• 한국자동차공학회논문집
• /
• 제9권6호
• /
• pp.65-75
• /
• 2001

Modern vehicles require a high degree of refinement including good driveability. Vehicle driveability, which becomes a key decisive factor f3r marketability, is affected by many parameters such as engine control and the dynamic characteristics in drive lines. Therefore engine and drive train characteristics should be considered to achieve a well balanced vehicle response simultaneously. This paper describes experimental procedures which have been developed to measure engine torque and investigate shuffle characteristics. To analyze the vehicle dynamic behavior, fractional torques and inertia mass moment of engine, and drive train were measured. Shuffle characteristics during tip-in condition were investigated in an experimental vehicle at 2nd and 3rd gear stages. It was found that the shuffle characteristics were caused by sudden changes of engine torque and have a different vibration frequency with gear stage variation. Inertia mass moment of engine including flywheel rotation showed a key factor for the shuffle characteristics.

• 한국항공운항학회지
• /
• 제19권3호
• /
• pp.16-24
• /
• 2011

In this research, a cockpit display system using 3 dimensional geographic information was developed. A coordinate transformation method from WGS84 to TM was first studied. Octree data structure was used for efficient 2D and 3D graphic display. Also, a 3D graphic engine was developed for fast display with large amount of geographic data which can be practically used in aircraft onboard computer having low performance. This 3D engine contains additional function such as geographic and object information loading, many kinds of camera mode, aircraft position and rotation control function, character strip display. In the future research, actual GPS signal should be used and additional information that can help pilot's decision should be display.

• 한국소음진동공학회논문집
• /
• 제19권12호
• /
• pp.1281-1288
• /
• 2009

Variation of dynamic characteristics of a low pressure turbine blade with crack length is studied in this paper via both experiments and finite element model. Since most of the turbine blades used in domestic power plants are imported from abroad, it is necessary to understand their dynamic behavior in advance. When experimentally obtained natural frequencies and mode shapes are compared with those from FEM results, they are close to each other in their magnitude. Then, it is more feasible to use finite element model for analyzing the dynamic characteristics of a blade under various operation conditions (rotation speed, temperature, etc) as well as with a crack in the blade.

• 한국소음진동공학회논문집
• /
• 제22권2호
• /
• pp.163-169
• /
• 2012

The brake squeal propensity associated with friction curve is investigated by using the hybrid finite element(FE)-analytical model. The modal analysis of an actual disc and pad is conducted by FE method. Also, the modeling for the accurate contact and disc rotation is analytically achieved. The eigenvalue analysis for the hybrid model provided the squeal dependency on the friction curve. Particularly, some pad modes and the disc torsion mode are shown to be sensitive for the friction curve.

• Steel and Composite Structures
• /
• 제1권1호
• /
• pp.33-50
• /
• 2001

In this paper an experimental study is performed on end-plate type joints. The test arrangement represents a column-base joint of a steel frame. Altogether six specimens were tested, each of them subjected to cyclic loading. The specimens were carefully designed by performing detailed preliminary calculations so that they would present typical behaviour types of end-plate joints. On the basis of the experimentally established moment-rotation relationship, the cyclic characteristics of each specimen have been calculated and compared to one another. The results are evaluated, qualitative and quantitative conclusions are drawn.

• Structural Engineering and Mechanics
• /
• 제5권1호
• /
• pp.85-104
• /
• 1997

The paper investigates the influence of lateral restraint on the buckling behaviour of plate under non-uniform compression. The unloaded edges are assumed to be partially restrained against translation in the plane of the plate and the distributions of the resulting forces acting on the plate are shown. The stability analysis is done numerically using the Galerkin method and various strategies the economize the numerical implementation are presented. Results are obtained showing the variation of the buckling load, from free edge translation to fully restrained, with unloaded edges simply supported, clamped and partially restrained against rotation for various plate aspect ratios and stress gradient coefficients. An apparent decrease in the buckling load is observed due to these destabilizing forces acting in the plate and changes in the buckling modes are observed by increasing the intensity of the lateral restraint. A comparison is made between the budding loads predicted from various formulas in stability standards based on free edge translation and the values derived from the present investigation. A difference of about 34% in the predicted buckling load and different buckling mode were found.

• 한국지반환경공학회 논문집
• /
• 제14권9호
• /
• pp.39-47
• /
• 2013

Local deformations in back filling materials of two sands and one glass bead with different particle shapes behind a rigid retaining wall were studied. Two kinds of boundary conditions were compared: active wall translation and active rotation of the wall about its toe. Effect of the speed of active wall translation was also investigated. The digital image correlation method was used to analyze local deformation developments inside the materials. Test results showed that particle shape and density mainly influence the inclination angle and width of the shear band. The general shear band pattern is strongly dependent on the wall movement mode, while it was little influenced by particle shape. Within a limited range of wall speed in this study, shear band became wider and local deformation became larger with increase of wall speed.

• Journal of information and communication convergence engineering
• /
• 제8권4호
• /
• pp.433-436
• /
• 2010

In this paper, we presented a ciphering method whose target data is any kind of digital bit-stream. It uses a chaotic system as the main encrypting tool, MISR (Multi-Input Signature Register), and shift-and-rotation function, all of which are exclusive-ORed with the plaintext. Also, it incorporates a cipher text feedback mode such that part of the previously ciphered data is fed back to encrypt the current data. The encryption block size and the amount of feedback data are different at each ciphering operation. Experimental results with the image/video date showed that this method has enough speed and encryption effect with negligible latency time. Thus, we are expecting it to have various application areas that need high speed stream ciphering with high security level.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2007년도 7th International Meeting on Information Display 제7권1호
• /
• pp.710-712
• /
• 2007

The effects of stress on the IZO/PC substrate and the electro-optical properties of a flexible LCD with microstructure in bending were investigated. It showed that the IZO/PC substrate and the periodic cross spacers are good enough to be employed in the application of the ECB or polarization rotation LC mode.

• Structural Engineering and Mechanics
• /
• 제56권5호
• /
• pp.835-854
• /
• 2015

In this paper, the modified form of shear deformation plate theories is proposed. First, the displacement field geometry of classical and the first order shear deformation theories are compared with each other. Using this comparison shows that there is a kinematic relation among independent variables of the first order shear deformation theory. So, the modified forms of rotation functions in shear deformation theories are proposed. Governing equations for rectangular and circular thick laminated plates, having been analyzed numerically so far, are solved by method of separation of variables. Natural frequencies and mode shapes of the plate are determined. The results of the present method are compared with those of previously published papers with good agreement obtained. Efficiency, simplicity and excellent results of this method are extensible to a wide range of similar problems. Accurate solution for governing equations of thick composite plates has been made possible for the first time.