• 전기학회논문지
• /
• 제62권7호
• /
• pp.1045-1052
• /
• 2013

In this study we deal with design procedures for the flywheel energy storage system that has the capacity to store the regenerative energy produced from the railway vehicles. The flywheel energy storage system (FESS) stores the regenerative electrical energy into the high speed rotational flywheel, by conversion the electrical energy into the mechanical rotational energy. Thus the FESS is composed of the energy conversion components, such as the motor and generator, mechanical support components, such as the rotational rotor, the magnetic bearings to support the rotor, and the digital controller to control the air gap between the rotor and the magnetic bearings. In this paper the design procedures for the rotor operating at the rigid mode and the magnetic bearings to support the rotational rotor without contact are presented.

• 한국자동차공학회논문집
• /
• 제8권2호
• /
• pp.110-119
• /
• 2000

In this study, we considered the method evaluation the flexibility of joint area including member with circular section. We regarded the flexibility of joint area as translational and rotational springs for the purpose of expressing local deformation. We verified this method by the use of normal mode analysis. We also calculated this joint area occurring in penetration so as to apply this method to other cases. Compare with the shell element model. we can the considerably approximate values.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 추계학술대회 논문집 Vol.17
• /
• pp.563-566
• /
• 2004

We have studied a electrically controlled birefringence (ECB) mode for field sequential liquid crystal display (FSLCD). We measured response time of the ECB mode. The ECB mode exhibiting fast response time, high transmittance, low operating voltage and adequate viewing angle. The positive liquid crystal (LC) is better than negative LC on dielectric anisotropy, birefringence and rotational viscosity. So that, the ECB mode is one of strongest candidate for FSLCD application.

• 소음진동
• /
• 제6권1호
• /
• pp.97-106
• /
• 1996

This paper presents systematic study of the experimental application of a free-interfaced component mode synthesis method. In the free-interfaced component mode synthesis method, an error the to truncated higher modes and neglected ineria loadings on a component from the connected component is inherent. Also, it is difficult to directly use experimental modal data in a modal synthesis method which links experimental model to finite-element model because of many inconsistencies between experimentally obtained and analytically obtained modal vectors and missing degrees-of-freedom (DOFs) such as rotational DOFs. In order to solve these problems, three methods, the first one based on attaching auxiliary weights to the connection points, the second one utillizing the normalization of experimental modal vector, and the third one generating smoothed and expanded experimental mode shapes, are studied in this paper. Finally, the study is illustrated for a flat-plate structure by using simulated and measured experimental data.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1997년도 추계학술대회논문집; 한국과학기술회관; 6 Nov. 1997
• /
• pp.43-49
• /
• 1997

A rotating rigid disk, attached on a flexible shaft or supported by a torsional spring, experiences precessional whirling due to gyroscopic moment loading. It is well known in rotor dynamics area that, as the rotational speed increases, the precessional mode of the rotating rigid disk starts splitting into two: forward and backward precessional modes. On the other hand, it is also well known in disk vibration area that a rotating flexible disk also shows another kind of mode splitting phenomenon due to the rotation, resulting in forward and backward traveling waves. When rotating multiple flexible disks are coupled in vibration with the supporting Flexible shaft, the associated mode splitting should be compatible with the two seemingly different vibration analysis methods. This paper investigates the possibility of fusing the precessional and traveling wave mode splittings so that the bending coupled disk vibrations in HDD spindle systems can be better understood.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2009년도 추계학술대회 논문집
• /
• pp.413-414
• /
• 2009

• Smart Structures and Systems
• /
• 제13권5호
• /
• pp.731-753
• /
• 2014

In this study, an indirect approach is developed for assessing the state of a bridge on the basis of mode shapes estimated by the responses of passing vehicles. Two types of damages, i.e., immobilization of a support and decrease in beam stiffness at the center, are evaluated with varying degrees of road roughness and measurement noise. The assessment theory's feasibility is verified through numerical simulations of interactive vibration between a two-dimensional beam and passing vehicles modeled simply as sprung mass. It is determined that the damage state can be recognized by the estimated mode shapes when the beam incurs severe damage, such as immobilization of rotational support, and the responses contain no noise. However, the developed theory has low robustness against noise. Therefore, numerous measurements are needed for damage identification when the measurement is contaminated with noise.

• Structural Engineering and Mechanics
• /
• 제29권5호
• /
• pp.531-550
• /
• 2008

This paper adopts the numerical assembly method (NAM) to determine the exact solutions of natural frequencies and mode shapes of a multi-span and multi-step beam carrying a number of various concentrated elements including point masses, rotary inertias, linear springs, rotational springs and springmass systems. First, the coefficient matrix for an intermediate station with various concentrated elements, cross-section change and/or pinned support and the ones for the left-end and right-end supports of a beam are derived. Next, the overall coefficient matrix for the entire beam is obtained using the numerical assembly technique of the conventional finite element method (FEM). Finally, the exact solutions for the natural frequencies of the vibrating system are determined by equating the determinant of the last overall coefficient matrix to zero and the associated mode shapes are obtained by substituting the corresponding values of integration constants into the associated eigenfunctions.

• Structural Engineering and Mechanics
• /
• 제5권6호
• /
• pp.715-728
• /
• 1997

The aim of this paper is to investigate the secondary buckling behaviour and mode-coupling of spherical caps under uniformly external pressure. The analysis makes use of a rotational finite shell element on the basis of strain-displacement relations according to Koiter's shell theory (Small Finite Deflections). The post-buckling behaviours after a bifurcation point are analyzed precisely by considering multi-mode coupling between several higher order harmonic wave numbers: and on the way of post-buckling path the positive definiteness of incremental stiffness matrix of uncoupled modes is examined step by step. The secondary buckling point that has zero eigen-value of incremental stiffness matrix and the corresponding secondary mode are obtained, moreover, the secondary post-buckling path is traced.

• Geomechanics and Engineering
• /
• 제13권4호
• /
• pp.653-669
• /
• 2017

By increase in the population and consequently constructions, new structures may be built in vicinity of the soil slopes. Such structures can be regarded as an extra surcharge on the slopes. The intensity and location of the surcharge affects the displacements of the slopes. Few researchers have studied the effect of surcharge on displacements of soil slopes. In this research, using limit analysis method and upper bound theory with non-associated flow rule, displacements of soil slopes in vicinity of a surcharge has been estimated. The authors have improved the technique previously proposed by them and a new formulation is suggested for calculating the permanent displacements of the soil slope in presence of a surcharge for two failure modes, rotational and transitional. A comparison has also been made between the two mentioned modes for various conditions of surcharge and slope. The conditions resulting in the rotational mode to be more critical than the transitional mode have been investigated. Also, the effects of surcharge's intensity, location of surcharge as well as the soil properties have been investigated.