• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 한국정밀공학회 1992년도 춘계학술대회 논문집
• /
• pp.306-312
• /
• 1992

The prevention of roll breakage in hot rolling process is improtant to reduce maintenance cost and production loss. Rolling conditions such as the roll force and torque have been intensively studied to overcome the roll breakage. in the present work, a model for life prediction of work rolls under working condition was developed and discussed. The model consists of stress analysis, crack propagation, wear and fatigue calculation model. Roll life can be predicted by stress, crack depth and fatigue damage calculated from this model. The reliability of stress analysis is backed up by the FEM analysis. From the result of simulation using by pressent model, although the fatigue damage of back up roll reachs 80% of practical limit, that of workroll was less than 40%. In edge section of workroll stress amplification is found by wear and bender effect. We can judge that workroll failures are not due to fatigue damage, crack propagation by bending stress but stress amplification by wear and bender in present working condition.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 한국표면공학회 2012년도 춘계학술발표회 논문집
• /
• pp.182-183
• /
• 2012

Organic light emitting diode (OLED) 나 organic photovoltaic device (OPV)와 같은 유기소자에 전극으로 쓰이고 있는 indium tin oxide (ITO) 박막의 품질을 향상시키기 위해 수소 및 산소의 가스량을 조절하면서 rf power를 이용하여 ITO 박막을 증착한 후 전기적, 광학적 특성을 관찰하여 보았다. 또한 ITO 박막의 대면적화 및 양산화를 위하여 Roll to Roll 장비를 적용하였다. 산소 분율 0.3%에서 두께 180 nm 와 면저항 21 ohm/sq.를 나타냈으며 수소 분율 0.8%에서 두께 180 nm, 면저항 22 ohm/sq.이 관찰되었다. 또한 산소 분율 0.3%로 고정한 후 수소 분율을 변화시키며 관찰한 결과 수소분율 0.3%에서 두께 180 nm, 면저항 19 ohm/sq.를 나타내었다.

• Journal of Power System Engineering
• /
• 제16권6호
• /
• pp.52-58
• /
• 2012

Roll forming process is one of the most widely used processes in the world for forming metals such as a furniture drawer guide or an up and down slide guide. It can manufacture goods of the uniform cross section on a large scale throughout the continuous processing. In the domestic design and manufacture, roll forming process for production is taking most of the method of 2-point under rail slide. However, this method is vulnerable to the structural strength and stiffness is not suitable for high load conditions. Therefore, through systematic study of high load, low noise 3-point ball type of under rail slide its own design and manufacturing technology is the need to build. In this paper, to make center member of 3-point ball-type under rail slide for the refrigerator doors, the roll forming modeling and simulation are performed. Tensile test is performed about SCP-1 1/2H for determine the mechanical properties of materials. Modeling and simulation of roll forming is used MSC.MARC software of a dedicated analysis program used by rigid plastic finite element method. Interference between the roll and the final shape are predicted from the results of the simulation.

• Journal of Welding and Joining
• /
• 제27권3호
• /
• pp.85-91
• /
• 2009

A roll projection welding machine is introduced to fabricate metallic sandwich plate consisting of a structured inner sheet with projection-like shape and a pair of skin sheets. To fabricate the metallic sandwich plate of consistent and good quality, two process monitoring methods are introduced; dynamic resistance monitoring and skin sheet temperature monitoring. Dynamic resistance monitoring has no time delay but gives only averaged value over plate width. Skin sheet temperature monitoring has certain amount of time delay but is good for predicting weld quality of specified position. By the two complementary monitoring methods, the characteristics of the new welding process is successfully understood.

• Transactions of Materials Processing
• /
• 제25권5호
• /
• pp.319-324
• /
• 2016

Recently, the roll forming process is one of the most widely used processes for manufacturing automotive part. In this study, flower patterns of roll forming process were designed to manufacture an ultra high strength bumper beam using the finite element analysis. Three types of flower patterns such as the basic type, the rotation type and the split type were designed based on the constant arc length forming method using the design software, UBECO Profil. Finite element analysis was performed to evaluate the suitability of designed flower patterns in terms of the longitudinal strain and the bow defect. The analytical results show that the split type represents more uniform longitudinal strain distributions and a good dimensional accuracy than other types of flower patterns.

