• Structural Engineering and Mechanics
• /
• v.21 no.2
• /
• pp.137-150
• /
• 2005

Dynamic analysis of dam-reservoir-foundation system is usually carried out by employing a simplified and approximate one-dimensional model to account for fluid-foundation interaction. The approximation introduced on this basis is examined thoroughly in this paper by comparing the method with the rigorous approach. It is concluded that the errors due to approximate method could be very significant both for horizontal and vertical ground motions.

• 제어로봇시스템학회:학술대회논문집
• /
• 1989.10a
• /
• pp.848-855
• /
• 1989

By structural comparison of process optimization strategies based on Simultaneous Modular Approach, they can be classified into two groups : the Sequential Module Based Approach and the Two-Tier Approach. The Sequential Module Based Approach needs rigorous models and a set of accurate solutions are guranteed. However, it requires large amount of computation time. In the Two-Tier Approach composed of rigorous and simplified models, optimization calculation uses simplified models, therefore comparatively smaller amount of computation time is required but the obtained solutions may not be accurate. These optimization problems were somewhat improved by the alternate application of the two strategies. In this study, improved optimization strategy is suggested, in which Jacobian Matrix is modified to accomodate the strong points of above mentioned strategies. The results of case study show that this approach is superior to the other strategies.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.8
• /
• pp.1091-1098
• /
• 2012

This paper describes frequency response and propagation characteristics considering semiconducting screen in distribution cables. In CIGRE WG 21-05, Simplified Approach(SA) and Rigorous Approach(RA) which can revise the permittivity considering semiconducting screen propose for more detailed EMTP model and frequency dependant analysis. In this paper, the frequency dependent characteristics of complex permittivity are variously analysed by cole-cole function of RA. The attenuation, propagation velocity and surge impedance according to frequency range(1 kHz to 500 MHz) and cable length are also analysed by SA and EMTP simulation in distribution cables. The propagation velocity considering semiconducting screen is slower, and it is saturated over the range of 1 MHz. The signal is significantly attenuated as frequency range is high.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.30 no.6_2
• /
• pp.593-605
• /
• 2012

LiDAR systems provide dense and accurate topographic information. A pre-requisite to achieving the potential accuracy of LiDAR is having a proper system calibration, which aims at estimating all the systematic errors in the system measurements and the mounting parameters relating the different components. This paper presents a rigorous and two approximate methods for LiDAR system calibration. The rigorous approach makes use of the LiDAR equation and the system raw measurements. The approximate approaches utilize simplified LiDAR equations using some assumptions, which allow for less strict requirements regarding the raw measurements. The first presented approximate method, denoted as quasi-rigorous, assumes that we are dealing with a vertical platform (i.e., small pitch and roll angles). This method requires time-tagged point cloud and trajectory position data. The second approximate method, denoted as simplified, assumes that we are dealing with parallel strips, vertical platform, and minor terrain elevation variations compared to the flying height above ground. Such method can be performed using the LiDAR point cloud only. Experimental results using a real dataset, whose characteristics deviate to some extent from the utilized assumptions in the approximate methods, are presented to provide a comparative analysis of the outcome from the introduced methods.

• Earthquakes and Structures
• /
• v.3 no.3_4
• /
• pp.533-548
• /
• 2012

Dynamic analysis of concrete gravity dam-reservoir systems is an important topic in the study of fluid-structure interaction problems. It is well-known that the rigorous approach for solving this problem relies heavily on employing a two-dimensional semi-infinite fluid element. The hyper-element is formulated in frequency domain and its application in this field has led to many especial purpose programs which were demanding from programming point of view. In this study, a technique is proposed for dynamic analysis of dam-reservoir systems in the context of pure finite element programming which is referred to as the wavenumber approach. In this technique, the wavenumber condition is imposed on the truncation boundary or the upstream face of the near-field water domain. The method is initially described. Subsequently, the response of an idealized triangular dam-reservoir system is obtained by this approach, and the results are compared against the exact response. Based on this investigation, it is concluded that this approach can be envisaged as a great substitute for the rigorous type of analysis.

