DOI QR코드

DOI QR Code

Microstructure and Mechanical Properties of AA6061/AA5052/AA1050 Alloy Fabricated by Cold Roll-Bonding and Subsequently Annealed

  • Seong-Hee Lee (Department of Advanced Materials Science and Engineering, Mokpo National University) ;
  • Sang-Hyeon Jo (Department of Advanced Materials Science and Engineering, Mokpo National University) ;
  • Jae-Yeol Jeon (Automotive Materials & Components R&D Group, Korea Institute of Industrial Technology)
  • Received : 2023.09.27
  • Accepted : 2023.10.24
  • Published : 2023.11.27

Abstract

Changes in the microstructure and mechanical properties of as-roll-bonded AA6061/AA5052/AA1050 three-layered sheet with increasing annealing temperature were investigated in detail. The commercial AA6061, AA5052 and AA1050 sheets with 2 mm thickness were roll-bonded by multi-pass rolling at ambient temperature. The roll-bonded Al sheets were then annealed for 1 h at various temperatures from 200 to 400 ℃. The specimens annealed up to 250 ℃ showed a typical deformation structure where the grains are elongated in the rolling direction in all regions. However, after annealing at 300 ℃, while AA6061 and AA1050 regions still retained the deformation structure, but AA5052 region changed into complete recrystallization. For all the annealed materials, the fraction of high angle grain boundaries was lower than that of low angle grain boundaries. In addition, while the rolling texture of the {110}<112> and {123}<634> components strongly developed in the AA6061 and AA1050 regions, in the AA5052 region the recrystallization texture of the {100}<001> component developed. After annealing at 350 ℃ the recrystallization texture developed in all regions. The as-rolled material exhibited a relatively high tensile strength of 282 MPa and elongation of 18 %. However, the tensile strength decreased and the elongation increased gradually with the increase in annealing temperature. The changes in mechanical properties with increasing annealing temperature were compared with those of other three-layered Al sheets fabricated in previous studies.

Keywords

Acknowledgement

This results were supported by "Regional Innovation Strategy (RIS)" through the National Research Foundation of Korea (NRF) funded by the Ministry of Education (MOE) (2021RIS-002).

References

  1. S. Guo, Y. Xu, Y. Han, J. Liu, G. Xue and H. Nagaumi, Trans. Nonferrous Met. Soc. China, 24, 2393 (2014). https://doi.org/10.1016/S1003-6326(14)63362-8
  2. L. Ding, Y. Weng, S. Wu, R. E. Sansers, Z. Jia and Q. Liu, Mater. Sci. Eng., A, 651, 991 (2016).
  3. X. Fan, Z. He, W. Zhou and S. Yuan, J. Mater. Process. Technol., 228, 179 (2016).
  4. J. H. Yang and S. H. Lee, Korean J. Mater. Res., 26, 628 (2016).
  5. W. Chae, B. K. Kim, J. Lee and J. H. Han, Korean J. Met. Mater., 58, 703 (2020).
  6. Y. M. Kim, S. W. Choi, Y. C. Kim and C. S. Kang, Korean J. Met. Mater., 59, 582 (2021).
  7. Y. W. Kim, Y. H. Jo, Y. S. Lee, H. W. Kim and J. I. Lee, Korean J. Met. Mater., 60, 83 (2022).
  8. J. Sun, W. Du, J. Fu, K. Liu, S. Li, Z. Wang and H. Liang, J. Magnesium Alloys, 10, 2649 (2023).
  9. H. Delavar, A. J. Mostahsanb and H. Ibrahimc, J. Magnesium Alloys, 11, 1125 (2023).
  10. D. G. Altenpohl, Aluminum: Technology, Applications and Environment, 6th ed., p.319-394, The Aluminum Association (Arlinton, USA, 1998) and The Minerals, Metals & Materials Society (Pittsburgh, USA, 1998).
  11. H. Yan and J. G. Lenard, Mater. Sci. Eng., A, 385, 419 (2004).
  12. M. J. Ahn, H. S. You and S. H. Lee, Korean J. Mater. Res., 26, 388 (2016).
  13. J. Y. Hwang and S. H. Lee, Korean J. Mater. Res., 29, 392 (2019). https://doi.org/10.3740/MRSK.2019.29.6.392
  14. S. H. Lee, Arch. Metall. Mater., 65, 1093 (2020). https://doi.org/10.24425/amm.2020.133223
  15. S. H. Jo and S. H. Lee, Korean J. Mater. Res., 32, 72 (2022).
  16. S. H. Jo, B. B. Park and S. H. Lee, Korean J. Mater. Res., 32, 388 (2022).
  17. S. H. Jo and S. H. Lee, Korean J. Mater. Res., 32, 72 (2023).
  18. S. H. Lee, Korean J. Met. Mater., 61, 652 (2023).
  19. F. J. Humphreys and M. Hatherly, Recrystallization and Related Annealing Phenomena, 2nd ed., p.221, Elsevier Science Ltd., Amsterdam, Netherlands (2004).