• 대한조선학회논문집
• /
• 제47권4호
• /
• pp.533-542
• /
• 2010

For a long times it has been believed that the Magnus effect of the rotating cylinder could be utilized for the lifting devices applicable to marine practices. It has been reported that the rotating cylinder installed on upper deck of commercial vessel could play a energy saving role however the idea might be applicable in a very rare case in ship building practices. In this study special high lift rudder system equipped with the trailing edge rotor has been suggested in correspondence with the increasing requirement of greater rudder force. Through the numerical simulation it is cleared that the trailing edge rotor could play a role in enhancement of circulation and refinement of boundary layer of the rudder system. At the same time it is found out that the lift force of the rudder system without rotation of trailing edge rotor could be doubled when the circumferential velocity of the trailing edge rotor is equal to twice of the inflow velocity.

• 대한기계학회논문집A
• /
• 제27권11호
• /
• pp.1889-1896
• /
• 2003

In the microfluidic applications, viscous-driven pumping mechanism is a promising one since the viscous effect increases significantly as the size of device decreases, relative to the inertial effect. However, there exist a few drawbacks we have to improve such as low efficiency and small volume flow rate. In the present study, an optimum design synthesis is proposed to enhance the performance characteristics of the micropump with single rotating cylinder. First, the unstructured grid CFD method is described and validated by comparing its results to the previous results. Next, an automated optimum design synthesis tool is constructed by combining the aforementioned CFD analysis model with the mathematical optimization model. This technique is used to improve the performance characteristics of newly designed viscous-driven pump. The presented results show that the fluid dynamic optimization tool is robust and may be applied to other microfluidic device design applications.

• Design & Manufacturing
• /
• 제18권2호
• /
• pp.1-8
• /
• 2024

Unlike the roll-to-roll process that uses a steel roll and a nip roll, a vacuum roll can hold and transfer a thin film using a single roll. To precisely manufacture a vacuum roll, a thin outer cylinder must be machined, which is assembled on the outside of the roll and contacts the film via vacuum pressure. In this study, the effects of jaw width and chucking force on the deformation of the outer cylinder during the turning process were investigated using analysis, and a precision machining and burr removal process was developed. The deformation of the outer cylinder decreased almost linearly with increasing jaw width and increased with higher chucking force and larger cylinder diameter. Additionally, the deflection due to the weight of the outer cylinder was approximately three times greater than that caused by film tension. For the machined outer cylinder, a burr removal experiment was conducted, and concentricity and cylindricity were measured. Using a device that removes burrs by rotating a wheel connected to the main shaft at high speed, it was found that burrs generated on the inner diameter could be removed very efficiently. On the vacuum side, the concentricity errors of the inner and outer diameters were 0.015 mm and 0.014 mm, respectively, and on the opposite side, they were 0.006 mm and 0.010 mm, respectively. Additionally, the measurement of Total Indicator Runout (TIR) according to the angle showed that the maximum cylindricity of the outer and inner diameters was 0.02 mm and 0.025 mm, respectively. Finally, through burr-height measurement at the hole boundary, it was found that the heights were within 0.05 mm.

• 대한기계학회논문집B
• /
• 제22권5호
• /
• pp.640-650
• /
• 1998

Pumping performances of a helical molecular drag dump(MDP) and of a radial MDPs are numerically analyzed by using the direct simulation Monte Carlo (DSMC) method. A helical- and radial-MDP have rotating pumping channels cut on a cylinder and on a disk, respectively. For a helical MDP, the present results agree quantitatively with the previously known numerical results. For radial MDPs, both of the Type 1 (having pumping channels cut on the stationary disk) and of the Type 2 (having pumping channels cut on the rotating disk) are analyzed to predict their performances for various parameters, i.e., the radius of curvature center of the channel wall, the depth of the channel, the clearance between housing and disk, and the rotating speed. The results show that the performance of the Type 2 is superior to that of the Type 1, and that for all types the pumping efficiency decreases as the clearance increases. Also, the radial type MDP has larger leakage losses in the direction of pumping channel than does the helical one.

• Steel and Composite Structures
• /
• 제38권2호
• /
• pp.189-211
• /
• 2021

An analytical solution is presented to analyze the thermoelastoplastic response of a rotating thick-walled cylindrical pressure vessel made of functionally graded material (FGM). The analysis is based on Tresca's yield condition, its associated flow rule and linear strain hardening material behaviour. The uncoupled theory of thermoelasticity is used, and the plane strain condition is assumed. The material properties except for Poisson's ratio, are assumed to vary nonlinearly in the radial direction. Elastic, partially plastic, fully plastic, and residual stress states are investigated. The heat conduction equation for the one-dimensional problem in cylindrical coordinates is used to obtain temperature distribution in the vessel. It is assumed that the inner surface is exposed to an airstream and that the outer surface is exposed to a uniform heat flux. Tresca's yield criterion and its associated flow rule are used to formulate six different plastic regions for a linearly hardening condition. All these stages are studied in detail. It is shown that the thermoelastoplastic stress response of a rotating FGM pressure vessel is affected significantly by the nonhomogeneity of the material and temperature gradient. The results are validated with those of other researchers for appropriate values of the system parameters and excellent agreement is observed.

