• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11a
• /
• pp.304-311
• /
• 2001

This research numerically analyzes the dynamic characteristics of a coupled journal and thrust hydrodynamic bearing due to its groove location which has the static load due to the weight of a rotor in the axial direction and the dynamic load due to its mass unbalance in the radial direction. The Reynolds equation is transformed to solve a plain member rotating type of journal bearing(PMRJ), a grooved member rotating type of journal bearing (GMRJ), a plain member rotating type of thrust bearing (PMRT) and a grooved member rotating type of thrust bearing (GMRT). FEM is used to solve the Reynolds equations in order to calculate the pressure distribution in a fluid film. Reaction forces and friction torque are obtained by integrating the pressure and shear stress along the fluid film, respectively. Dynamic behaviors, such as whirl radius or floating height of a rotor, are determined by solving its nonlinear equations of motion with the Runge-Kutta method. This research shows that the groove location affects the pressure distribution in the fluid film and consequently the dynamic performance of a HDD spindle system.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.2
• /
• pp.156-163
• /
• 2001

The experiment is conducted on the rapidly rotating incompressible flow within a confined cylinder using LDV(Laser Doppler Velocimetry). The configurations of interest are the flows between a rotating upper disk with a bar and a stationary lower disk enclosed within a cylinder. The flow is considered to be an axisymmetric undisturbed basic flow. The results show that the flow is strongly dependent on the radius and the shape of bar but is negligibly affected by the Reynolds number in turbulent flow. It is observed that in the lid-driven case the main forms near the wall as the Reynolds number increases. The thin bar causes the second axial flow due to the suction effect and the thick bar causes the main flow to be pulled toward the surface of the bar. The step bar shows the dual effect of the two. 1:2 tilt bar shows that the main flow distributes wider than the other cases in which interference occurs due step bar.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.166-174
• /
• 2002

This paper presents an analytical method to Investigate the stability of a hydrodynamic journal bearing with rotating herringbone grooves. The dynamic coefficients of the hydrodynamic journal bearing are calculated using the FEM and the perturbation method. The linear equations of motion can be represented as a parametrically excited system because the dynamic coefficients have time-varying components due to the rotating grooves, even in the steady state. Their solution can be assumed as a Fourier series expansion so that the equations of motion can be rewritten as simultaneous algebraic equations with respect to the Fourier coefficients. Then, stability can be determined by solving Hill's infinite determinant of these algebraic equations. The validity of this research is proved by the comparison of the stability chart with the time response of the whirl radius obtained from the equations of motion. This research shows that the instability of the hydrodynamic journal bearing with rotating herringbone grooves increases with increasing eccentricity and with decreasing groove number, which play the major roles in increasing the average and variation of stiffness coefficients, respectively. It also shows that a high rotational speed is another source of instability by increasing the stiffness coefficients without changing the damping coefficients.

• Advances in concrete construction
• /
• v.13 no.5
• /
• pp.367-376
• /
• 2022

Theoretical study of vibration distinctiveness of rotating cylindrical are examined for three volume fraction laws viz.: polynomial, exponential and trigonometric. These laws control functionally graded material composition in the shell radius direction. Functionally graded materials are controlled from two or more materials. In practice functionally graded material comprised of two constituent materials is used to form a cylindrical shell. For the current shell problem stainless steel and nickel are used for the shell structure. A functionally graded cylindrical shell is sanctioned into two types by interchanging order of constituent materials from inner and outer side for Type I and Type II cylindrical shell arrangement. Fabric composition of a functionally graded material in a shell thickness direction is controlled by volume fraction law. Variation of power law exponent brings change in frequency values. Influence of this physical change is investigated to evade future complications. This procedure is capable to cater any boundary condition by changing the axial wave number. But for simplicity, numerical results have been evaluated for clamped- simply supported rotating cylindrical shells. It has been observed from these results that shell frequency is bifurcated into two parts: one is related to the backward wave and other with forward wave. It is concluded that the value of backward frequency is some bit higher than that forward frequency. Influence of volume fraction laws have been examined on shell frequencies. Backward and forward frequency curves for a volume fraction law are upper than those related to two other volume fraction laws. The results generated furnish the evidence regarding applicability of present shell model and also verified by earlier published literature.

