• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.19 no.3
• /
• pp.353-358
• /
• 2010

This research introduces a new and improved design for a pneumatic cylinder driven roll feeder wherein each of the principal rotating feeder parts is configured so as to have feeding accuracy and to be low manufacturing cost. The feed pitch accuracy of the proposed roll feeder was evaluated by measuring lengths of cut offs of the strip stock with a shear attached to an air press. The air press was designed, manufactured, and mounted on the same table of the proposed roll feeder such that the strip stock maintained horizontal plane until the strip stock entered into the shear. The proposed roll feeder and the air press were designed to be operated automatically by a PLC employed controller. The feed pitch accuracy of the proposed roll feeder was analyzed by setting the pitch as 10, 12.5, and 15mm. At each predetermined feed pitch, the proposed roll feeder was tested 300 times as one test set and replicated three times. The average lengths of the cut offs of the strip stock ranged from 9.98 to 10.13mm, from 12.42 to 12.57mm, and from 14.96 to 15.06mm at the predetermined 10, 12.5, and 15mm feed pitch, respectively, among the total of 900 samples of each feed pitch. Main cause of variation of the length of the cut off of the strip stock fed by the proposed roll feeder was considered to be fluctuation of the air press during recompressing period of the air compressor to pressurize the air in the air tank. The largest difference between the maximum and the minimum length of the cut off was appeared while the air compressor recompressing the air. The air compressor used for this study restricted the air delivered to the proposed roll feeder while it was still running. Thus, this air delivery restriction problem should be improved by stabilizing the air press while the proposed roll feeder is running.

• Journal of Institute of Control, Robotics and Systems
• /
• v.17 no.7
• /
• pp.647-650
• /
• 2011

This paper presents the development of roll replacement robot system for wire-rod press rolls. The roll replacement robot system consist of a palletized railway truck, a 6-DOF industrial robot manipulator, a roll changing tool and a hydraulic power system. Results of simulation and pilot experiment show the roll changing task can be successfully automated using proposed robot system.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.22 no.5
• /
• pp.871-878
• /
• 2013

Roll-to-roll (R2R) hot embossing systems have been developed and are widely used in various industrial domains. These systems press and heat flexible films between a press roll and a back-up roll, as said films pass through the two rolls. In previous studies, a heating roll was used for heating. However, in this study, a hybrid roll for R2R hot embossing is conceptualized and developed. This R2R system can be used for generating fine patterns on large and continuous films. The hybrid roll of our system can cool and heat the films simultaneously, thus affording greater flexibility in process design. Thermal and structural analyses were performed for developing the hybrid roll. In addition, a hybrid roll was designed based on analytical results. Experiments were conducted for measuring the performance of the developed hybrid roll.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.26 no.3
• /
• pp.306-312
• /
• 2017

Press rolls are constantly exposed to physical and heat stresses on their surface and are prone to crack, bruise, and spall if the accumulated stress goes beyond the critical point. Such surface phenomenon can cause them to lose their functionality and eventually lead to a halted production line. Eddy current testing can be considered a useful method to investigate the surface of the roll. The method involves the application of a high intensity magnetic field onto the surface of the roll, and thereby finding any early stage of possible defects. When the method was applied for roll inspection, the cross section of the sensor was regulated as per the overall testing speed. A smaller cross sectional area implied a better resolution but a longer testing time. In this paper, a convenient method to increase both overall system resolution and inspection speed of eddy current roll inspection is suggested by using a devised array sensor structure.

• Ocean Systems Engineering
• /
• v.5 no.2
• /
• pp.55-76
• /
• 2015

Of all the six degrees of freedom, the roll motion of a ship is the most poorly understood and displays complicated phenomena. Due to the low potential wave damping at the natural frequency, the effective analysis of ship roll dynamics comes down to the accurate estimation of the viscous roll damping. This paper provides overview of the importance of roll damping and an extensive literature review of the various viscous roll damping prediction methods applied by researchers over the years. The paper also discusses in detail the current state of the art estimation of viscous roll damping for ship shaped structures. A computer code is developed based on this method and its results are compared with experimental data to demonstrate the accuracy of the method. While some of the key references describing this method are not available in English, some others have been found to contain typographic errors. The objective of this paper is to provide a comprehensive summary of the state of the art method in one place for future reference.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.30 no.1
• /
• pp.95-103
• /
• 1998

Many new technologies and developments designed to increase paper machine speeds and improve paper printability have emerged in recent years. These improvements have changed the structure of paper and given winder manufacturers new challenges, especially as the requirements of printing presses have also changed. Ever-increasing roll widths and diameters are needed. Along with faster press speeds and shorter acceleration times, the unwinding of roils in the press room has become a true test of paper strength and roll structure, In the following we will review the special winding features of coated papers and discuss a selection of the winder type to meet a mill's specific needs.

