• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.856-859
• /
• 1996

In this paper, a coarse alignment algorithm for strapdown inertial navigation system is proposed and evaluated analytically. The algorithm computes roll and pitch angles of the vehicle using accelerometer outputs, and then determines yaw angle with gyro outputs. It is referred, as two-step coarse alignment in this work. With the geometric relation between sensor outputs and roll, pitch and yaw angles, the algorithm error is analytically derived and compared with the previous coarse alignment algorithm introduced by Britting. The results show that the proposed two-step coarse alignment algorithm has better performance for pitch angle computation.

• Aerospace Engineering and Technology
• /
• v.11 no.2
• /
• pp.39-48
• /
• 2012

In case a measurement output of gyro sensor is an accumulated angle counts, it is usually provided as a binary bit counter which is allowed to roll-over at its maximum or minimum value. And it is a well known fact that the roll-over behavior restricts the measurement range of the processed sensor output below the actual measurable range of sensor hardware itself. In this study, a conventional sensor data processing method for a gyro with an accumulated angle output is introduced. And also, an improved method which can extend the processed output range over the conventional one is proposed. It is also derived that the increased range depends on the variation speed of a input signal. Finally, the derived equations and the performance of the proposed algorithm are verified using a computer simulation.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.10a
• /
• pp.91-94
• /
• 2005

With increasing demands for large-scale micro-optical components in the field of digital display, the establishment of large-scale fabrication technology fur polymeric patterns has become a priority. The starting point of any polymer replication process is the mold, and the mold often has flat surface. However, It is very hard to replicate large-scale micro patterns using the flat mold, because the cost of large-scale flat mold was very high, and some uniformity and releasing problems were often occurred in large scale flat molding process. In this study, a UV roll imprinting system to overcome the financial and fabrication issues of large-scale pattern replication process was designed and constructed. As a practical example of the system, a lenticular lens with radius of curvature of $223{\mu}m$ and pitch of $280{\mu}m$, which was used to provide wide viewing angle in projection TV, was designed and fabricated. The roll stamper was fabricated using direct machining process of aluminum roll base. Finally, the shape accuracy and uniformity of roll imprinted lenticular lens sheet were measured and analyzed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.3
• /
• pp.113-121
• /
• 2011

Rollover accident is one of the serious traffic accident and rollover accident takes high portion of all accident. The most common type of rollover is a tripped rollover which occupy 95% of all type of single-vehicle rollover. Tripped rollover occurs when a vehicle leaves normal road way and tripped by loose gravel, soil of fixed object such as guard rail, curbs and ditches. And the rest of the type of rollover is un-tripped rollover. An un-tripped rollovers that occurs during high-speed collision avoidance maneuvers. In this paper, presents the explanation of the un-tripped rollover test method and procedure, additionally this paper deals with various occurrence in the un-tripped test such as occurring excessive tire camber in the un-tripped test, tire side-wall contact with road surface and roll oscillation. And this paper analyzes the analysis of the roll rate amplitude in specific frequency through the FFT (Fast Fourier Transform) and the roll angle at the steering reverse timing which is the Fishhook test roll rate feedback time. Finally, this paper analyzes the relations between the estimated steady state roll gain and rollover stability.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.45 no.1
• /
• pp.50-56
• /
• 2008

In this paper, a digital inclinometer to measure the angle and acceleration signals of subject laid on Roll was designed. The designed system consists of a tilt sensor, biaxial accelerometer, single chip microprocessor and Bluetooth module. The designed digital inclinometer was easy to handle and to wear. To evaluate the performance of the system, we measured simultaneously the angle and acceleration signals from the 3 subjects on the Roll using two instruments which are ZEBRIS and designed system. The measured signals were processed by statistical method and then the correlation coefficient of 0.93 was shown. From the results, the designed digital inclinometer is shown to be useful in assessment of body movement.

