• 제목/요약/키워드: Roads

검색결과 2,323건 처리시간 0.031초

실시간 강수량을 고려한 도로 침수위험지수 개발 방법에 대한 연구 (A Study on the Development of the Flood Risk Index for Roads Considering Real-time Rainfall)

  • 김은미;황현숙;김창수
    • 한국멀티미디어학회논문지
    • /
    • 제16권5호
    • /
    • pp.610-618
    • /
    • 2013
  • 과거와는 다른 형태의 기상 현상으로 인해 농경지 중심의 침수 피해가 도시 지역의 내수 침수 피해 중심으로 홍수 피해 지역이 변화하고 있다. 이로 인해 인명 및 재산 피해뿐만 아니라 사회기반시설에 대한 피해도 급격히 증가하고 있다. 또한 도로 침수로 인해 운전자의 고립 및 교통 체증의 심화로 인해 경제적으로 큰 피해를 주고 있는 실정이다. 이에 본 연구에서는 과거 기상 정보 및 침수 피해 이력을 활용하여 시 군 구의 행정 구역 형태로 제공되던 침수위험지수를 도로 중심의 집약적인 형태로 제공하는 방법을 시도하고자 한다. 또한 기상청에서 제공되는 실시간 성격의 강수량을 활용하여 강우 당시의 도로별 침수 위험 정도를 정량적으로 제공하여 사용자로 하여금 침수된 도로에 의한 고립을 사전에 방지하고자 한다.

청양-홍성간 도로에서의 강우 시 비점오염 유출특성 및 오염부하량 분석 (Runoff Characteristics and Non-point Source Pollution Loads from Cheongyang-Hongseong Road)

  • 이춘원;강선홍;안태웅;양주경
    • 상하수도학회지
    • /
    • 제25권2호
    • /
    • pp.265-274
    • /
    • 2011
  • Nowadays, the importance of non-point source pollution treatment is being emphasized. Especially, the easy runoff characteristic of highly concentrated pollutants in the roads makes the circumstance more complicated due to impermeability of roads. When the pollutants flow into steam it could make water quality in stream worse and it also causes a bad influence in the aquatic ecosystem because the effluents of rainfall-runoff may contain indecomposable materials like oil and heavy metals. Therefore, we tried to figure out the property of non-point source pollution when it is raining and carried out an assessment for the property of runoff for non-point source pollution and EMC (Event Mean Concentrations) of the essential pollutants during this study. As the result of the study, the EMC was BOD 5.2~21.7 mg/L, COD 7.5~35.4 mg/L, TSS 71.5~466.1 mg/L, T-N 0.682~1.789 mg/L and T-P 0.174~0.378 mg/L, respectively. The decreasing rate of non-point pollutant in Chungyang-Hongsung road indicates the maximum decrease of 80% until 5 mm of rainfall based on SS concentration; by the rainy time within 20~30 minutes, the decreasing rate of SS concentration was shown as 88.0~97.6%. Therefore it was concluded that it seems to be possibly control non-point pollutants if we install equipments to treat non-point pollutants with holding capacity of 30 min. It is supposed that the result of this study could be used for non-point pollutants treatment of roads in Chungyang-Hongsung area. We also want to systematically study and consistently prepare the efficient management of runoff from non-point source pollution and pollutant loading because the characteristics of non-point source pollution runoff changes depending on different characteristics and situations of roads and rainfall.

지리산 국립공원 내 도로에 의한 산림조각화 (Forest Fragmentation Due to Roads in Chirisan National Park)

  • 백경진;박경;강혜순
    • 한국환경복원기술학회지
    • /
    • 제8권1호
    • /
    • pp.63-72
    • /
    • 2005
  • Chirisan National Park, the first and largest one out of 20 national parks in Korea, is divided into five zones. They are composed of nature preservation zone, natural environment zone, natural residential zone, concentrated residential zone, and collective facility zone. However, the park is not a continuous habitat: roads, trails, local residences, and various facilities created the habitat mosaics severely fragmented. We investigated the fragmentation pattern of the park due to roads and mountain trails using GIS. Based on perimeter length, area, and the ratio of perimeter to area of each patch, we obtained landscape analysis indices which reflect the regularity of the patch shape. The 1 m-wide hiking trails divided the park into 491 fragments. The legal trails with 1.5 m - 3 m width which have been heavily used by hikers generate 58 fragments. Even the nature preservation zone, corresponding to a core zone comprising 31.8% of the park area, was divided into 37 fragments because of the roads and mountain trails. With the different widths of buffer applied, the core sizes of the fragments were reduced. When the 60 m buffer was applied, the patch interior areas ranged from 0.0001 to 47.77 $km^2$ with a mean of 7.08 $km^2$. The landscape shape indices were far greater than 1 for most of the cases with a maximum value of 25. These results clearly indicate that Chirisan National Park is not a continuous habitat, but mosaics of small, irregularly shaped habitat fragments. It is necessary to take the size and shape of the fragmented habitats into consideration when nature conservation is planned, especially for large wildlife such as brown bears.

