• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.6
• /
• pp.465-470
• /
• 2020

Heterolayered K(Ta,Nb)O₃/Pb(Zr,Ti)O₃ thin films on Pt/Ti/SiO₂/Si substrates were prepared by a sol-gel process and spin-coating method. The structural and electrical properties were measured to investigate the possibility of application as an electrocaloric effect device. All specimens exhibited dense and uniform cross-sectional structures without pores, and the average thickness of the specimen coated six times was approximately 394 nm. Curie temperatures were observed at 5℃ or less in type-I and 10℃ in type-II specimens, respectively. Type-II specimens coated 6 times showed a relative dielectric constant of 758 and remanent polarization of 9.71 μC/㎠ at room temperature. The maximum electrocaloric effect occurred between 20 and 25℃, slightly higher than their Curie temperature, and the electrocaloric property (ΔT) of the type-II specimens coated 6 times was approximately 1.2℃ at room temperature.

• Journal of Welding and Joining
• /
• v.7 no.3
• /
• pp.19-27
• /
• 1989

Both the SS41 steel and the M.E.F(martensite encapsulated islands of frrite) dual phase steel made of SS41 steel by heat treatment were welded by friction welding, and then manufactured machinemade Vnotch standard Charpy impact specimens and precracked with a fatigue system at BM(base metal), HAZ(heat affected zone) and WZ(weld interface Zone). The impact test of them was performed with an instrumented impact test machine at a number of temperatures in constant loading velocity and the dynamic fracture characteristics were studied on bases of the absorbed energy, dynamic fracture toughness and fractography from the test. The results obtained are as follows; At the room temperature, the absorbed energy is HAZ.geq.WZ.geq.BM in case of the M.E.F. dual phase steel: BM.geq.HAZ.geq.WZ in case of the SS41 steel, HAZ.geq.BM.geq.WZ at the low temperature. The absorbed energy is decreased markedly with the temperature lowering; it is highly dependent on the temperature. The dynamic fracture toughness of the M.E.F. dual phase steel is HAZ.geq.WZ.geq.BM at the room temperature; BM.geq.WZ.geq.HAZ below-60.deg. C. Therefore the reliability of friction welding is uncertain at the low temperature(below-60.deg. C). The dynamic fracture toughness of the SS41 steel; HZA.geq.WZ.geq.BM at overall temperature region. The flaw formed by rotational upsetting pressure was shown y SEM; in this region. The absorbed energy per unit area and dynamic fracture toughness were low relative to other region.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.63 no.4
• /
• pp.33-41
• /
• 2021

The emission characteristics and emission factors were determined by measuring the concentration of methane (CH₄) and nitrous oxide (N₂O), the amount of ventilation, etc. in the two fattening rooms which have the same environment in winter. As a result of monitoring, the average concentration of CH₄ and N₂O was 20.7-26.7 ppm and 1.4-1.6 ppm. The average temperature inside the room was measured at 20.0-21.4℃, and the average ventilation was 1345.4-1567.3 m³/h. The daily emission of CH₄ for the first 30 days showed a constant emission of 3.6-8.2 g/d/m²/pig, but thereafter, the emission increased rapidly. The daily emission of N₂O was 0.7-1.3 g/d/m²/pig, showing stable emission during the test period, and relatively insignificant emission compared to the emission of CH₄. After repeated test, it was confirmed that there was no significant difference between the two rooms. As a result, the CH₄ 6. 21 g/d/m²/pig and N₂O 1.02 g/d/m²/pig average emission for each room was derived.

• Steel and Composite Structures
• /
• v.38 no.1
• /
• pp.87-102
• /
• 2021

To investigate the failure form, bending stiffness, and residual bearing capacity of monolithic composite beams with laminated slab throughout the fire process, fire tests of four monolithic composite beams with laminated slab were performed under constant load and temperature increase. Different factors such as post-pouring layer thickness, lap length of the prefabricated bottom slab, and stud spacing were considered in the fire test. The test results demonstrate that, under the same fire time and external load, the post-pouring layer thickness and stud spacing are important parameters that affect the fire resistance of monolithic composite beams with laminated slab. Similarly, the post-pouring layer thickness and stud spacing are the predominant factors affecting the bending stiffness of monolithic composite beams with laminated slab after fire exposure. The failure forms of monolithic composite beams with laminated slab after the fire are approximately the same as those at room temperature. In both cases, the beams underwent bending failure. However, after exposure to the high-temperature fire, cracks appeared earlier in the monolithic composite beams with laminated slab, and both the residual bearing capacity and bending stiffness were reduced by varying degrees. In this test, the bending bearing capacity and ductility of monolithic composite beams with laminated slab after fire exposure were reduced by 23.3% and 55.4%, respectively, compared with those tested at room temperature. Calculation methods for the residual bearing capacity and bending stiffness of monolithic composite beams with laminated slab in and after the fire are proposed, which demonstrated good accuracy.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.34 no.5
• /
• pp.314-320
• /
• 2021

Controlling ambient humid condition through high performance humidity sensors has become important for various fields, including industrial process, food storage, and the preservation of historic remains. Although aerosol deposited humidity sensors using ceramic BaTiO₃ (BT) material have been widely studied because of their longtime stability, there remain critical disadvantages, such as low sensitivity, low linearity, and slow response/recovery time in case of the sensors fabricated at room temperature. To achieve superior humidity sensing properties even at room temperature condition, BT-Cu composite films utilizing aerosol deposition (AD) process have been proposed based on the percolation theory. The BT-Cu composite films showed gradually improved sensing properties until the Cu concentration reached 15 wt% in the composite film. However, the excessive Cu (above 30 wt%) containing BT-Cu composite films showed a rapid decrease of the sensing properties. The results of observed surface morphology of the AD fabricated composite films, to figure out the metal filler effect, showed correlation between surface topography as well as size and the amount of open pores according to the metal filler content. Overall, it is very important not only dielectric constant of the humidity sensing films but also microstructures, because they affect either the variation range of capacitance by ambient humidity or adsorption/desorption of ambient humidity onto/from the humidity sensing films.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.8
• /
• pp.617-621
• /
• 2010

