• Journal of Power System Engineering
• /
• v.19 no.4
• /
• pp.36-42
• /
• 2015

TMixed convective flow in a bottom heated and top cooled rectangular channel can be significantly affected by the channel aspect ratio, Prandtl number, Reynolds number, Rayleigh number and angle of inclination. In such a mixed convection, the flow pattern plays an important role in various technological processes. In this study, a numerical investigation is carried out to explore mixed convection in a three-dimensional rectangular channel with bottom heated and top cooled uniformly. The three-dimensional governing equations are discretized using the finite volume method. In the range of low Reynolds number($0{\leq}Re{\leq}9.6{\times}10^{-2}$), the effects of the aspect ratio($2{\leq}AR{\leq}12$) and Gr/Re are presented and discussed. The longitudinal roll number in the channel is increased with increasing aspect ratio, and the roll number induced, regardless of the aspect ratio number, is even in the range of aspect ratios between 2 and 12, New vortex flow structure containing inclined longitudinal rolls is found, which is affected by aspect ratio and Reynolds number. The ratio Gr/Re is used to check the relative magnitudes of forced and natural convection in the mixed convective flow of high viscous fluid.

• Journal of Digital Contents Society
• /
• v.5 no.4
• /
• pp.306-310
• /
• 2004

In this paper, we proposed a capacity enhancement method using TCM-128QAM modulation and bandwidth extension of 25MHz in HDR-WPAN (high data rate wireless personal area network) system. In case using TCM-128 QAM modulation scheme, we can obtain maximum 66Mbps transmission rate in bandwidth of 15MHz. If extend bandwidth by 25MHz and roll-off coefficient ${\alpha}=0.35$, we can obtain maximum 110Mbps transmission rate. These results are confirmed through PSD(power spectrum density) analysis and BER (bit error rate) performance.

• Journal of Power System Engineering
• /
• v.10 no.1
• /
• pp.96-101
• /
• 2006

In ship operation the consequence of roll and pitchingmotion can seriously degrade the performance of mechanical and personnel effectiveness. So many studies for the roll stabilization and trimming control system design have been performed and good results have been achieved where the stabilizing fins, tanks, rudders and flaps are used. However the ultimate objective of such approach should be focused on improving the boarding sensitivity. But there may exist many unsolved problems, for examples, ship control performance degradation and increasing of system complexity. So, the achieved control performance could not give us enough comfortable boarding sensitivity where the residual rolling and pitching motion are main drawbacks. To get rid of these disadvantages, the main hull control systems design approach has been considered using semiactive absorber. In this system, dampers, spring, dynamic dampers and control system with sensors are incorporated. In our system considered in this study, just two motors and control system with sensors are used for the bed. And the control system can be installed on each bed. So, we can control every bed on the specified control objective respectively. Above all, the good advantages of this system are the facts followed from simple idea and usefulness. Of course the structural modifications are needed. Considering disturbances, we design control system and verify the usefulness of developed system from the experimental study.

• Journal of the Korean Society of Industry Convergence
• /
• v.25 no.6_2
• /
• pp.1029-1036
• /
• 2022

The traditional outdoor advertising market has been stagnant recently, but the digital advertising market has been steadily increasing, and the digital signage market has been expanding despite the recent corona pandemic. However, in terms of hardware, new displays are required due to excessive power consumption, lack of visibility in sunlight, and continuous operating expenses. Since the e-paper display does not require a light emitting device therein, it is advantageous to solve above problems. In addition, it has the advantage of consuming power only when converting an image due to bistability, so it is suitable as hardware that implements images rather than moving pictures. Currently, one of the most successful examples of commercializing e-paper displays is ESL devices. According to a recent market study, the market for large-sized panels larger than 10 inches has grown at an annual rate of 21.6%, and the market is expected to exceed 30% by 2026. It is judged that it will be relatively easy to apply the roll-to-roll technology, which is currently developing the technology applied to OLED, to the e-paper display. Therefore, mass production technology and market expansion for ESL panel enlargement are expected, and a new market is also expected to be formed at the same time. New markets will be traffic signs, public displays, billboards, façades, kiosks, digital signage, and so on.

