• 열처리공학회지
• /
• 제13권4호
• /
• pp.253-258
• /
• 2000

The present study aimed to develop the TRIP(transformation induced plasticity) aided high strength low carbon steel sheets using reverse transformation process. The cold-rolled 0.14C-6.5Mn steel was reverse-transformed by slow heating to intercritical temperature region and air cooling to room temperature. An excellant combination of tensile strength and elongation of $98.3kgf/mm^2$ and 44.4% appears. This combination comes from TRIP phenomena of retained austenite during deformation. The stability of retained austenite Is very Important for the good ductility and it depends on diffusion of carbon and manganese during reverse transformation. The air cooling after holding at intercritical temperature retards the formation of pearlite and provides the carbon enrichment in retained austenite, resulting the increase of elongation in cold-roiled TRIP steel.

• 열처리공학회지
• /
• 제16권4호
• /
• pp.205-210
• /
• 2003

Various types of high strength steel sheets were usually used for improving the automobile safety and fuel efficiency by reducing the vehicle weight. The present study aimed to develop the TRIP (transformation induced plasticity) aided high-strength low carbon steel sheets by using a reverse transformation process. The 0.1C-4~8Mn steels were reverse-transformed by slow heating to intercritical temperature region and then furnace cooled to the room temperature. Granular type retained austenite was observed in 4Mn steel and lath type retained austenite was also observed in 6~8Mn steel. The results show that the 6Mn steel under reverse transformed at $625^{\circ}C$ for 6 hrs has maximum elongation up to 39%. The optimum strength-elongation combination was 3,888 ($kg/mm^2{\times}%$) when the 8Mn steel was reverse transformed at $625^{\circ}C$ for 12 h.

• 열처리공학회지
• /
• 제12권4호
• /
• pp.313-319
• /
• 1999

The reverse transformation behavior was investigated by DSC analysis in thermomechanically processed Fe-30%Ni-0.35%C alloy. Upon increasing the heating rate from $5^{\circ}C/min$ to $80^{\circ}C/min$, the As point of the ausformed martensite was not changed and the As point of the marformed martensite decreased at reverse transformation. The Af points showed to be constant with increasing the heating rate both in the ausformed martensite and in the marformed martensite. With increasing the deformation degree, the As points of the ausformed martensite and the marformed martensite increased and the Af points appeared to be constant, structures. The enthalpy changes increased with increasing the heating rate, but decreased with increasing the deformation degree in both structures.

• 전자공학회논문지S
• /
• 제34S권2호
• /
• pp.52-62
• /
• 1997

To reconstruct the complete 3-D shape of an object, seveal range images form different viewpoints should be merged into a single model. The process of extraction of the transformation parameters between multiple range views is calle dregistration. In this paper, we propose a new algorithm to find the transformation parameters between multiple range views. Th eproposed algorithm consists of two step: initial estimation and iteratively update the transformation. To guess the initial transformation, we modify the principal axes by considering the projection effect, due to the difference fo viewpoints. Then, the following process is iterated: in order to extract the exact transformation parameters between the range views: For every point of the common region, find the nearest point among the neighborhood of the current corresponding point whose correspondency is defined by the reverse calibration of the range finder. Then, update the transformation to satisfy the new correspondencies. In order to evaluate the performance the proposed registration algorithm, some experiments are performed on real range data, acquired by space encoding range finder. The experimental results show that the proposed initial estimation accelerate the following iterative registration step.

• 한국재료학회지
• /
• 제14권2호
• /
• pp.126-132
• /
• 2004

The high strength steel sheets has been widely used as the automobile parts to reduce the weight of a vehicle. The aim of this research is to develop the TRIP aided high strength low carbon steels using reverse transformation process. The 0.15C-4Mn and 0.15C-6.5Mn steel sheets were reversely transformed by slow heating to intercritical temperature region and air cooling to room temperature. The stability of retained austenite depends on the enrichment of carbon and manganese by diffusion during the reverse transformation. The amount of retained austenite formed after reversely transformed at $645^{\circ}C$ for 12 hrs. was about 46vol.% in hot rolled 0.lC-6.5Mn steel. The change in volume fraction of retained austenite with a holding temperature was consistent with the changes in elongation and the strength-ductility combination. The tendency of tensile strength to increase with increasing the holding temperature was due to the decrease of retained austenite after cooling from the higher temperature of $670 ^{\circ}C$. The maximum strength-ductility combination was about 4,250 kg/$\textrm{mm}^2$ㆍ% when the hot rolled 0.lC-6.5Mn steel was reversely transformed at $645^{\circ}C$ for 12 hrs.