• Ocean Systems Engineering
• /
• v.2 no.4
• /
• pp.239-255
• /
• 2012

Analysis of ship parametric roll has generally been restricted to simple analytical models and sophisticated time domain simulations. Simple analytical models do not capture all the critical dynamics while time-domain simulations are often time consuming to implement. The model presented in this paper captures the essential dynamics of the system without over simplification. This work incorporates various important aspects of the system and assesses the significance of including or ignoring these aspects. Special consideration is given to the fact that a hull form asymmetric about the design waterline would not lead to a perfectly harmonic variation in metacentric height. Many of the previous works on parametric roll make the assumption of linearized and harmonic behaviour of the time-varying restoring arm or metacentric height. This assumption enables modelling the roll motion as a Mathieu equation. This paper provides a critical assessment of this assumption and suggests modelling the roll motion as a Hills equation. Also the effects of non-linear damping are included to evaluate its effect on the bounded parametric roll amplitude in a simplified manner.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.44 no.4
• /
• pp.85-90
• /
• 2012

Wet pressing process has great influence not only on the paper properties but also on the efficiency of total manufacturing process including energy efficiency. The slow drainage propensity of old corrugated container(OCC) might require more complicated control of wet pressing process. In this study, the change in press efficiency and in structure of wet sheet by the various condition of laboratory roll press simulator were evaluated to provide background information about wet pressing of OCC. The higher pressure and the slower machine speed resulted in higher efficiency of wet pressing but the change trends of dryness depending on the wet press pressure and machine speed were shown differently according to OCC treatment. The effects of water contents of felt on the wet press efficiency and sheet structure were also investigated. The higher contents of water in felt resulted in less removal of water generally and the crushed structure of wet sheet were appeared especially at higher pressure.

• Ocean Systems Engineering
• /
• v.7 no.1
• /
• pp.53-74
• /
• 2017

Ship shaped FPSO (Floating Production, Storage and Offloading) units are the most commonly used floating production units to extract hydrocarbons from reservoirs under the seabed. These structures are usually much larger than general cargo ships and have their natural frequency outside the wave frequency range. This results in the response to first order wave forces acting on the hull to be negligible. However, second order difference frequency forces start to significantly impact the motions of the structure. When the difference frequency between wave components matches the roll natural frequency, the structure experiences a significant roll motion which is also termed as second order roll. This paper describes the theory and numerical implementation behind the calculation of second order forces and motions of any general floating structure subjected to waves. The numerical implementation is validated in zero speed case against the commercial code OrcaFlex. The paper also describes in detail the popular approximations used to simplify the computation of second order forces and provides a discussion on the limitations of each approximation.

• Journal of Hydrogen and New Energy
• /
• v.22 no.5
• /
• pp.585-591
• /
• 2011

This study has focused on the development of high performance membrane-electrode assemblies (MEAs) fabricated by decal method for proton exchange membrane fuel cell (PEMFC). To study the effect of ionomer contents on performance, we fabricated MEAs with several electrodes which were prepared by varying the quantity of ionomer from 20 wt.% to 45 wt.% in catalyst layer. The MEA performance was obtained through single cell test. The MEA prepared from electrode with 25wt.% of ionomer showed the best performance. We evaluated the surface area and pore volume of electrode with BET. We found that the surface area and pore volume in electrode decreased rapidly at the electrode with 40wt.% of ionomer in catalyst layer. MEA was fabricated by roll laminator machine and the roll laminating conditions for the preparation of MEA, such as laminating press, temperature and speed, were optimized. The MEA performance is not affected by laminating temperature and speed, but roll laminating press have a great effect on MEA performance.