of DP 1700 presented Newtonian fluid behavior over most of the frequency range examined. However, the lower Newtonian flow region reduced with increasing the DP. As the PVA concentration increased, $\eta'$ was increased and the onset shear rate for pseudoplasticity was decreased. In the Cole-Cole plot, PVA solutions showed almost a single master curve in a slope of ca. 1.65 regardless of the DP. However, the increase of the concentration from 8 to 12 wt% for PVA solutions of DP 5000 decreased the slope from 1.73 to 1.57. In the tan $\delta$ curve, the onset frequency for sol-gel transition was shifted from 154 to 92 rad/s with increasing the DP from 3300 to 5000 and from 192 to 46 rad/s with increasing the concentration from 8 to 12 wt%. In addition, longer relaxation time ($\lambda$) was observed with increasing the DP and concentration.