• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.35 no.3
• /
• pp.335-342
• /
• 1999

The purpose of present research is to develop and efficient numerical method for the calculation of potential flow and predict the wave-making resistance for the application to ship design of tuna purse seiner. Havelock was considered the wave resistance of a post extending vertically downwards through the water from the surface, its section by a horizontal plane being the same at all depths and having its breadth small compared with its length. This enables us to elucidate certain points of interest in ship resistance. However, the ship has not infinite draft. So, the problem which is investigated ind detail in this paper is the wave resistance of a mathematical quadratic model in a uniform stream. The paper deals with the numerical calculation of potential flow around the series 60 with forward velocity by the new slender ship theory. This new slender ship theory is based on the asymptotic expression of the Kelvin-source, distributed over the small matrix at each transverse section so as to satisfy the approximate hull boundary condition due to the assumption of slender body. The numerical results using the panel shift method and finite difference method are compared with the experimental results for wigley mono hull. There are no differences in the wave resistance. However, it costs much time to compute not only wave resistance but also wave pattern over some range of Froude numbers. More improvements are strongly desired in the numerical procedure.

• Applied Microscopy
• /
• v.42 no.4
• /
• pp.207-211
• /
• 2012

We examined the electrical properties and microstructure of NiO produced using a sol-gel method and Ni nitrate hexahydrate ($Ni[NO_3]_2{\cdot}6H_2O$) to investigate if this NiO thin film can be used as an insulator layer for resistance random access memory (ReRAM) devices. It was found that as-prepared NiO film was polycrystalline and presented as the nonstoichiometric compound $Ni_{1+x}O$ with Ni interstitials (oxygen vacancies). Resistances-witching behavior was observed in the range of 0~2 V, and the low-resistance state and high-resistance state were clearly distinguishable (${\sim}10^3$ orders). It was also demonstrated that NiO could be patterned directly by KrF eximer laser irradiation using a shadow mask. NiO thin film fabricated by the sol-gel method does not require any photoresist or vacuum processes, and therefore has potential for application as an insulating layer in low-cost ReRAM devices.

• Progress in Superconductivity and Cryogenics
• /
• v.14 no.3
• /
• pp.23-27
• /
• 2012

This paper aims to evaluate the feasibility of using no-insulation High Temperature Superconducting (HTS) coil in persistent current mode system. A HTS coil in persistent current mode system usually includes one or more non-superconducting joints in its circuit. And the current decaying rate of the coil is affected by the resistance of joint in persistent current circuit. If the resistance of joint is large, decaying rate of the current drastically increases. Therefore, reducing the joint resistance of the HTS coil is very important in persistent current mode system. In this paper, the no-insulation HTS coil is suggested as a way to reduce the joint resistance with the embedded parallel contact resistance naturally made by no-insulation winding method. Two small coils are fabricated with insulation and no-insulation winding method, and persistent current mode system experiment of each coil is preformed and analyzed.

• KEPCO Journal on Electric Power and Energy
• /
• v.6 no.2
• /
• pp.151-155
• /
• 2020

In this paper, a new experimental method to determine the thermal resistance of building wall was proposed by improving the heat flow method (HFM) based on the air-surface temperature ratio theory. This technique measures the thermal resistance of the wall excluding the inner and outer surface heat transfer resistance. Unlike conventional HFM, this value can be compared directly with the theoretical reference value. Its performance was verified using three mock-up structures with a theoretical thermal transmittance of 0.5, 3.3, and 0.18 W/㎡·K respectively. After measuring the variations in the temperature and heat transfer rate of the mock-ups for 383 hours, the thermal transmittances were determined to be 0.47, 3.10, and 0.18 W/㎡·K, which corresponded to errors of 5.2, 6.2 and 0.5%, respectively, compared to the theoretical values. It was concluded that this technique can directly compare the thermal resistance of the wall between the existent stage and initial stage after construction.