• Proceedings of the KIPE Conference
• /
• 2016.07a
• /
• pp.475-476
• /
• 2016

According to government supporting a renewable generation, a number of industrial MW photovoltaic systems have already been installed and rapidly increased. Even though the supporting is increased, analysis on power valuation and roll of a photovoltaic system are insufficient. In this paper, comparative analysis on characteristic of photovoltaic power system are illustrated as basic of power valuation by collecting power and irradiation data from MW photovoltaic system on wide area.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.4
• /
• pp.190-196
• /
• 2001

The naval vessel must moves rolling, pitching, yawing by wave when it runs in ocean. Some narrow beam antenna needed position compensation by stabilizer or gimbal for best performance. This paper presents the precision position control for heavy weight(130kg) in roll and pitch direction. Generally it's called for gimbal. This gimbal uses P-I controller, and it's driven by linear actuator and servo motor. This gimbal gets ship's gyro signal and synchro, which have the absolute angle value. Some other similar equipments are driven by huge hydraulic power, but this gimbal is driven by small servo motor. This control loop gets the following procedure repeatedly; reading ship gyro and gimbal synchro, calculating compensated error and control output, driving motor and actuator The performance of gimbal system was satisfied.

• Proceedings of the Korean Institute of Interior Design Conference
• /
• 2007.05a
• /
• pp.77-78
• /
• 2007

This project has been designed for people to experience and understand the process, importance and benefit of coal fire plants. As the biggest and first typical Korean fire plant using coal, Boryeong fire plant has had important roll for the Korean industries. Even so, people has had wrong prejudice for the fire plant in terms of environmental protection. To do these kind of rolls, this museum has been designed with theme, "Boryeong fire plant mating symbiotic relationship between nature, human and technologies." The space was zoned with five major themes: i. circulation of energy in nature, ii. electric power and eco-fire plant, iii. future energy, iv roll for future of environment, v. Korea as the leading energy industry. The design has been developed focused on spatial experiences to make 'Design Sequence' with linear circulations haying several important destinations. The interior has been finished with minimal color and materials projected by big sized movie and various LED movie system. Concept of appordance has been used to make interactive experiences between exhibits and visitors.

• Transactions of Materials Processing
• /
• v.25 no.1
• /
• pp.5-11
• /
• 2016

The control of the roll velocities is essential in maintaining stability during ring rolling, but such control is difficult. The determination of the best roll velocities can be helped with the use of FE simulations and processing maps, which give the useful information such as power dissipation and flow instability for hot metal forming processes. In the current study, the workability of 7050 aluminum alloy is evaluated by using processing map. With the developed information, the stability of the ring rolling condition, called the Constant Growth Velocity Condition (CGVC), is evaluated.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.11a
• /
• pp.964-968
• /
• 1996

The demands of size and quality of large steel shaft forgings for ship building, power plant, steel plant, etc. are rapidly increasing, and some of these productions are manufactured from ingot weighing more than 300 tons. For use as rotating components. shafts require toughness, strength and homogeneity, and therefore are produced through a variety of heat treatments. According to the increase of ingot size, micro- and macrosegregation and also mass effect of the product increase. Thus, special care should be paid to the heat treatment of such large shaft forgings. In this paper, the heat treatment of large shaft forgings such as rotor and back-up roll is calculated using the commercial finite element code SYSWELD. Calculated distributions of temperature and phase are compared with experimental data. The continuous cooling transformation diagram, thermal and mechanical properites of each phase are used. The phase proportion, hardness and residual stress during water quenching are discussed.

• Journal of Advanced Marine Engineering and Technology
• /
• v.14 no.2
• /
• pp.35-47
• /
• 1990

The natural frequency of lateral vibration for ship's propulsion shafting tends to become lower as the relative stiffness of supproted system of the propulsion shafting decreases and the weight of shafting increases. Especially, the propulsion shafting of high-power ships such as car ferries, roll-on/roll-off, and container ships are susceptible to lateral vibration for their resonant speeds are happened to be in ordinary operating speed ranges. So far, many papers on the lateral vibration of ship's propulsion shaftings are published but they treated mainly special cases and not explained explicitly the calculation process. In this paper, the calculation processes of undamped and also forced damped lateral vibration by the transfer matrix method are presented and the calculation programs are developed. With the developed computer programs, a ship's propulsion shafting which was introduced on the published paper is analyzed for its lateral vibration and also the lateral vibration of the main drive shaft for a lathe is calculated to show the availiability of developed computer programs.