• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.1488-1493
• /
• 2003

Recently, higher and bigger building is trend of the construction. Accordingly the building material is getting bigger and construction equipments are developed. But operation is still depends on human resource. Therefore there have several problems that are safety, laborious operation, and shortage of worker. In the various construction sites, the automation in construction is introduced to solve these problems. This paper proposed the automation system in construction that installs curtain wall in a high building. The system is expected effects that are reduction of a construction period, retrenchment of the cost and assurance of safety.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2004.06a
• /
• pp.133-134
• /
• 2004

DUPIC (Direct Use of spent PWR fuel In CANDU) fuel cycle technology is being developed at Korea Atomic Energy Research Institute (KAERI). All the DUPIC fuel fabrication processes are remotely conducted in the completely shielded M6 hot-cell located in the Irradiated Material Examination Facility (IMEF) at KAERI. Undesirable products such as spent nuclear fuel powder debris and contaminated wastes are inevitably created during the DUPIC nuclear fuel fabrication processes.(omitted)

• 제어로봇시스템학회:학술대회논문집
• /
• 2002.10a
• /
• pp.43.6-43
• /
• 2002

$\textbullet$ KAEROT/m1 with an omni-directional planetary wheel mechanism for the narrow corridor. $\textbullet$ KAEROT/m2 can pass over the ditch with specially designed four wheel of a re-configurable crawler. $\textbullet$ Stereo imaging system with master manipulator enhancing the tele-presence. $\textbullet$ Small hybrid dosimeter detecting radiation dose and dose rate simultaneously.

• Proceedings of the IEEK Conference
• /
• 2000.07b
• /
• pp.600-603
• /
• 2000

In this paper, we propose the design method of distributed control system using Controller Area Network (CAN). CAN is an advanced serial communication protocol for distributed real-time control systems. It is a contention-based multi-master network whose timeliness properties come from its collision resolution algorithm which gives a high schedulable utilization and guaranteed bus access latency. With proposed method using CAN, we apply to robot controller. The effectiveness of proposed method is demonstrated by the simulation and experiment.

• Korean Journal of Computational Design and Engineering
• /
• v.12 no.1
• /
• pp.50-57
• /
• 2007

In recent years, many robotics researches have been focused on developing human-friendly robots, that is, humanoid biped robots. The researches of humanoid robots include various areas such as hardware development, control of biped locomotion, artificial intelligence, human interaction, etc. The present work concerns the hardware development of a mid-size humanoid robot, BONOBO, focusing on rapid development of outer body parts with integrated application if CAD/CAM/CAE/RP. Most parts are three-dimensionally designed using 3D CAD, and effectively connected with CAE analyses using both kinematic simulation and structural analysis. In order to reduce lead time and investment cost for parts developments, Rapid Prototyping (RP) and CAM are selectively utilized for manufacturing body parts. These master parts are then replicated using the vacuum casting process, from which we can obtain plastic parts repeatedly. Through this integrated approach, the first prototype of BONOBO can be successfully developed with relatively low time and investment costs.

• Journal of Institute of Control, Robotics and Systems
• /
• v.22 no.8
• /
• pp.590-596
• /
• 2016

Biopsy is a typical needle type intervention procedure performed under radiographic image equipment such as computed tomography (CT) and cone-beam CT. This minimal invasive procedure is a simple and effective way for identifying cancerous condition of a suspicious tissue but radiation exposure for the patients and interventional radiologists is a critical problem. In order to overcome such trouble and improve accuracy in targeting of the needle, there have been various attempts using robot technology. Those devices and systems, however, are not for full procedure automation in biopsy without consideration for tissue sampling task. A robotic end-effector of a master-slave tele-operated needle type intervention robot system has been proposed to perform entire biopsy procedure by the authors. However, motorized sampling adopted in the device has different cutting speed from that of biopsy guns used in the conventional way. This paper presents the design of a novel robotic mechanism and protocol for the automation of biopsy procedure using spring-triggered biopsy gun mechanism. An experimental prototype has been successfully fabricated and shown its feasibility of the automated biopsy sequence.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.9
• /
• pp.3876-3881
• /
• 2012

In typical master/slave teleoperation systems, a human operator generally manipulates the master to control the slave through the visual information like camera image. However, the operator may get into trouble due to the limited visual information depending on the camera positions and the delay on the visual information because of low communication bandwidth. To cope with this inherit problem in the camera-based teleoperation system, this paper presents a teleoperation system using a reconstructed graphic model instead of the camera image. The proposed teleoperation system consists of a robot control module, a master module using a force-reflective joystick, and a graphic user interface (GUI) module. The graphic user interface module provides the operator with a 3D model reconstructed using a small set of sensing data received from the remote site. The proposed teleoperation system is evaluated through a peg-in-hole assembly task.

• The Journal of the Korea Contents Association
• /
• v.18 no.7
• /
• pp.322-329
• /
• 2018

Teleoperation is defined with a master device that gives control command and a slave robot in a remote site. In this field, it is common that a human operator executes and experiences teleoperation with a virtual slave, and preliminary learns dynamic characteristic and network environment from both agents. Generally, a virtual slave has neglected forward dynamics and its kinematic model has been implemented in computer graphics. This makes a operator to experience actual feelings. This paper proposes a dynamic teleoperation model in which a robotic forward model is applied. Also, a novel compensation method is proposed to reduce the numerical error problems in forward dynamics caused by low control sampling rate. Finally, its results will be compared to the teleoperation in an actual environment.

• Korean Journal of Computational Design and Engineering
• /
• v.13 no.6
• /
• pp.429-439
• /
• 2008

With a remote operated manipulator system, the situation at a remote site can be rendered through remote visualized image to the operator. Then the operator can quickly realize situations and control the slave manipulator by operating a master input device based on the information of the virtual image. In this study, the remote operator visual support system (ROVSS) was developed for viewing support of a remote operator to perform the remote task effectively. A visual support model based on virtual environment was also inserted and used to fulfill the need of this study. The framework for the system was created by Windows API based on PC and the library of 3D graphic simulation tool such as ENVISION. To realize this system, an operation test environment for a limited operating site was constructed by using experimental robot operation. A 3D virtual environment was designed to provide accurate information about the rotation of robot manipulator, the location and distance of operation tool through the real time synchronization. In order to show the efficiency of the visual support, we conducted the experiments by four methods such as the direct view, the camera view, the virtual view and camera view plus virtual view. The experimental results show that the method of camera view plus virtual view has about 30% more efficiency than the method of camera view.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.51 no.2
• /
• pp.55-60
• /
• 2002

This paper presents a controller for the multiple DC motors using the CAN(Controller Area Network). The controller has a benefit of reducing the cable connections and making the controller boards compact through the network including expansibility. CAN, among the field buses, is a serial communication methodology which has the physical layer and the data link layer in the ISO's OSI (Open System Interconnect) 7 layered reference model. It provides the user with many powerful features including multi-master functionality and the ability to broadcast / multicast telegrams. When we use a microprocessor chip embedding the CAN function, the system becomes more economical and reliable to react shortly in the data transmission. The controller, we proposed, is composed of two main controllers and a sub controller, which have built with a one-chip microprocessor having CAN function. The sub controller is plugged into the Pentium PC to perform a CAN communication, and connected to the main controllers via the CAN. Main controllers are responsible for controlling two motors respectively. Totally four motors, actuators for the biped robot in our laboratory, are controlled in the experiment. We show that the four motors are controlled properly to actuate the biped robot through the network in real time.