일반국도의 도로 유형별 설계시간계수 산정 및 경제성 평가 (Estimation of K-factor according to Road Type and Economic Evaluation on National Highway)

  • 김태운;오주삼
    • 한국콘텐츠학회논문지
    • /
    • 제15권11호
    • /
    • pp.582-590
    • /
    • 2015
  • 도로 유형 분류 및 설계시간계수는 도로의 차로수 설계 시 중요한 역할을 하고 있다. 본 연구에서는 도로의 유형분류 및 설계시간계수를 추정하였으며, 설계시간계수의 타당성 입증을 위해 경제성 평가를 시행하였다. 도로 유형의 분석 결과 관광부 도로는 일교통량 편차가 크고 주말 계수, 휴가철 계수가 높았다. 지방부 도로는 평일 교통 패턴과 주말 교통 패턴이 유사하고, 도시부 도로는 AADT가 높고 일교통량 편차가 작은 것으로 나타났다. 변곡점 탐색을 통하여 설계시간계수를 산출하였으며, 산출된 설계시간계수를 바탕으로 차로수를 산정하여 도로용량편람의 설계시간계수로 차로수를 산정하였을 경우와 경제성 분석을 통하여 비교하였다. 경제성 분석결과 본 연구의 설계시간계수로 도로 설계 시 4,708억 원 절감할 수 있는 것으로 나타났다. 이는 본 연구 결과의 지방부 4차로 도로에 대한 설계시간계수가 경제적으로 타당하다는 것을 의미한다.

위성영상에서 도로 추출을 위한 히스토그램 기반 경계선 추출자 (Histogram-based road border line extractor for road extraction from satellite imagery)

  • 이동훈;김종화;최흥문
    • 대한전자공학회논문지SP
    • /
    • 제44권5호
    • /
    • pp.28-34
    • /
    • 2007
  • 위성 영상에서 도로를 효과적으로 추출하기 위한 히스토그램 기반 도로 경계선 추출자를 제안하였다. 제안한 추출자를 이용해 도로 경계선 양측의 도로와 비도로 영역 각 화소의 방향성 히스토그램 차를 계산하고, 그 에지 강도 맵을 구하여 도로의 경계선을 추출하였다. 그리고 원영상과 분할된 도로 군집 영상의 에지 강도 맵을 계층적으로 구하여 직선 도로와 곡선 도로를 추출한 다음, 도로의 연결성을 기반으로 하여 전체 도로망을 구성하였다. 제안한 추출자는 칼라 유사도를 계산하는 기존 방법과 달리 히스토그램 차를 기반으로 하기 때문에 잡영에 강건하게 도로를 추출할 수 있으며, 도로 경계선의 위치와 도로 폭도 함께 추출할 수 있을 뿐만 아니라 도로군집을 자동식별하기 때문에 다양한 분광특성의 도로들도 쉽게 추출할 수 있다. 제안한 추출자를 이용하여 1m의 공간 해상도를 갖는 IKONOS 위성 영상에 대해 실험하여 잡영에 강건하게 도로가 추출됨을 확인하였고, 직선 도로 뿐만 아니라 곡선도로 추출도 용이함을 확인하였다.

고속도로 휴게소 연결로 설계 기준 설정에 관한 연구 (A Development of the Design Guidelines for Connecting Roads in Highway Rest Area)

  • 이철수;원제무
    • 한국도로학회논문집
    • /
    • 제15권1호
    • /
    • pp.143-154
    • /
    • 2013
  • PURPOSES: Design of approach roads of rest areas in highway has many drawbacks such as geometric design elements. There has been traffic accidents occured in these approach roads of rest areas. Thus, design criteria is required in order to protect accidents from being occurred. In case of Korea, geometric structure design criteria of entry facilities, such as toll-gate, interchange, junction etc was established. However there are no presence in a detailed standards for geometric structure of the rest area which affiliated road facilities. METHODS: In this study, analytic on accidents was carried out in regards to the entry of geometric structure of resting areas by utilizing a sight survey and an investigation research of traffic accidents. The survey was targeting 135 general service areas. Collisions with physical channelization and safety facilities occurred due to speeding, rapid entry, and etc at the entrance nose section. At the entrance connector roads, accidents caused by speeding, negligence, over-operation of handle of drivers were main reason of accidents. Discriminant analysis were conducted about geometric elements to distinguish influencing factors for traffic accidents. the lengths and access angles of the entrance connector roads were regarded as to have the high relation with traffic accidents. RESULTS: After classifying the design section of resting areas' entry as well as derive design elements on each section, a speed measurement by targeting entry of rest areas and car behavior surveys were performed, then each element's minimum standard was derived through the analyses. According to the speeds at the starting/end point of entrance connector road, the range of the junction setting angle of the entrance connector road is defined as $12^{\circ}{\sim}17^{\circ}$ and the connector length model was suggested. CONCLUSIONS: Suggest improvement plans for existing rest areas that can be applied realistically. This should be corresponded to the standards of entry and exit of developed rest areas.

