• Proceedings of the KIPE Conference
• /
• 2019.07a
• /
• pp.307-308
• /
• 2019

The Pohang Light Source (PLS) - II is a 3 GeV third-generation synchrotron radiation facility. To inject electron beam from LINAC, a kicker modulator system and kicker magnets are installed in the PLS-II storage ring tunnel. The injected beam then falls into the storage ring beam dynamic aperture. This paper describes the design and implementation of the solid-state kicker modulator for PLS-II. The solid-state kicker modulator is consisted of high voltage solid state switch stacks. the technical considerations of the solid-state switch stacking for kicker modulator is discussed. The achieved capability of the solid-state kicker modulator demonstrates that is fulfills the design requirement of providing half-sine pulsed current of 10kA (peak), 6us (Base-width), with jitter < 2ns (Standard deviation). simulation and experimental results are presented to demonstrate the performance of the solid-state kicker modulator.

• Applied Chemistry
• /
• v.17 no.1
• /
• pp.21-24
• /
• 2013

High performance count-current flow in packedtower design. Column that packed with Montz packing regular and dumped packing with Pall Ring, Hiflow Ring and Hackette have been represented high performance in vaccum rectification and absorption. The new correlating of these relationship based on the numerous results has been developed for process calculation and design. The results of laboratory or experimental pilot plant can be adopted directly for scale-up.

• Geotechnical Engineering
• /
• v.14 no.5
• /
• pp.5-16
• /
• 1998

2-D numerical methods have been applied to analyze the stability of tunnels because of computation efficiency, though the ground around the tunnel under construction shows 3-D reformational behaviour due to the transverse and longitudinal arching effects. Load distribution factors are introduced to the 2-D analysis for the consideration of the effects of the tunnel advance in three dimensions. The load distribution factors influence significantly the ground deformation and the load of primary supports like shotcrete and rockbolts. According to the previous studies for 3-D numerical studies. it was shown that load distribution factors were heavily dependent on the ground deformational properties, tunnel size and the advance length of a tunnel. However, as the quantitative methods evaluating the factors have not been presented yet, constant values have been assigned to the factors for 2-D analysis even if the conditions for tunnel design are different. Accordingly, this paper presents the method to evaluate quantitatively the load distribution factors through the regression analysis of 3-D analysis data on 72 design cases. Also, new modification to the load distribution factors are suggested for the ring-cut excavation method because the conventional 2-D analysis is not able to consider the support effects of the core left on the tunnel face.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.7
• /
• pp.796-808
• /
• 2007

In this paper, two novel compact microstrip bandstop filters using complimentary split ring resonators(CSRRs) and spiral resonators is proposed. The first one is the bandstop filter using an array of CSRRs etched on the center line of a microstrip. The bandstop is due to the presence of negative effective permittivity and positive permeability near resonant frequency which prevent the wave propagation. The second on is the bandstop filter using an array of spiral resonators etched on the center line of a microstrip. The bandstop is due to the self-resonance of spiral circuit. We have achieved controllable resonance frequency and bandwidth, super compact dimension, low insertion losses in the passband and high level of rejection in the stopband with sharp cutoff. The electrical sizes of two proposed filter are very small. Additionally, they can be easily fabricated and compatible with MMIC or PCB technology.

• Journal of KIISE:Computer Systems and Theory
• /
• v.26 no.11
• /
• pp.1305-1317
• /
• 1999

NUMA 구조는 원격 메모리에 대한 접근이 불가피한 구조적 특성 때문에 상호 연결망이 성능을 좌우하는 큰 변수가 된다. 기존에 대중적으로 사용되던 버스는 물리적 확장성 및 대역폭에서 대규모 시스템을 구성하는 데 한계를 보인다. 이를 대체하는 고속의 지점간 링크를 사용한 링 구조는 버스가 가지는 확장성 및 대역폭의 한계라는 단점을 개선하였으나, 많은 클러스터가 연결되는 경우에는 전송 지연시간이 증가하는 문제점을 가지고 있다. 본 논문에서는 스누핑 프로토콜이 적용된 링 구조에서 클러스터 개수 증가에 따른 지연시간 증가의 문제점을 보완하기 위해 계층적 링 구조로의 확장을 제안하고, 이 구조에 효과적인 캐쉬 일관성 프로토콜을 설계하였다. 전역 링과 지역 링을 연결하는 브리지는 캐쉬 프로토콜을 관리하며 이 프로토콜에 의해 지역 링의 부하를 줄일 수 있도록 트랜잭션을 필터링하는 역할도 담당함으로써 시스템의 성능을 향상시킨다. probability-driven 시뮬레이터를 통해 계층적 링 구조가 시스템의 성능 및 링 이용률에 미치는 영향을 알아본다. Abstract Since NUMA architecture has to access remote memory, interconnection network performance determines performance of NUMA architecture. Bus, which has been used as popular interconnection network of NUMA, has a limit to build a large-scale system because of limited physical scalability and bandwidth. Ring interconnection network, composed of high-speed point-to-point link, made up for bus's defects of scalability and bandwidth. But, it also has problem of increasing delay as the number of clusters is increased. In this paper, we propose a hierarchical expansion of snoop-based ring architecture in order to overcome ring's defects of increasing delay. And we also design an efficient cache coherence protocol adopted to this architecture. Bridge, which connects local ring and global ring, maintains cache coherence protocol and does snoop-filtering which reduces local ring and cluster bus utilization. Therefore bridge can improve performance of this system. We analyze effects of hierarchical architecture on the performance of system and utilization of point-to-point links using probability-driven simulator.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.2
• /
• pp.273-279
• /
• 2013