• Korean Journal of Materials Research
• /
• v.33 no.11
• /
• pp.439-446
• /
• 2023

Changes in the microstructure and mechanical properties of as-roll-bonded AA6061/AA5052/AA1050 three-layered sheet with increasing annealing temperature were investigated in detail. The commercial AA6061, AA5052 and AA1050 sheets with 2 mm thickness were roll-bonded by multi-pass rolling at ambient temperature. The roll-bonded Al sheets were then annealed for 1 h at various temperatures from 200 to 400 ℃. The specimens annealed up to 250 ℃ showed a typical deformation structure where the grains are elongated in the rolling direction in all regions. However, after annealing at 300 ℃, while AA6061 and AA1050 regions still retained the deformation structure, but AA5052 region changed into complete recrystallization. For all the annealed materials, the fraction of high angle grain boundaries was lower than that of low angle grain boundaries. In addition, while the rolling texture of the {110}<112> and {123}<634> components strongly developed in the AA6061 and AA1050 regions, in the AA5052 region the recrystallization texture of the {100}<001> component developed. After annealing at 350 ℃ the recrystallization texture developed in all regions. The as-rolled material exhibited a relatively high tensile strength of 282 MPa and elongation of 18 %. However, the tensile strength decreased and the elongation increased gradually with the increase in annealing temperature. The changes in mechanical properties with increasing annealing temperature were compared with those of other three-layered Al sheets fabricated in previous studies.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1132-1137
• /
• 2007

This paper describes a Unified Chassis Control (UCC) strategy to prevent vehicle rollover by integrating individual modular chassis control systems such as Electronic Stability Control (ESC) and Continuous Damping Control (CDC). The UCC threshold is determined from a rollover index computed by estimated roll angle, roll rate and measured lateral acceleration. A direct yaw moment control method is used to design the ESC based on a 2-D bicycle model. Similarly, the CDC is designed based on a 2-D roll model using a direct roll moment control method. The performance of the proposed UCC scheme is investigated and compared to that of modular chassis controllers through computer simulations using a validated vehicle simulator. It is shown that the proposed the UCC can lead to improvements in vehicle stability and efficient actuation of chassis control systems.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.121.4-121
• /
• 2001

We propose an off-line methodology for detecting a faulty backup roll that generates eccentricity components, under the condition that the feeding velocity, equivalently the angular velocity of roll, is not constant. From a newly devised speed angle conversion algorithm, we transform all process data into those of a virtual process under a constant feeding speed. This indirectly way, we can apply a spectral analysis to the original process. In addition, we develop an online detection method of roll eccentricity based on newly designed PLG sensor. This PLG sensor is robust because of applying magnetic proximity sensnors and non-contact measurement method.

• Transactions of Materials Processing
• /
• v.8 no.6
• /
• pp.583-590
• /
• 1999

New forward slip model has been developed for the precise prediction of rolling speed in the hot strip finishing mill. Besides those influential factors such as neutral point, work roll diameter, friction coefficient, bite angle and the thickness at each side of entry and delivery of the rolls, roll torque was specifically taken into account in this study. To consider the effect of width change on forward slip, calibration factors obtained from rolling torque has been added to new prediction model and refining method has also been developed to reduce the speed unbalance between adjacent stands. The application of the new model showed a good agreement in rolling speeds between the predictions and the actual measurements, and the standard deviation of prediction error has also been significantly reduced.

• Journal of Navigation and Port Research
• /
• v.31 no.7
• /
• pp.597-603
• /
• 2007

A predictive controller can solve a control problem related to a disturbance-dominant system such as roll stabilization of a ship in waves. In this paper, a predictive controller is developed for a fin stabilizer. Future wave-induced moment is modeled simply using two typical regular wave components for which six parameters are identified by the recursive Fourier transform and the least squares method using the past time series of the roll motion. After predicting the future wave-induced moment, optimal control theory is applied to discover the most effective command fin angle that will stabilize the roll motion. In the results, wave prediction performance is investigated, and the effectiveness of the predictive controller is compared to a conventional PD controller.