• 정보처리학회논문지D
• /
• 제10D권5호
• /
• pp.845-858
• /
• 2003

1980년대 이후, 소프트웨어 위기에 대응하기 위한 다양한 소프트웨어 공학적 기법들이 출현하기 시작 하였고, 현재 소프트웨어의 질적 항상 및 생산성 향상을 꾀하기 위한 개발 지침으로 소프트웨어 개발 프로세스를 적용하는데 관심이 집중되어지고 있다. 그러나 대부분의 방법론들이 앞으로 구축한 새로운 시스템의 재사용성 확보에 치중할 뿐, 기존의 레거시 시스템 자원을 재사용하여 새로운 시스템을 구축하는 재공학 방법은 지원하지 못하고 있는 실정이다. 본 논문에서는 레거시 시스템의 효율적 진화를 위한 재공학 프로세스(Reengineering Process)로 RUP를 확장, 커스터마이징하여 구성한 RUP+re을 제시한다. RUP+re는 Small-h 모델을 바탕으로 크게 역공학 워크플로우(Reverse Engineering Workflow), 변환 워크플로우(Transformation Workflow), 진화 워크플로우(Evolution Workflow)로 구성되어진다. RUP+re의 각 워크플로우와 세부스텝을 제공하고 재공학 사례 연구론 통하여 실질적으로 프로세스를 검증함으로서 레거시 시스템 자원의 진화론 위한 소프트웨어 재공학 프로세스 구축에 효율적인 지침을 제공한다.

• 열처리공학회지
• /
• 제8권1호
• /
• pp.12-23
• /
• 1995

In this a set of constitutive equation relevant to the analysis of thermo-elasto-plastic materials with phase transformation during quenching process was presented on the basis of continuum thermo-dynamic. In calculating the transient thermal stresses, temperature between coolant and specimen(SM45C) surface was determined from the heat transfer coefficient. A calculation was made for specimen with 40mm in diameter quenched in coolant from $820^{\circ}C$ and the results are as follow. Stresses at starting point of transformation always show the maximum tensile value. Reverse of stresses takes place after completion of transformation of inner part at specimen.

• Journal of Mechanical Science and Technology
• /
• 제20권1호
• /
• pp.19-28
• /
• 2006

This paper describes rapid prototyping (RP) and reverse engineering (RE) application for orthopedic surgery planning to improve the efficiency and accuracy of the orthopedic surgery. Using the symmetrical characteristics of the human body, CAD data of undamaged bone of the injured area are generated from a mirror transformation of undamaged bone data for the uninjured area. The physical model before the injury is manufactured from Poly jet RP process. The surgical plan, including the selection of the proper implant, pre-forming of the implant and decision of fixation positions, etc., is determined by a physical simulation using the physical model. In order to examine the applicability and efficiency of the surgical planning technology, two case studies, such as a distal tibia comminuted fracture and an iliac wing fracture of pelvis, are carried out. From the results of the examination, it has been shown that the RP and RE can be applied to orthopedic surgical planning and can be an efficient surgical tool.

• 한국IT서비스학회지
• /
• 제2권1호
• /
• pp.111-121
• /
• 2003

This paper intents to suggest the re-engineering methodology to transform and integrate the legacy systems to new system in modern environment. While existing reverse engineering and re-engineering approaches have focused on analyzing and maintaining the source code of program. our methodology can provide the procedures and techniques for evolving into new system by recovering the reverse engineering informations and transforming them into component informations. Our methodology for componentization of legacy system is consisted of plan step, reverse engineering step, componentization step, and delivery step, and we describes activities and detail procedures about each step.

• 한국재료학회지
• /
• 제15권2호
• /
• pp.115-120
• /
• 2005

The aim of this research is to develop the TRIP aided high strength low carbon steels using reverse transformation process. The $4\~8\%$ Mn steel sheets were reversely transformed by slow heating to intercritical temperature region and furnace cooling to room temperature. The stability of retained austenite depends on the enrichment of carbon and manganese by diffusion during the reverse transformation. The amount of retained austenite formed after reversely transformed at $625^{\circ}C$ for 6 hrs was about $50\;vol.\%$ in the $8\%Mn$ steel. The change in volume fraction of retained austenite with a holding temperature was consistent with the changes in elongation and the strength-ductility combination. The maximum strength-ductility combination of 40,000 $MPa{\cdot}\%$ was obtained when the $8\%Mn$ steel reversely transformed at $625^{\circ}C$ for 12 hrs. However, it's property was significantly decreased at higher holding temperature of $675^{\circ}C$ resulting from the decrease of ductility.