• Journal of Welding and Joining
• /
• v.14 no.3
• /
• pp.66-74
• /
• 1996

In this study, friction and wear properties of flame sprayed specimens and hard Cr plating specimens were tested, and their properties were compared each other in dry and lubrication condition. Ni-Cr powder and steel powder were used as the spray powder and sprayed on the steel(S45C) substrate by flame sprayed method. Each wear surface was observed with SEM after friction and wear test. The friction coefficient of the as-forged steel specimens was the highest among surface treatment specimens, and the other specimens appeared in order as follows ; hard Cr-plating specimens, Ni-Cr powder sprayed specimens, steel powder sprayed specimens. Comparing the wear volumes in dry condition, as forged steel specimens appeared the greatest wear volume, and the other specimens appeared wear volume in order as follows ; Ni-Cr powder sprayed specimens, steel powder sprayed specimens, hard Cr plating specimens. In friction and wear test, the hard Cr plating specimens were worn by the abrasive phenomenon, involving the cracks. The wear volume of steel powder sprayed specimens was lower than that of Ni-Cr powder sprayed specimens. Comparing the tensile strength of both sprayed coating layers, the steel powder sprayed coating layer was better than Ni-Cr powder sprayed coating layer.

• Tribology and Lubricants
• /
• v.10 no.1
• /
• pp.14-26
• /
• 1994

The minimum oil film thickness(MOFT) in the connecting-rod bearing of a 1.5 liter, L-4, gasoline engine is measured up to 5500 rpm and calculated to study the dynamically loaded engine bearing. Short bearing approximation and Mobility method are used for theoretical analysis of oil film characteristics. And cylinder pressure, crank-pin surface temperature and bearing temperature are measured as the input data of theoretical analysis. The MOFT are measured by the total capacitance method(TCM). To improve the reliability of the test results, a reasonable determination method of bearing clearance is introduced and used, and the effects of cavitation and aeration on the test results are neglected. The crankshaft is grounded by means of a slip ring. A scissor type linkage system was developed to measure the MOFT and bearing temperature. The effects of engine speed, load and oil viscosity on the measured and calculated minimum oil film thicknesses are investigated at 1500 to 5500 rpm. From the comparison between the measured and calculated MOFT, it is found that a qualitative similarity exists between them, but in all cases, the measured MOFT are smaller than those calculated.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.30 no.2
• /
• pp.71-77
• /
• 1994

A serious of study is carried out to practical use of the three-slot cambered otter board improved by the authors. As the first step, we designed main plates, slots and accessories, such as holding plate, fan-shaped towing plate, normans, center ring, etc. Standing on this design, we made the simple cambered and three-slot cambered model otter board with accessories in a linear scale 6:1. and carried out model test to examine the efficiency of these boards. The obtained results can be summarized as follows: 1. On the simple cambered board with accessories, the values of the maximum shear coefficient($C _{LX}$ ). drag coefficient(($C _{D}$) and hydrodynamic efficiency($C _{L}$/$C _{D}$ ) are 1.39, 0.56, 2.48 at $22^{\circ}$ of the angle of stall respectively. 2. On the three-slot cambered board with accessories, $C _{LX}$/$C _{D}$ and $C _{I}$/$C _{D}$ are 1.67, 0.92, 1.82 at $32^{\circ}$ of the angle of stall respectively. 3.$C _{LX}$ of board with accessories is smaller 10~12% than that of only the main plate, and the angle of stall is almost same. 4. $C _{LX}$ and the angle of stall of the three-slot cambered board with accessories are greater 20% and $10^{\circ}$ than that of the simple cambered board respectively.

• Journal of the East Asian Society of Dietary Life
• /
• v.8 no.3
• /
• pp.271-279
• /
• 1998

This study was conducted to compare the serum composition and urinary excretion in four institutional groups and the effects of intakes of good foods and harmful foods according to the Sasang constitiution for a short time on serum and ruine compositon. The contitutions of 33 female stucdents were classified by O-ring test and muscular strength test according to the Sasang constitution, The number of each institutional group was So-yang-in 11, So-em-in 10 and Tae-em-in 12. No subject belonged to Tae-yang-in There were no significant differences among contitutional groups in the values of most serum composition and urinary excretion Serum levels of total cholesterol, glucose, calcium and phosphorus in Tae-em-in was the highest among groups and the level of albumin and total protein in So-em-in was highest. The values of serum compositions changed after the 33 subjects took good foods and then harmful foods according to The Sasang constitution for a short time(5 days). Dietary behavior of the subjects had some effects among the constitutional groups in the values of most serum composition and urinary excretion. But the effects of dietary behavior on the serum composition and urinary excretion showed various trends in the four institutional groups.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2004.11a
• /
• pp.166-172
• /
• 2004