In this paper, a novel split ring resonator is proposed for improvement of phase noise characteristics that is weak point of oscillator using planar type microstrip line resonator, and oscillator for 5.8GHz band is designed using proposed split ring resonator. At the fundamental frequency of 5.8GHz, 7.22dBm output power and -83.5 dBc@100kHz phase noise have been measured for oscillator with split ring resonator. The phase noise characteristics of oscillator is improved about 9.7dB compared to one using the general ${\lambda}$/4 microstrip resonator. Because it is possible that varactor diode or lumped capacitor is placed on the gaps of split ring resonator, resonant frequency can be controlled by bias voltage. We can design voltage controlled oscillator using proposed split ring resonator. Thus, due to its simple fabrication process and planar type, it is expected that the technique in this paper can be widely used for low phase noise oscillators for both MIC and MMIC applications.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.8 no.2
• /
• pp.10-17
• /
• 2004

The results of the combustion performance tests of gas generator which supplies hot gas into the turbine of turbo-pump for liquid rocket engine and uses LOx and kerosene as propellant are described. The gas generator consists of a injector head with F-O-F impinging injector, a water cooled combustion chamber, a gas torch igniter, a turbulence ring and an instrument ring. The effect of turbulence ring and combustion chamber length on performance of gas generator are investigated. The ignition and combustion at design point are stable and the pressure and gas temperature at gas generator exit meets the target. The turbulence ring installed at middle of chamber effectively mixes hot gas with cold gas and the effect of residence time of hot gas in gas generator on combustion efficiency is small. Test results show that the main parameter controlling the gas temperature at gas generator exit is overall O/F ratio.

• International Journal of Fluid Machinery and Systems
• /
• v.9 no.3
• /
• pp.194-204
• /
• 2016

Floating ring seals offer an opportunity to reduce leakage flows significantly in rotating machinery. Accordingly, they have been applied successfully to rotating machinery within the last several decades. For rocket turbopump applications, fundamental behavior and design philosophy have been revealed. However, further work is needed to explore the rotordynamic characteristics associated with rotor vibrations. In this study, rotordynamic forces for floating ring seals under rotor's whirling motions are calculated to elucidate rotordynamic characteristics. Comparisons between numerical simulation results and experiments demonstrated in our previous report are carried out. The three-dimensional Reynolds equation is solved by the finite-difference method to calculate hydrodynamic pressure distributions and the leakage flow rate. The entrance loss at the upstream inlet of the seal ring is calculated to estimate the Lomakin effect. The friction force at the secondary seal surface is also considered. Numerical simulation results showed that the rotordynamic forces of this type of floating ring seal are determined mainly by the friction force at the secondary seal surface. The seal ring is positioned almost concentrically relative to the rotor by the Lomakin effect. Numerical simulations agree quite well with the experimental results.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.8
• /
• pp.1581-1586
• /
• 2012

In this paper, a novel resonator using ring type DGS is proposed for improvement of phase noise characteristics that is weak point of oscillator using planar type microstrip line resonator, and oscillator for 5.8GHz band is designed using proposed DGS resonator. The ring type DGS resonator is composed of DGS cell etched on ground plane under $50{\Omega}$ microstrip line. At the fundamental frequency of 5.8GHz, 7.6dBm output power and -82.7 dBc@100kHz phase noise have been measured for oscillator with ring type DGS resonator. The phase noise characteristics of oscillator is improved about 9.5dB compared to one using the general ${\lambda}/4$ microstrip resonator. Because it is possible that varactor diode or lumped capacitor is placed on the gaps of ring type DGS, resonant frequency can be controlled by bias voltage. We can design voltage controlled oscillator using proposed ring type DGS resonator. Thus, due to its simple fabrication process and planar type, it is expected that the technique in this paper can be widely used for low phase noise oscillators for both MIC and MMIC applications.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.24 no.2
• /
• pp.268-275
• /
• 2020

A lightweight hardware design of self-timed ring based true random number generator (TRNG) suitable for information security applications is described. To reduce hardware complexity of TRNG, an entropy extractor with feedback structure was proposed, which minimizes the number of ring stages. The number of ring stages of the FSTR-TRNG was determined to be a multiple of eleven, taking into account operating clock frequency and entropy extraction circuit, and the ratio of tokens to bubbles was determined to operate in evenly-spaced mode. The hardware operation of FSTR-TRNG was verified by FPGA implementation. A set of statistical randomness tests defined by NIST 800-22 were performed by extracting 20 million bits of binary sequences generated by FSTR-TRNG, and all of the fifteen test items were found to meet the criteria. The FSTR-TRNG occupied 46 slices of Spartan-6 FPGA device, and it was implemented with about 2,500 gate equivalents (GEs) when synthesized in 180 nm CMOS standard cell library.