• Carbon letters
• /
• 제4권2호
• /
• pp.57-63
• /
• 2003

In polymer precursor based activated carbon, the structure of starting material is likely to have profound effect on the surface properties of end product. To investigate this aspect phenolic resins of different types were prepared using phenol, mcresol and formaldehyde as reactants and $Et_3N$ and $NH_4OH$ as catalyst. Out of these resins two resol resins PFR1 and CFR1 (prepared in excess of formaldehyde using $Et_3N$ as catalyst in the basic pH range) were used as raw materials for the preparation of activated carbons by both chemical and physical activation methods. In chemical activation process both the resins gave activated carbons with high surface areas i.e. 2384 and 2895 $m^2/g$, but pore size distribution in PFR1 resin calculated from Horvath-Kawazoe method, contributes mainly in micropore range i.e. 84.1~88.7 volume percent of pores was covered by micropores. Whereas CFR1 resin when activated with KOH for 2h time, a considerable amount (32.8%) of mesopores was introduced in activated carbon prepared. Physical activation with $CO_2$ leads to the formation of activated carbon with a wide range of surface area (503~1119 $m^2/g$) with both of these resins. The maximum pore volume percentage was obtained in 3-20 ${\AA}$ region by physical activation method.

• Journal of the Korean Wood Science and Technology
• /
• 제39권2호
• /
• pp.179-186
• /
• 2011

In an effort to understand the hydrolytic degradation process of cured urea-formaldehyde (UF) resins responsible for the formaldehyde emission of wood-based composite panels, this study analyzed the influence of acid hydrolysis on the morphology of cured UF resins with different formaldehyde/urea (F/U) mole ratios such as 1.6, 1.4, 1.2 and 1.0. Field emission-scanning electron microscopy (FE-SEM) was employed to observe both exterior and fracture surfaces on thin films of cured UF resins before and after the etching with hydrochloric acid as a simulation of the hydrolytic degradation process. FE-SEM images showed that the exterior surface of cured UF resin with the F/U mole ratio of 1.0 had spherical structures after the acid hydrolysis while the other cured UF resins were not the case. However, the fracture surface observation showed that all the samples possessed spherical structures in the cured state of UF resins although their occurrence and size decreased as the F/U mole ratio increased. For the first time, we found the spherical structures in cured UF resins of higher F/U mole ratio of 1.4. After the acid hydrolysis, the spherical structures became a much predominant at the fracture surface. These results indicated that the spherical structures in cured UF resinswere much more resistant to the hydrolytic degradation by the acid than amorphous region.

• Design & Manufacturing
• /
• 제2권4호
• /
• pp.54-61
• /
• 2008

Warpage, which is one of the molding trouble, acts as possible factor which results in defect in assembly. In this study, a mold was designed to produce specimens with rib parallel to flow direction, specimens with rib perpendicular to flow direction and specimens without rib. This work researched change of warpage according to injection molding condition such as injection pressure, packing pressure, packing time, resin temperature, mold temperature in non-crystalline resins(PC, ABS), crystalline resins(PP, PA66), and 30% glass fiber reinforced-resins(PC, ABS, PP, PA66).Specimens with rib and Crystalline resins show more warpage than specimens without rib and non-crystalline resins, respectively. Glass fiber reinforced-resins and specimens with rib parallel to flow direction show smaller warpage than conventional resins and specimens with rib perpendicular to flow, respectively. Specimens with rib and specimens without rib show reduced warpage as packing time increases. In addition, warpage increase as resin temperature increases. It is found that CAE shows similar tendency with experiment as packing time, resin temperature. when the rib is caused, warpage will reduce and prevent the transformation. product of a irregular form occurs warpage. In the study It'll be basic data that product occurs warpage, preferablity.

• 대한치과기공학회지
• /
• 제35권2호
• /
• pp.97-103
• /
• 2013

Purpose: The purpose of this study was to investigate the effect of addition of fiber glass on the physical properties of silanized fiber mesh and non silanized mesh of denture base resins. Methods: The denture base resins were used in this study heat curing acrylic resins(Vertex Rs, Lucitone 199, $20{\times}80mm$) and fiber glass(SES, Green B&D co., Ltd, $20{\times}80mm$) were used as reinforcement. The specimens were stored in distilled water at $37{\pm}2^{\circ}C$ for 72 hours before test. Bending strength and tensile strength were measured by an universal testing machine(Instron 4301, Instron Corp.). Penetration distribution on fiber was observed by scanning electron microscopy(JSM 840A, Jeol Ltd). Results: The bending strength and modulus were increased by 30% after adding fiber glass on denture base resins. Tensile strength showed significant increasing by adding fiber glass on denture base resins. Conclusion: In this study, Addition of silanized fiber in denture base resins were improved physical properties. we confirmed the fiber glass possibility of the replacement about conventional materials.

• 보존과학연구
• /
• 통권20호
• /
• pp.139-154
• /
• 1999

We tested to obtain the excellent Epoxy resins on the property of matter. Existing Epoxy resins is tested to regulate the viscosity, color and hardening time etc. Benzen-ring structure of Bisphenol A type (AY 103) is replaced by Hydrogenated B.P.A type. And hardener is replaced by Polyoxyalkylene Amine. So we are developed into the two resins(L-30, L-40).To know if this Epoxy resins was fitted to repairing and restoration of stone cultural properties. Three kinds of Epoxy resins (AY 103, L-30, L-40) are tested on the artificial weathering test, freezing-melting test, exposure test etc. As a result of test, L-30 is less the discoloration than that of other Epoxy resins and was superior to the excellent property of matter.