($K_{0.5}Na_{0.5}$)($Nb_{0.96}Sb_{0.04}$)$O_3$+1.2 mol% $K_4CuNb_8O_{23}$ ceramics doped with iron oxide ($Fe_2O_3$) were prepared by a conventional mixed oxide method. And then, their piezoelectric and dielectric properties were investigated as a function of $Fe_2O_3$ addition. X-ray diffraction studies reveal that $Fe^{3+}$ diffuses into the NKN lattices to form a solid solution with a pure perovskite structure at room temperature. At the sintering temperature of $1,060^{\circ}C$, when 0.2 mol% $Fe_2O_3$ was doped, the piezoelectric constant ($d_{33}$), electromechanical coupling factor (Kp), and mechanical quality factor ($Q_m$) showed the excellent values of 131.67 pC/N, 0.436, and 696.36, respectively. Results show that $Fe_2O_3$ deped ($K_{0.5}Na_{0.5}$)($Nb_{0.96}Sb_{0.04}$)$O_3$+1.2 mol% $K_4CuNb_8O_{23}$ lead-free piezoelectric ceramics are a promising lead free material for piezoelectric transformer applications.

• Journal of the Korean Ceramic Society
• /
• v.43 no.2 s.285
• /
• pp.106-113
• /
• 2006

PMN-PZT films with thickness of $5\;{\mu}m$ were deposited on $Pt/Ti/SiO_2/Si$ substrate at room temperature using aerosol deposition process. The films showed fairly dense microstructure without any crack. XRD and TEM analysis revealed that the films consisted of randomly oriented nanocrystalline and amorphous phases. Post-annealing process was employed to induce crystallization and grain growth of the as-deposited films and to improve the electrical properties. The annealed film showed markedly improved electrical properties in comparison with as-deposited film. The film after annealing at $700^{\circ}C$ for 1h exhibited the best electrical properties. Dielectric constant $(\varepsilon_r)$, remanent polarization $(P_r)$ and piezoelectric constant $(d_{33})$ were 1050, $13\;{\mu}C/cm^2$ and 120 pC/N, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.286-289
• /
• 2001

Single phase CuGaS$_2$ thin film with the highest diffraction peak of (112) at diffraction angle (2$\theta$) of 28.8$^{\circ}$ was made at substrate temperature of 7$0^{\circ}C$, annealing temperature of 35$0^{\circ}C$ and annealing time of 60 min. And second highest (204) peak was shown at diffraction angle (2$\theta$) of 49.1$^{\circ}$. Lattice constant of a and c of that CuGaS$_2$ thin film was 5.37 $\AA$ and 10.54 $\AA$ respectively. The greatest grain size of the thin film was about 1${\mu}{\textrm}{m}$. The (112) peak of single phase of CuGaS$_2$ thin film at annealing temperature of 35$0^{\circ}C$ with excess S supply was appeared with a little higher about 10 % than that of no exces S supply And the resistivity, mobility and hole density at room temperature of p-type CuGaS$_2$ thin film with best crystalline was 1.4 $\Omega$cm, 15 cm2/V . sec and 2.9$\times$10$^{17}$ cm$^{-3}$ respectively. It was known that carrier concentration had considerable effect than mobility on variety of resistivity of the fabricated CuGaS$_2$ thin film, and the polycrystalline CuGaS$_2$ thin films were made at these conditions were all p-type.

• Journal of the Microelectronics and Packaging Society
• /
• v.17 no.2
• /
• pp.35-40
• /
• 2010

The variations of dielectric properties of $Ta_2O_5-SiO_2$ continuous composition spread thin films prepared by off-axis radio-frequency magnetron sputtering were investigated. The dielectric maps of dielectric constant and loss were plotted via 1500 micron-step measuring. The specific points showing superior dielectric properties of high dielectric constant (k~19.5) and loss (tan${\delta}$<0.05) at 1 MHz were found in area of the distance of 16 mm and 22 mm apart from $SiO_2$ side in $75{\times}25mm^2$ sized Pt/Ti/$SiO_2$/Si(100) substrates.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.8 no.2
• /
• pp.154-161
• /
• 1984

A modified technique of the transient hot wire method to measure the thermal conductivity of fluid has been described in this paper. The thermal conductivity of fluid can be obtained by acquiring wire temperature as a function of time. Multiplication of the inverse slope of the temperature versus logarithm of time by an instrumental constant gives the thermal conductivity. The constant voltage was applied to Wheatstone bridge circuit. The wire temperature can be measured as a function of time precisely with the aid of the data acquisition system composed of a microprocessor and an analog-digital converter. The thermal conductivity of the electrically conducting fluid has been measured with the insulated hot wire coated by electrically non-conducting material. The effect of the coated insulation layer on the thermal conductivity has been examined, in which it is confirmed that the thermal conductivity of electrically conducting liquid can be determined by the transient coated hot wire method. Thermal conductivities of methanol, carbontetrachrolide, Freon-22 and glycerin have been measured at room temperature in the pressure from 0.1MPa to 35.1MPa. The experiment has been performed to compare the data from the bare and the coated wires, and the results are satisfactory.