• Korean Journal of Materials Research
• /
• v.30 no.5
• /
• pp.246-251
• /
• 2020

The annealing characteristics of cold-rolled Al-6.5Mg-1.5Zn-0.5Fe-0.5Mn alloy, newly designed as an automobile material, are investigated in detail, and compared with those of other aluminum alloys. Using multi-pass rolling at room temperature, the ingot aluminum alloy is cut to a thickness of 4 mm, width of 30 mm, and length of 100 mm to reduce the thickness to 1 mm (r = 75 %). Annealing after rolling is performed at various temperatures ranging from 200 to 500 ℃ for 1 hour. The specimens annealed at temperatures up to 300 ℃ show a deformation structure; however, from 350 ℃ they have a recrystallization structure consisting of almost equiaxed grains. The hardness distribution in the thickness direction of the annealed specimens is homogeneous at all annealing temperatures, and their average hardness decreases with increasing annealing temperature. The tensile strength of the as-rolled specimen shows a high value of 496 MPa; however, this value decreases with increasing annealing temperature and becomes 338 MPa after annealing at 400 ℃. These mechanical properties of the specimens are compared with those of other aluminum alloys, including commercial 5xxx system alloys.

• Korean Journal of Agricultural Science
• /
• v.46 no.1
• /
• pp.45-56
• /
• 2019

As a result of analyzing the quality of imported grapes during the 2018 season, the hardness of the grape berry was found to be 10 N or less in total. In the case of Chilean grapes, the soluble solids tended to be lower as imports and distribution periods were delayed. The berry weight was the largest at 14.4 - 14.8 g for the 'Red Globe', 7.1 - 7.4 g for the 'Thompson Seedless' and 6.0 - 7.0 g for the 'Crimson Seedless'. The 'Crimson Seedless' grapes imported from Chile, which had a high berry shatter rate, had a shorter pedicel length, pad width and brush length than that of the other 2 varieties. Regardless of the grape varieties, the weight loss during the distribution at room temperature ($25^{\circ}C$) increased rapidly as the import season was delayed. Additionally, it was found that the later the distribution seasons, a higher stem browning index was observed regardless of the variety. The 'Thompson Seedless' was revealed to be more susceptible to browning than that of the other varieties. The shrinkage of the stem and the pedicel browning progressed within a short time during shelf-life as the distribution time was delayed. The incidence of berry decay of the imported grapes tended to increase with the progression of the distribution period. In the fruits distributed on April, except for the 'Crimson Seedless', the grapes were rapidly corrupted in the second half of the distribution. The 'Red Globe' grapes completely lost marketability due to a berry decay of 26.1% and 69.9% at 9 and 12 days after shelf-life, respectively.

• Journal of the Korean Magnetics Society
• /
• v.9 no.1
• /
• pp.23-28
• /
• 1999

${\Alpha}-Fe_2O_3$ was accomplished by chemical method as low temperature as possible and the crystallographic and magnetic properties have been studied by Mossbauer spectroscopy and X-ray diffraction. The sample heated at 15$0^{\circ}C$ is found to have a Corundums symmetry with the hexagonal lattice constant a=8.26$\pm$0.05$\AA$, c=8.75$\pm$0.05$\AA$. The M$\"{o}$ssbauer spectra between the 4.2K and the room temperature show that the ${\Alpha}-Fe_2O_3$ crystallized with a single phase and fine sizes. The particle size distribution has the Gaussian distribution center at 98$\AA$ and the half width of 32$\AA$.TEX>.

• Journal of Convergence for Information Technology
• /
• v.10 no.2
• /
• pp.82-88
• /
• 2020

The purpose of this study is to obtain basic data on the optimization of firing process conditions for enamel coating in chemical heat exchanger. The method of increasing the firing temperature in order to apply enamel coating to shell & tube type heat exchanger was examined. The temperature distribution of the heat exchanger in the firing kiln was numerically calculated using a commercial CFD program. The structural safety of the heat exchanger was confirmed by thermal stress analysis using the FSI method. Numerical analysis and experimental results show that there is a problem of safety due to temperature difference when the heat exchanger at room temperature is directly put into a firing kiln at 860℃. Therefore, a preheating process is need to reduce the temperature difference. As in Case2 with fewer firing steps, the first stage preheating temperature of 445℃and the second stage firing temperature of 860 ℃are considered to be most suitable.

• The Korean Journal of Pesticide Science
• /
• v.19 no.3
• /
• pp.295-300
• /
• 2015

Currently, amount of export strawberry has been continuously increased to ship many south Asia countries, including Hong Kong and Singapore. In the distribution process, significant damage to the quality has been caused depending on the environmental conditions. Gray mold disease caused by Botrytis cinerea has been known as major damage to the export strawberry, and the disease was caused during shipping and distribution to the final consumers. This study was performed to assess the relationship between pathogen density in packing shed and disease incidence of gray mold during storage period. Maximum gray mold disease incidence in storage period was up to 16% with low temperature condition ($4^{\circ}C$). At room temperature condition, the disease incidence reached up to 100% even densities of the pathogen spore were recorded relatively low in the packing shed. As results of the study, the correlation between pathogen density in the air and disease occurrence clearly clarified.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.10
• /
• pp.1541-1550
• /
• 1997