• Journal of Welding and Joining
• /
• v.28 no.2
• /
• pp.39-46
• /
• 2010

IIn this study, used is the equivalent loading method based on the inherent strain to predict the welding deformation of panel members. Equivalent loads are computed from the inherent strain distribution around weld line, and then applied for the linear finite element analysis. Thermal deformation of panel members can be, of course, carried out through the rigorous thermal elasto-plastic analysis procedure but it is not practical in applying to predicting the welding deformation of large structures such as blocks found in a ship structure from view of computing time. The present equivalent load approach has been applied to flat plate model to verify the present approach, and to several curved plate models having the curvature in the welding direction to investigate the effect of the longitudinal curvature upon the weld-induced deformation. The results are compared with those by thermal elasto-plastic analysis. As far as the present results are concerned, it can be said that the present approach shows good agreement with the results by welding experiment and the rigorous thermal elasto-plastic analysis. The present approach has been also applied to predict the welding deformation of panel block as for application illustration to practical model.

• Structural Engineering and Mechanics
• /
• v.30 no.5
• /
• pp.619-645
• /
• 2008

This study presents the efficiency of simulating structural systems using a method that combines a simplified component model (SCM) and rigorous component model (RCM). To achieve a realistic simulation of structural systems, a numerical model must be adequately capturing the detailed behaviors of real systems at various scales. However, capturing all details represented within an entire structural system by very fine meshes is practically impossible due to technological limitations on computational engineering. Therefore, this research develops an approach to simulate large-scale structural systems that combines a simplified global model with multiple detailed component models adjusted to various scales. Each correlated multi-scale simulation model is linked to others using a multi-level hierarchical modeling simulation method. Simulations are performed using nonlinear finite element analysis. The proposed method is applied in an analysis of a simple reinforced concrete structure and the Reuipu Elementary School (an existing structure), with analysis results then compared to actual onsite observations. The proposed method obtained results very close to onsite observations, indicating the efficiency of the proposed model in simulating structural system behavior.

• Korean Journal of Optics and Photonics
• /
• v.10 no.4
• /
• pp.348-353
• /
• 1999

Ray-optics approach based on the rigorous coupled wave theory, called by the rigorous ray-optics method (RROM), is developed for the calculation of couling coefficients of waveguide grating devices. The coupling coefficients of several grating structures, such as rectangular, sinusoidal, triangle, and trapezoidal shapes, are determined by the RROM, and they are compared with those obtained by conventional methods of the ray-optics method (ROM) and the coupled mode method (CMM). In the case of rectangular gratings, the coupling coefficients is evaluated in detail by various depths and duty-cycles of the grating. We have found that the RROM gives more exact solutions for the coupling coefficients of even arbitrary shapes of diffractive waveguide grating devices than the other conventional methods.

• Proceedings of the IEEK Conference
• /
• summer
• /
• pp.276-280
• /
• 2004

This paper first takes advantage of a rigorous modal transmission-line theory (MTLT) to analyze the filtering properties of optical waves guiding by grating-assisted fiber couplers (GAFCs). The numerical results reveal that MTLT serves as a suitable and powerful approach to evaluate systematically the dispersion properties and the characteristics of optical power transfer in GAFCs.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.15 no.1
• /
• pp.261-267
• /
• 2015

The eigenvalue problems involving the diffraction of waves by multi-layered grating configurations can be explained by rigorous modal expansion terms. Such a modal solution can be represented by equivalent transmission-line networks, which are generalized forms of simple conventional circuits. This approach brings considerable physical insight into the grating diffraction process of the fields everywhere. In particular, the transmission-line representation can serve as a template for computational algorithms that systematically evaluate dispersion properties, radiation effects and other optical characteristics that are not readily obtained by other methods. To illustrate the validity of the present rigorous approach, the previous research works are numerically confirmed and the results agree well each other.