• 제어로봇시스템학회논문지
• /
• 제17권7호
• /
• pp.647-650
• /
• 2011

This paper presents the development of roll replacement robot system for wire-rod press rolls. The roll replacement robot system consist of a palletized railway truck, a 6-DOF industrial robot manipulator, a roll changing tool and a hydraulic power system. Results of simulation and pilot experiment show the roll changing task can be successfully automated using proposed robot system.

• 제어로봇시스템학회논문지
• /
• 제14권7호
• /
• pp.689-694
• /
• 2008

This paper proposes a roll rate estimation method for spinning vehicles. The carrier phase and frequency variations caused by spinning of vehicles are observed and the roll rate estimator is designed on the observation. The roll rate estimator consists of phase detector and zero crossing counter. The phase detector computes phase variation using in-phase and quadrature value from the correlator. By using zero crossing counter, the roll rate can be estimated since the output of phase detector is changed in proportion to the roll rate. Experiment a results show that estimated roll rate error is smaller than 0.0578Hz.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 제3회 압연심포지엄 논문집 압연기술의 미래개척 (Exploitation of Future Rolling Technologies)
• /
• pp.208-216
• /
• 1999

Nowadays coustomer's needs for high surface quality steel sheet has greatly increased, so it is necessary to pay more attention to the roll grinding, texturing and handling. POSCO can acquire high surface quality roll and high productivity through World-first fully automated Roll Shop system which had been constructed '94.10.1∼'97.8.28 at Kwangyang Works. Roll Shop Automation System consists of Level-I, II, III control system and 23 automated machines. After the completion of the construction, the system started smoothy and keeps its operation with high productivity as expected. The installation of this system gave an epoch-making man power saving. This paper introduce its main facilities and operation.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2002년도 ICCAS
• /
• pp.74.2-74
• /
• 2002

$\textbullet$ Roll Control $\textbullet$ Switched Reluctance Motor $\textbullet$ Field Programmable Gate Array $\textbullet$ Single Pulse Mode Current Control $\textbullet$ OR/Off Angle Control

• 동력기계공학회지
• /
• 제13권1호
• /
• pp.26-32
• /
• 2009

This study is about roll characteristics evaluation to show the advantage of using MR(magneto-rheological) dampers for steering of a SUV(sports utility vehicle). Roll characteristics is very important to observe the roll-propensity of the SUV. ADAMS/Car program was used to simulate the basic steering motion, using 63 D.O.F. vehicle model. Sky-Hook and Ground-Hook control algorithms were used as a semi-active suspension system controller. The roll characteristics from the steering motion were compared between the simulation results from the semi-active suspension system and the passive suspension system.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.654-657
• /
• 2000

In the winding system, the constant tension control is too important. In this study, we've used a variable PID system as a function of a radius of winding roll. As a result, it was possible to measure a winding roll radius in the real time by making a mathematical model for measuring a winding roll radius. Finally, we've compared PID parameters as a function of winding roll radius after getting PID parameters in terms of the Ziegler & Nichols(ZN) method.

• International Journal of Automotive Technology
• /
• 제3권3호
• /
• pp.123-128
• /
• 2002

This paper presents the design of an active roll control system for a ground vehicle and an experimental study using an devised electric-actuating roll control system. Based on a three degree of freedom linear vehicle model, the controller is designed using lateral acceleration and rollrate feedback. In order to investigate the feasibility of an active control system, experimental work is carried out using a hardware-in-the-loop (Hil) setup which has been constructed by the devised electric-actuating system and the full vehicle model including tire characteristics. The performance is evaluated by an experiment using the Hil setup with limited bandwidth. Finally, in order to enhance the control performance in the transient region, a hybrid control strategy is proposed and evaluated.

• 한국정밀공학회지
• /
• 제31권11호
• /
• pp.987-992
• /
• 2014

Register control of roll-to-roll printing system for printed electronics requires accurate measurement of register errors. The register marks used for the recognition of patterns position between layers have inherently defects due to low printability of register marks themselves, which brings out inaccurate register accuracy and consequently low performance of printed electronics devices. In this study, the compensation methods for the unrecognized or missing register data are proposed to improve the recognition and consequently the control performance of register accuracy in roll-to-roll printing equipment. The compensation methods using the prior data and the linear interpolation are proposed and compared with the case without compensation for the simulation as well as experiment. Only the linear interpolation method could successfully compensate the missing data and consequently improve the register control performance. We should apply the compensation process of the register errors to improve the register control accuracy in the roll-to-roll printing equipment.

• 한국군사과학기술학회지
• /
• 제24권1호
• /
• pp.123-132
• /
• 2021

In order for the underwater vehicle to perform various tasks, it is important to control the depth, course, and roll of the underwater vehicle. To design such a controller, it is necessary to construct a dynamic model of the underwater vehicle and select the appropriate hydrodynamic coefficients. For the controller design, since the dynamic model is linearized assuming a limited operating range, the control performance in the steady state is well satisfied, but the control performance in the transient state may be unstable. In this paper, in order to overcome the problems of the existing controller design, we propose a A2C(Advantage Actor-Critic) based roll controller for underwater vehicle with stable learning performance in a continuous space among reinforcement learning methods that can be learned through rewards for actions. The performance of the proposed A2C based roll controller is verified through simulation and compared with PID and Dueling DDQN based roll controllers.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 제3회 압연심포지엄 논문집 압연기술의 미래개척 (Exploitation of Future Rolling Technologies)
• /
• pp.27-36
• /
• 1999

To have high flatness quality of hot rolled strip in the hot strip finishing mill train, a new inter-stand tension profile measuring device of segmented looper roll type(coined as Flatness Sensing Inter-stand Looper, FlatSIL) and a new flatness control system have been developed in this study. The device measures the strip tension profile across the strip width and informs the strip wave pattern to new flatness control system where work roll bending mode to relieve the strip wave is determined. The existing automatic shape control system which uses laser type shape-meter installed at the outlet of the last finishing mill stand strip tension between down coiler and last finishig mill since the latent wave concealed by the strip tension between down coiler and last finishing mill stand cannot be measured by the laser distance-meter. Thus the existing shape control system is not able to control the flatness through the full strip length. The new flatness control system, however, works for full strip length during strip rolling as far as the tension profile measuring device and work roll bender are on. With the new flatness control system, work roll bender is automatically controller to minimize the latent wave of the running strip and the flatness quality as well as strip travelling stability has been noticeably improved from strip head through body to tail.