An underwater motion measurement system was constructed for applications to the model basin. A commercial motion capture system, FALCON of Motion Analysis Corp., which corrects automatically the distortion caused by refraction of the light passing through water and air, was adopted for underwater motion measurement. The modifications of FALCON system were performed: waterproofing camera housings, markers, connectors, and a new blue ring lighter. the accuracy of the motion measurement was obtained within the calibration error of 0.87mm in average and 0.89mm in standard deviation for the distance of 500mm between two markers on the calibration device. the volume of $2100mm(length)\times2100mm(breadth)\times2300mm(Height)$ was covered with 4 cameras of the underwater motion measurement system. For the performance verification, motion measurement test of a vertical mooring chain model excited at the top end was carried out. The 3D motions of mooring model were measured with variable amplitude and period of the forced excitation. Higher order motions of the mooring model were observed as the excitation period decreases. the performance of the system was verified by successfully measuring 3D motion of mooring model.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.10
• /
• pp.1412-1416
• /
• 2014

We report thin-film organic moisture barriers based on polystyrene(PS) laminates deposition by PECVD for an encapsulation of OLEDs. The organic polystyrene thin-film has the benzene ring structure and high hydrophobic characteristics and it was polymerized by PECVD in dry process. Life time properties of Ca test were obtained 32 minutes at the RF 100W process conditions. From the AFM test, the roughness of multi-layer thin-film was more excellent rather than that of a single-layer thin-film. In addition, 5 layers of the multi-layer film properties were obtained 45 minutes. So that the optical and electrical properties were not affected with these plasma polymerized organic thin-film encapsulation. For life time improvement, the inorganic $Al_2O_3$ thin-film were deposited 5nm using ALD atomic layer deposition. The WVTR(Water Vaper Transmission Rate) value of hybrid thin-film encapsulation in the optimum process conditions was resulted by less than $10-3g/m^2/day$. From the results of experiment, plasma polymerized hybrid encapsulation was suggested as the flexible display applications.

• Tribology and Lubricants
• /
• v.11 no.4
• /
• pp.28-34
• /
• 1995

PTFE has good mechanical and chemical stability at wide temperature range, and more over, shows a low value of friction coefficient. On the other hand, it shows cold flow and high wear rate. However, these short comings can be overcome by adding various fillers. In this experiment, PTFE and polyimide powder were mixed into composite and its tribological characteristics was investigated. 100% polyimide was also tested for comparison. The countefface material was a stainless steel (SUS304). Friction and wear tester of ring-on-block type was used at room temperature and under atmosphere. After the wear test, the worn surfaces were examined by optical microscope. The test results show that PTFE-polyimide composite generates. the wear transfer film on both sides of the friction surfaces, and, the friction coefficient and the wear rates are relatively low. 100% polyimide generated little wear transfer films, showed high friction and wear rates, and also showed some problems of vibration and noise. It even damaged the stainless steel countefface. It was concluded that 100% polyimide does not generate transfer film well because its shear resistanbe is high and it stickslips, thus, friction coefficients and wear rates are high. In case of PTFE-polyimide composite, on the other hand, transfer film containing sufficient PTFE adheres and remains on both wear surfaces well enough because PTFE has low shear resistance. Polyimide particles in the composite were proved to be able to bear normal load and does not show stick-slip because they are covered with transfer film containing much PTFE.

• Journal of Korean Society of Transportation
• /
• v.13 no.1
• /
• pp.185-203
• /
• 1995

The purpose of this paper is to develop a microscopic traffic simulation model which is able to both analyze and the evaluate signlaized urban network and to verify its usefulness in comparison with the other model which has alfeady been released. This simulation model adopts the General Motor's 5th model for car-following and introduces an unique lanechanging rule using acceptable gap. It analyzes single and dual-ring signal phases and generates detector information . So it could be applied to dynamic route guidance systems as wel as real time signal control systems. The results derived from Netsim and the observed data from the real network have been used to test the validit of the proposed model. The result of the test has shown that there are no significant differences between the NETSIM model and the proposed model in estimating travel speed and stopped delay. In optimum offset estimatin , it has shown the same results with NETSIM. the measure of effectiveness , however, derived from this model is slightly better than that of the real network situation. This may be due to the fact that the proposed model does not take into account side frictions from interferences and obstacles.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.03a
• /
• pp.871-876
• /
• 2008

The blade vibration problem of bladed disk is the most critical subject to consider since it directly affects the stable performance of the engine as well as life of the engine. Especially, due to complicated vibration pattern of the bladed disk, more effort was required for vibration analysis and test. The research of measuring the vibration of the bladed disk, using NSMS(Non-intrusive stress measurement) instead of Aeromechanics testing method requiring slip ring or telemetry system with strain gauge, was successful. These testing can report the actual stresses seen on the blades; detect synchronous resonances that are the source of high cycle fatigue(HCF) in blades; measure individual blade mis-tuning and coupled resonances in bladed disks. In order to minimize the error being created due to heat expansion, the tip timing sensor is installed parallel to the blade trailing edge, yielding optimal result. Also, when working on finite element analysis, the whole bladed disk has gone through three-dimensional analysis, evaluating the family mode. The result of the analysis matched well with the test result.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.11a
• /
• pp.273-276
• /
• 2008

A Through Bulkhead Initiation Module(TBIM) has been designed which guarantees the seal property without using O-ring. The TBIM works as the shock wave generated by a donor charge transmits to the acceptor charge. The structural safety of TBIM housing has been calculated via modeling analysis, and the ignition performance has been proved by 10 cc closed bomb test. The reliability analysis has been made using Probit method on the base of performance test results. According to the reliability analysis the bulkhead thickness of TBIM which is the most important design parameter has been determined.