• 대한기계학회논문집
• /
• 제16권3호
• /
• pp.540-546
• /
• 1992

본 연구에서는 레이놀즈응력 모델이 곡률효과에 대한 추가적인 수정을 요구하 는 지를 알기 위하여 유선곡률에 의해 영향을 받는 원형 쿠에트 유동에 대해 수치계산 을 수행하고, 이 결과를 측정한 실험치와 비교하였다. 본 연구의 실험에서는 완전 난류 영역에서 난류평균속도와 난류응력성분들을 측정하였다. 수치계산에 있어서는 레이놀즈응력 모델에 대하여 Gibson과 Younis가 곡률효과를 고려해 제안한 새로운 모 델상수를 기존의 모델상수와 함께 적용하여 그 결과를 비교하였다. 계산된 결과를 본 실험의 측정치와 아울러 함께 Smith와 Townsend의 측정치와도 비교하였다.

• 한국소음진동공학회논문집
• /
• 제12권9호
• /
• pp.717-724
• /
• 2002

In this study, a numerical analysis for the piston secondary dynamics of small refrigeration reciprocating compressors is performed. In general, the length of cylinder in this class of compressors is shortened to diminish the frictional losses of the piston-cylinder system. So, the contacting length between piston and cylinder wall is in variable with the rotating crank angle around the BDC of the reciprocating piston. In the problem formulation of the piston dynamics, the change in bearing length of the piston and all corresponding forces and moments are considered in order to determine the piston trajectory, velocity and acceleration at each step. A Newton-Raphson procedure was employed in solving the secondary dynamic equations of the piston. The developed computer program can be used to calculate the entire piston trajectory and the hydrodynamic force and moment as functions of crank angle under compressor running conditions. The results explored the effects of the radial clearance, lubricant viscosity, length of the cylinder wall, and pin location on the stability of the piston.

• 인지과학
• /
• 제14권4호
• /
• pp.9-19
• /
• 2003

Bonneh, Cooperman 과 sagi (2001)[1] 는 역치이상의 강도를 갖는 정지자극이 운동자극과 섞여서 제시될 때 정지자극이 의식에서 간헐적으로 소멸함을 보고하면서 이 현상을 MIB (motion-induced-blindness)라고 명명하였다. 본 연구에서는 흰색 점으로 구성된 회전하는 원통체와 함께 제시되는 녹색 정지 점들을 오른쪽 눈에 적색 필터를 착용하고 관찰할 경우에 녹색 정지 점들이 의식에서 간헐적으로 소멸함을 보여주었다. 본 연구에서 관찰되는 MIB 현상은 원통체가 회전할 때에 그리고 한 쪽 눈에 적색 필터를 착용할 때에만 나타난다. 또한 녹색 점의 명도대비와 원통체를 구성하는 흰색 점의 명도대비가 감소할수록 녹색 정지점이 의식에서 소멸하는 시간이 감소하였으며, 정지자극과 운동자극을 구성하는 점의 수가 감소할수록 정지자극이 의식에서 소멸하는 시간이 감소하였다. 흥미롭게도 정지자극과 운동자극의 상대적인 깊이가 정지자극이 소멸하는 시간에 영향을 미쳤다. 이러한 실험결과는 본 연구에서 보고하는 MIB 현상이 Bonneh 등이 보고한 MIB 현상과 구별되며, 양안경쟁으로는 이 현상이 설명할 수 없고, 시각 정보처리에서 후기단계의 정보처리가 이 현상에 관여함을 시사한다.

• Journal of Welding and Joining
• /
• 제19권3호
• /
• pp.334-341
• /
• 2001

The chemical and geometric effects of weld on flow-accelerated corrosion (FAC) of SA106 Gr.C low alloy steel pipe in 3.5wt% NaCl and simulated feedwater of nuclear power plant have been investigated by using rotating cylinder electrode. Polarization test and weight loss test were conducted and compared at rotating speed of 2000rpm (3.14m/s) with the variables of chemical and geometric parameters. The results showed that the chemical effects were relatively larger than the geometric effects, and the welded parts were the local anode and preferentially corroded, which could be explained by the differences between microstructural and compositional parameters. On the other hand, under active corrosion conditions, the heat affected zone were severely corroded and microstructural effects became the important role in the whole process.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2009년도 9th International Meeting on Information Display
• /
• pp.510-512
• /
• 2009

A volumetric 3D display system based on a rotating two dimensional color LED array is set up. It has a cylinder display space ${\Phi}800{\times}640mm3$ which is composed of 256 slices of pictures in one 3D image with each slice $320{\times}256$ LED pixels. The volumetric image has 4 gray scales and 64 colors. The main structure and working principle of the system is described in detail.