• Transactions of the Society of Information Storage Systems
• /
• v.3 no.4
• /
• pp.160-166
• /
• 2007

In this paper, the measured electrical resistance method is proposed to analyze the ramp-tab contact during the load/unload (L/UL) process. Since this method supplies the voltage change due to the resistance change, we can easily and conveniently identify the ramp-tab contact from the acoustic emission (AE) signal. At first, we carefully deposit the conductive material on the surface of the conventional ramp by sputtering method. The ratio frequency (RF) magnetron co-sputtering system is applied to accomplish the deposited double-layers on the ramp surface. One layer is the stainless steel for the conductive layer and the other is the titanium layer for the cohesive function between the ramp surface and the stainless steel layer. In order to guarantee the stiffness and damping properties of the original ramp, the deposited conductive layer is intended to have very thin thickness. After integration the proposed ramp device into the L/UL system and networking the electrical resistance circuit, the L/UL performance is experimentally evaluated by comparing the measured electrical resistance signal and AE signal.

• Journal of the Society of Naval Architects of Korea
• /
• v.59 no.6
• /
• pp.393-399
• /
• 2022

During the ship hull design process, resistance performance estimation is generally calculated by simulation using computational fluid dynamics. Since such hull resistance performance simulation requires a lot of time and computation resources, the time taken for simulation is reduced by CPU clusters having more than tens of cores in order to complete the hull design within the required deadline of the ship owner. In this paper, we propose a method for estimating resistance performance of ship hull by simulation using a graph neural network. This method converts the 3D geometric information of the hull mesh and the physical quantity of the surface into a mathematical graph, and is implemented as a deep learning model that predicts the future simulation state from the input state. The method proposed in the resistance performance experiment of simple hull showed an average error of about 3.5 % throughout the simulation.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.4 no.1
• /
• pp.3-12
• /
• 1967

This study has been endeavored to deposit resistance films of tin oxide on the cylindrical Pyrex glass rods. In this report, at first an outline of the film formation is described and later some electrical properities of the resistance films manufactured through new method is discussed in detail. Because the new method which is called, "Chemical Vapour Reaction Process", is not only easy to get stable resistance films, but also doesn't need vacuum systtem, it seems to be a promising fundamental process to go into flow system mass production. Electrical properties of resistance films made by the new mathod are similar to or surpassing those by provious method (for example splay method). The top data thus obtained shows that surface resistivity is 25ohm/sq. with 12 ppm in temperature coefficient of resistor. resistor.

• Journal of Energy Engineering
• /
• v.20 no.1
• /
• pp.21-25
• /
• 2011

In order to monitor a rotating cylindrical separator for radioactive waste, an electrical resistance method is proposed and its mathematical model is investigated. In a rotating radioactive waste separator, the electrical resistance between a pair of electrodes mounted on the inner wall of the vessel is related to the thickness of annular region of insoluble particle formed around the periphery and the concentration of the insoluble particle in that region. This work presents an analytical relationship among the aforementioned parameters based on a two-dimensional solution to the electrical potential equation and an empirical conductivity-concentration relation. Also, the feasibility of electrical resistance method for monitoring rotating cylindrical separators is discussed.

• Research in Plant Disease
• /
• v.21 no.1
• /
• pp.20-23
• /
• 2015

A sequential planting method was developed to screen rice plants with durable resistance against rice blast in a short time, and applied for several years in Korean rice breeding program. In this study, we showed the advantages of a sequential planting method compared to other pathogenicity tests. The correlation analysis among three pathogenicity tests and other factors demonstrated that durable resistance depended on the average of diseased leaf area and the number of compatible pathogens. Significant correlations were found in the nursery test but not in the field test result. In addition, we traced changes in the pathogen population during sequential planting stages through re-isolation of the pathogen. The portion of compatible pathogens was increased during sequential planting. Through this study, we provide an effective sequential planting method and direction of durable resistance in a breeding program.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.19 no.3
• /
• pp.119-126
• /
• 2005

Electrical resistance tomography(ERT) maps resistivity values of the soil subsurface and characterizes buried objects. The characterization includes location, size and resistivity of buried objects. In this paper, Gauss-Newton, truncated least squares(TLS) and simultaneous iterative reconstruction technique(SIRT) methods are presented for the solution of the ERT image reconstruction. Computer simulations show that the spatial resolution of the reconstructed images by the TLS approach is improved as compared to those obtained by the Gauss-Newton and SIRT method.