일반도로와 자전거도로에서의 카고바이크 화물 적재함 진동 특성 비교 (Comparison of Vibration Characteristics of Cargo Bikes on General Roads and Bicycle Roads)

  • 김동율;유명국;이행석;김상민
    • 한국포장학회지
    • /
    • 제29권3호
    • /
    • pp.175-179
    • /
    • 2023
  • This paper analyzes the vibration characteristics within the cargo compartment of a three-wheeled cargo bike when used on both regular roads and dedicated bicycle lanes. When cargo is loaded into the cargo compartment of a cargo bike and driven on the road, the shocks and vibrations transmitted from the ground can potentially affect the transported goods and even lead to product damage. As the vibration characteristics applied to the cargo compartment may vary depending on the condition of the road, vibration sensors were attached to the cargo bike's cargo compartment for data collection during operation on different road types. According to KS T ISO 13355 standards, the cargo bike can withstand vibrations within the range of 10 Hz to 60 Hz when operating on both bicycle lanes and regular roads. However, it is observed that there are peaks exceeding the profile in the frequency range of 3-6 Hz. In the 70-200 Hz range, the profile is exceeded on both regular roads and bicycle lanes, with a tendency for higher exceedance on bicycle lanes. The Grms value within the frequency range of KS T ISO 13355 is 5.926 m/s2 (0.604 Grms). When operating on bicycle lanes with cargo, the Peak envelope optimization PSD value is 6.553 Grms, while on bicycle lanes, it is 7.708 Grms, indicating a difference of at least tenfold.

유비쿼터스 도로재해관리시스템 개발연구 (The Development of Ubiquitous Road Disaster Management System)

  • 성동권;최영택;고제웅;조기성
    • 한국측량학회:학술대회논문집
    • /
    • 한국측량학회 2007년도 춘계학술발표회 논문집
    • /
    • pp.301-306
    • /
    • 2007
  • Because the cost of road management is increasing proportional to road construction, there are needs to build general and systematic road management system. To solving such problems, Ministry of Construction and Transportation started research and development of Highway Management System(HMS), and established a foundation for systematic road management system. But, the implementation of HMS has some limitations because it is just converting roads of physical space to roads of electronic space and managing roads of electronic space. Although HMS offers many conveniences compared to old system which was based hard-copy and paper maps or unit operations, it can not overcome the problem of inefficency of road management due to the separation of operation between outer field and inner office. Therefore, to overcome such inefficency, this study focused on Road Disaster Management System development based on Ubiquotous.

  • PDF

사륜구동 오토바이(ATV)용 차동제한장치(LSD) 개발에 관한 연구 (A Study on the Development of Limited Slip Differential on All Terrain Vehicle)

  • 김준안;전재억
    • 한국기계가공학회지
    • /
    • 제10권1호
    • /
    • pp.8-15
    • /
    • 2011
  • ATV(All Terrain Vehicle) has been developed to be used for agricultural fields on unpaved roads but now it is mostly used to transport a short distance and play leisure sports at mountains. Recently, main concerns on the automobile industry is developing not only a car safe, high fuel efficient and friendly related with environment but also two-wheeled vehicles. In order to maintain high fuel efficiency and safety of two-wheeled vehicle, it is essential that ATV should be set up differential gear. But we worried for ATV which had been set up differential gear not to run on unpaved roads. Therefore, it is necessary to develop LSD(Limited Slip Differential) that maintains existing advantages of ATV and ensures ATV to travel safely on roads. Now LSD equipped cars have a complicated structure, so setting up on ATV is unsuitable. Therefore, in this study, we have developed simple, small and well operating LSD.

A Study on the Road Extraction Using Wavelet Transformation

  • Lee, Byoung-Kil;Kwon, Keum-Sun;Kim, Yong-Il
    • 대한원격탐사학회:학술대회논문집
    • /
    • 대한원격탐사학회 1999년도 Proceedings of International Symposium on Remote Sensing
    • /
    • pp.405-410
    • /
    • 1999
  • Topographic maps can be made and updated with satellite images, but it requires many human interactions that are inefficient and costly. Therefore, the automatizing of the road extraction procedures could increase efficiency in terms of time and cost. Although methods of extracting roads, railroads and rivers from satellite images have been developed in many studies, studies on the road extraction from satellite images of urbanized area are still not relevant, because many artificial components In the city makes the delineation of the roads difficult. So, to extract roads from high resolution satellite images of urbanized area, this study has proposed the combined use of wavelet transform and multi-resolution analysis. In consequence, this study verifies that it is possible to automatize the road extraction from satellite images of urbanized area. And to realize the automatization more completely, various algorithms need to be developed.

  • PDF