• Journal of Institute of Control, Robotics and Systems
• /
• 제15권9호
• /
• pp.877-880
• /
• 2009

A curing process in post-printing section of R2R process is required for an electrical property of the printed pattern when devices such as RFID, Solar cell are printed. PEN as well as heat-stabilized PET which is used as a plastic substrate would be deformed at high temperature due to change of its elastic modulus. And crack in the printed pattern, which is on the plastic substrate is occurred due to the deformation of the substrate. The occurrence of crack causes electrical resistance to increase and the quality of the device to deteriorate. In case of RFID antenna, the range of reading distance is shortened as the electrical resistance of the antenna is increased. Therefore, the deformation of the plastic substrate, which causes the occurrence of crack, should be minimized by setting up low operating tension in R2R process. In low tension, slippage between a moving substrate and a roller would be generated when the operating speed is increased. And scratch would be occurred when slippage is generated due to an air entrainment, which is related to the thickness of the air film. The thickness of the air film is increased when operating speed is increased as shown by simulation based on mathematical model. The occurrence of scratch in conductive pattern printed by roll to roll process is a critical damage because it causes degradation or failure of electrical property of it.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• 제21권3호
• /
• pp.502-510
• /
• 1997

A disturbance rejection controller using eccentricity filtering and LQ control techniques is proposed to alleviate the effecto of major roll eccentricity in multivariable cold-rolling processes. Fundamental problems in multivariable cold-rolling processes such as process time delay inherent in exit thickness measurement and non-stationary characteristics of roll eccentricity signals can be overcome by the proposed control method. The filtered instantaneous estimate of roll eccentricity may be exploited to improve instantaneous estimate of the exit thickness variation based on roll force and roll gap measurements, and a feedforward compensator is augmented as a reference for a gaugemeter thickness estimator. LQ feedback controller is combined with eccentricity filter for the attenuation of the exit thickness variation due to the entry thickness variation. The simulation results show that the roll eccentricity disturbance is significantly eliminated and other disturbances also are attenuated.

• Transactions of Materials Processing
• /
• 제6권2호
• /
• pp.136-144
• /
• 1997

(Ag-10%Ni)/Cu clad metals for electric contact switch were fabricated by cold-roll bonding process. 2 or 3 passes of cold-rolling was carried out for each process to investigate the effect of the rolling passes on the bonding property. The effect of the annealing temperature of copper before the cold-roll bonding on the bond strength was also studied. The specimen bonded with copper annealed below 30$0^{\circ}C$ before roll bonding showed good bond strength. This is because high stored energy in copper promoted the short range diffusion and the grain refinement of copper by the static recrystallization increased the degree of the interfacial coherency. The maximum peel strength of clad metals bonded with Cu annealed below 30$0^{\circ}C$ was 120N.

• Journal of the Korean Society for Precision Engineering
• /
• 제32권7호
• /
• pp.627-631
• /
• 2015

Conventional etching technology is in the face of problems such as dishing, erosion resulting from non-uniform removal of film. Advanced printed circuit board (PCB) requires accurate wire formation with the aid of planarization by chemical mechanical polishing (CMP). Linear roll CMP is a line contact continuous process which removes the film by pressurization and rotation while slurry is supplied to polishing pad attached to the roll. This paper focuses on the design of floating nozzle on the linear roll CMP equipment which makes the slurry supply uniformly on the roll pad. Experimental results show that removal rate using the floating nozzle increases 3 times higher than that without it and non-uniformity is less than 15%.

• Transactions of Materials Processing
• /
• 제28권4호
• /
• pp.190-196
• /
• 2019

The capability of accurately predicting the roll force profile across a strip in the bite zone in cold rolling process is vital for the calculation of strip profile. This paper presents a derivation of a precision mathematical model for predicting variations in the roll force across a strip in cold rolling. While the derivation is based on an approximate 3-D theory of rolling, this mathematical model also considers plastic deformation in the pre-deformation region which is located close to the roll entrance before the strip enters the bite zone. Finally, the mathematical model is expressed as a boundary value problem, and it predicts the roll force profile and tension profile in addition to lateral plastic strain profile.