• Journal of Biosystems Engineering
• /
• v.21 no.2
• /
• pp.134-145
• /
• 1996

Since the skid-steer loader is able to work for excavating, lifting and transporting load even at the narrow space, they are widely used in the regular farm and the livestock farm. The skid-steer loader normally adopts the hydrostatic transmission because the power to move the machine backward and forward should be delivered independently on both sides of wheels. Contrast to the mechanical system such as chain and belt transmissions, however, the hydrostatic transmission is less efficient in the use of energy and more difficult in the maintenance. This study was intended to investigate the feasibility of using triangular-type belt clutch and V-belt transmission for the newly developed skid-steer loader in order to overcome the problems stated in the hydrostatic transmission. In the developed triangular-type belt clutch, the centers of driving, driven and idler sheaves are arranged in the triangular shape in a plane, and V-belts were loaded loosely on three sheaves. The power is transmitted by pressing the idler connected to a lever on the loosened V-belt. Contrast to the normal belt clutch using two sheaves, the newly developed belt clutch has the characteristics of small contact-angle of the driving sheave at no bucket load and increasing contact-angle at the time of power transmission. The results of research can be summarized as follows: 1) The developed triangular-type belt clutch adopted a spring-loaded slackside idler which could transmit more power than a fixed idler could by sacrificing the belt life. The life of V-belt used in the power transmission reached at 500 hours(6 months) when the engine power of 11.8 ㎾ was transmitted. Also, it was feasible to develop the large industrial skid-loader with the V-belt transmission by using the proper set of sheaves. 2) The developed skid-steer loader changed the rotating radius and speed with bucket loads as the conventional skid steer loader did. The rotating speed was 47 deg/s at the maximum bucket load of 2.74 kN when the minimum rotating radius was 1.5m. 3) The power required in turning at the bucket load of 2.74 kN was 4 ㎾ and the slippage of V-belt was less than 1%.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.5
• /
• pp.197-212
• /
• 1997

The performance of a torque converter can be expressed by the performance parameters such as flow radius and flow angle, on the mean flow path. The geometric analysis of the torque converter is required to determine these parameters for the modeling of the torque converter. In general, the blade shape is depicted by three dimensional data at the mid-surface of blade or those of the pressure and suction side. To generate three dimensional model of the blade using the data mentioned above, a consistent data format and a shape generation algorithm are required. This paper presents a useful consistent data format of the blades and an algorithm for the geometrical shape generation. By the geometric analysis program to which the shape generation algorithm is embedded, the variation of blade angles in rotating element analyzed. Then finally, the analyzed results of geometric profile of a blade are compared with those of the blade design principle, so called forced vortex theorem.

• The Bulletin of The Korean Astronomical Society
• /
• v.35 no.1
• /
• pp.72.2-72.2
• /
• 2010

We use three-dimensional hydrodynamic simulations to investigate nonlinear gravitational responses of gas to, and the resulting drag force on, a massive perturber moving on a circular orbit through a uniform gaseous medium. We assume that the background medium is non-rotating and adiabatic with index 5/3, and represent the perturber using a Plummer potential with softening radius a. This work extends our previous study where we showed that the drag force on a straight-line trajectory is proportional to a0.45 if the perturber is massive enough. This indicates that the orbital decay of supermassive black holes (SMBHs) near galaxy centers may take much longer than the prediction of the linear force formula applicable for low-mass perturbers. For the circular orbits are considered, however, we find that the nonlinear drag force becomes independent of a, but dependent instead on the orbital radius R as $\varpropto$ R0.5. This suggests not only that the choices of large values of a, for resolution issues, in recent numerical experiments for mergers of SMBH, are marginally acceptable, but also that the gaseous drag indeed provides an efficient mean for the orbtial decay of SMBHs.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.3183-3186
• /
• 2007

Taylor-Couette flow may appear when the angular velocity is different between two concentric rotating cylinders. This kind of Taylor-vortex flow can be easily seen in lots of engineering problems. In general the geometries of rotating cylinders are generally complex in these cases. In this study, we investigated Taylor-Couette flow when the outer cylinder has the slit along the annulus. The radius ratio and aspect ratio of the experimental model used was 0.825 and 48, respectively. The depth of slits is 5mm and total 18 slits are azimuthally located along the inner wall of outer cylinder. We used PIV method to measure the flow and applied index matching method to resolve the complex geometry effect. The results show the model with slit has no stable wavy vortex region above Re=143.

• Journal of Welding and Joining
• /
• v.14 no.5
• /
• pp.78-86
• /
• 1996

Vision sensor was used to track the weld line of the compressor case. The compressor case was fixed in jig equipped with the rotating system, and two torches having one degree of freedom was applied in automatic welding system. The radius of rotation for the compressor case is varying with each rotating angle, while, the angle velocity is constant Therefore, an algorithm to extract the feature of the compressor case for varying rotation angle is needed. To over come the avove difficulties, the curve fitting and composite curve were used. The experiment to verify the proposed algorithm showed desirable results for tracking the welding line of compressor case.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.29 no.10 s.241
• /
• pp.1083-1091
• /
• 2005

Turbulent flow around a rotating circular cylinder is investigated by Direct Numerical Simulation. The calculation is performed at three cases of low Reynolds number, Re=161, 348 and 623, based on the cylinder radius and friction velocity. Statistically strong similarities with fully developed channel flow are observed. Instantaneous flow visualization reveals that the turbulence length scale typically decreases as Reynolds number increases. Some insight into the spacial characteristics in conjunction with wave number is provided by wavelet analysis. The budget of dissipation rate as well as turbulent kinetic energy is computed and particular attention is given to the comparison with plane channel flow.