Since the ceramic/metal joint material is made at a high temperature, the residual stress develops when it is cooled from bonding temperature to room temperature due to remarkable difference of thermal expansion coefficient between ceramic and metal. As residual stress at ceramic/metal joints influences the strength of joints, it is important to estimate residual stress quantitatively. In this study, it is attempted to estimate joint residual stress of Si$_3$N$_4$STS304 joints quantitatively and to compare the strength of joints. The difference of residual stress is measured when repeated thermal cycl is loaded, under the conditions of the practical use of the ceramic/metal joint. The residual stress increases at 1 cycle of thermal load but decreases in 3 cycles to 10 cycles of thermal load. And 4-point bending test is performed to examine the influence of residual stress on fracture strength. As a result, it is known that the stress of joint decreases as the number of thermal cycle increases.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.22 no.7
• /
• pp.826-832
• /
• 1998

In order to understand the influences of wearing clothings with different thermal insula-tions when men were exposed from $25^{\circ}C$ environment to 18$^{\circ}C$ environment, thermoregulatory responses were measured on 4 healthy female college students. Subjects rested wearing T-shirts, trousers, and socks called LC(total weight 541g) at 25$\pm$1$^{\circ}C$, 50$\pm$5% R.H. and then exposed to the room conditioned in 18$\pm$1$^{\circ}C$, 50$\pm$5$^{\circ}C$ R.H. with LC as it was(LC Type) or with T-shirts, trousers, socks, training wear upper garment, the training wear lower garment called HC (total weight 1368g)(HC Type) for 120 min. The results can be summarized as follows: 1) When subjects were exposed from $25^{\circ}C$ environment to 18$^{\circ}C$ environment, decrease of rectal temperature was significantly smaller in LC Type than in HC Type. 2)Increase of heat production and weight loss had no significant difference between two types of clothing. 3)Internal thermal conductance was higher in HC Type and external thermal conductance was higher in LC Type. Therefore total thermal conductance was higher in LC Type than in HC Type. 4)Decrease of skin temperature was greater in LC Type than in HC Type. 5)Subjects felt colder with LC Type than with HC Type, but did not feel differently in comfort sensation between two types of clothing. It was suggested that less decrease of rectal temperature in LC type inspite of more dry heat loss from body might be ascribed to a shift of blood from the shell area to the core area originating in the vasoconstriction and the lowered internal thermal conductance. In conclu-sion, the importance of the state of internal heat distribution in the homeostasis seemed to be reaffirmed.

• Progress in Superconductivity
• /
• v.4 no.1
• /
• pp.86-89
• /
• 2002

In this paper, the design of a IMVA single-phase high temperature superconducting(HTS) power transformer with BSCCO-2223 HTS tapes is presented. The rated voltages of each sides of the transformer are 22.9 ㎸ and 6.6 ㎸, respectively The winding of 1MVA HTS transformer is consisted of double pancake type HTS windings, which have advantages of insulation and distribution of high voltage, and are cooled by subcooled liquid nitrogen of 65K. Four HTS tapes were wound in parallel for the windings of low voltage side and the four parallel conductors are transposed. The design of 1MVA HTS transformer, a shell type core made of laminated silicon steel plate is chosen, and the core is separated with the windings by a cryostat with a room temperature bore. The cryostat made of non-magnetic and non-conducting material and a liquid nitrogen sub-cooling system is designed in order to maintain the coolant's temperature of 65K. For electromagnetic analysis of 1MVA HTS transformer, a finite element method of an axis of symmetry is used. The maximum perpendicular component of magnetic flux density of pancake windings is about 0.15T. And through analyzing the magnetic field distribution, an optimal winding arrangement of 1MVA HTS transformer is obtained.

• FLOWER RESEARCH JOURNAL
• /
• v.19 no.4
• /
• pp.212-218
• /
• 2011

Edible flowers are harvested at the full bloom stage and distributed without floral stems, which makes the flower quality deteriorated quickly. Thereby, this study was carried out for selection of effective storage film at room temperature during the distribution of edible flowers. Edible flowers, snapdragon (Antirrhinum majus), pot-marigold (Calendula officinalis), sweet violet (Viola odorata), clove pink (Dianthus caryophyllus), wild pansy (Viola tricolor), nasturtium (Tropaeolum majus) were used to select the effective storage film at room temperature during the distribution, polyethylene (PE) film (0.03 mm), polypropylene (PP) film (0.03 mm). PP (LF10) film packing was very effective for longer shelf life for sweet violet, clove pink, and wild pansy. But, there were little different for pot-marigold and nasturtium. Wilting at sweet violet, clove pink, and wild pansy, and petal-soft rot and color break at nasturtium were appeared. Browning and rot were appeared to snapdragon.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.342-343
• /
• 2009

Paper factories use a large amount of water and same amount of wastewater is generated. It is important to purity and recycle the wastewater because of water shortages and water pollution. The existing water treatment facilities like precipitation process need large-scale equipment and wide space to purity the wastewater of paper factory. High gradient magnetic separation (HGMS) system has the merits to purity rapidly because of large voids at filter and to occupy small space. In this paper, two types of superconducting magnets were used for HGMS systems. Cryo-cooled Bi-2223 superconducting magnet system with 70 mm room temperature bore and 200 mm of height was prepared. Cryo-cooled Nb-Ti superconducting magnet with 100 mm room temperature bore and 600 mm of height was used for magnetic separator. Magnetic filters were designed by the analysis of magnetic field distribution at superconducting magnets. The various magnetic seeding reactions were investigated to increase the reactivity of coagulation. The effects of magnetic separation of wastewater were investigated as variation of magnetic field strength and flow rate of wastewater.