• 대한치과의료관리학회지
• /
• 제11권1호
• /
• pp.38-46
• /
• 2023

Composite resins, commonly used in clinical practice, have been developed to improve aesthetics to obtain smooth surfaces. Although the restored composite resin has a smooth surface, it gradually becomes rough over time. Therefore, this study measured glossiness to evaluate the surface of various composite resins and attempted to evaluate the maintenance of glossiness of composite resins by observing surfaces that change to roughness. Specimens were produced using resin used in clinical practice: Gradia direct anterior (GA), Tetric N-Ceram (TN), Ceram.X Sphere TEC one (CX), Filtek Z350XT (FT), Estelite sigma quick (ES). After creating a smooth surface with slide glass, five locations were randomly selected to measure surface gloss, and the average was the representative value of the specimen. Roughness was applied to the specimen under water pouring at the same speed and pressure using SiC paper #2400, 1200, and 400. The gloss unit of different SiC papers was measured. To evaluate the gloss unit and gloss retention between composite resins, one-way analysis of variance and Tukey multiple comparisons test were used. As a result of the study, there was a difference in gloss unit of specimens produced under the same conditions. Although the degree differed depending on the composite resin, there was also a difference in gloss retention. Based on the findings, composite resins show differences in gloss due to their different characteristics. Ceram.X Sphere TEC one (CX) showing the lowest gloss retention and Estelite sigma quick (ES) showing the highest.

• Journal of the Korean Wood Science and Technology
• /
• 제39권3호
• /
• pp.221-229
• /
• 2011

목질계 판상재료 생산을 위하여 현재 주로 사용되고 있는 석유화학계 접착제는 원유의 가격 상승과 포름알데히드 방산과 같은 문제로 인해 대체 접착제에 대한 개발 필요성이 오래전부터 대두되었다. 본 연구에서는 석유화학계 접착제를 대체하기 위하여 바이오 디젤 부산물인 유채박의 효소 가수분해를 통해 접착제를 조제하고, 이 접착제를 단판적층재 제조에 적용한 후 물리 및 기계적 특성을 조사하여 유채박의 단판적층재 제조용 접착제 제조를 위한 원료화 가능성을 확인하고자 수행하였다. 먼저 유채박 접착제 조제를 위하여 유채박을 4가지 효소의 조합을 통해 개량한 다음, phenol formaldehyde (PF) prepolymer와 혼합하여 접착제를 제조하고 이를 단판적층재 제조에 사용하였다. 제조된 단판적층재의 평균함수율과 내수성은 모두 KS의 기준을 만족시키는 것으로 나타났으며, 유채박 접착제의 열분석에서 pectinase 가수분해물로 조제한 접착제를 제외하고 페놀수지 접착제와 열경화 특성이 큰 차이를 보이지 않았다. 단판적층재의 휨강도는 페놀수지 접착제로 제조한 단판적층재보다 높거나 유사한 것으로 나타나 기존 석유화학계 접착제의 대체 접착제로써 가능성을 보여주었다. 추후 접착성능의 향상을 위해 적절한 유채박의 효소가수분해 조건에 대한 연구와 도포성능 개선에 대한 연구가 필요할 것으로 생각된다.

• Bulletin of the Korean Chemical Society
• /
• 제31권4호
• /
• pp.976-980
• /
• 2010

A series of arylacetylene resins with siloxane units were synthesized by the condensation reactions of m-diethynylbenzene magnesium reagents with various $\alpha,\omega$-bis(chloro)dimethylsiloxanes. These resins are liquids and are miscible with common organic solvents at room temperature. The structures of the resins were characterized by FT-IR, $^1H$ NMR, $^{13}C$ NMR, $^{29}Si$ NMR, and gel permeation chromatography (GPC). The thermal behaviors of the resins were examined with differential scanning calorimetry (DSC). These resins have good processability. They can be thermally cross-linked through the ethynyl groups to produce cured resins. The thermal and thermooxidative stabilities of the cured resins were studied by thermogravimetric analysis (TGA). The cured resins possess high thermal and thermooxidative stability. Their decomposition occurs at above $500^{\circ}C$ in both $N_2$ and air. With increasing the length of siloxane units in the resins, the thermal stability of the cured resins decreases in $N_2$. When the cured resins were sintered above $1450^{\circ}C$ under argon, hard and glassy SiOC ceramics were obtained. These SiOC ceramics have the decomposition temperatures at 5% weight loss above $800^{\circ}C$ in air.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1990년도 추계학술대회 논문집
• /
• pp.95-97
• /
• 1990

This study investigated electrical characteristic of solids and liquid epoxy resins by measuring dielectric breakdown and dielectric loss when epoxy resins were exposed to a mixing cure. It was found that mixing epoxy resins were superior to dielectric breakdown and hardness and has shorter curing time compare with those of pure liquid epoxy resins.

• 공업화학
• /
• 제31권3호
• /
• pp.310-316
• /
• 2020

테르펜 개질 페놀 수지는 타이어의 주행 안전성과 관련 있는 웨트 트랙션과 연비와 관련된 구름저항을 개선하기 위해 사용한다. 이 시험은 테르펜 개질 페놀 수지의 기본 구조가 각각 알파 피넨, 베타 피넨, 델타 리모넨으로 달리한 수지를 타이어 트레드 배합물에 첨가하여 알킬 페놀 수지의 배합물과 물성 차이를 비교하였다. 알킬 페놀 수지는 웨트 트랙션과 관련 있는 0 ℃에서 탄젠트 델타가 테르펜 개질 페놀 수지와 큰 차이가 없지만 구름저항과 관련 있는 80℃에서 탄젠트 델타가 높게 나타나 연비 개선 효과가 적었다. 테르펜 개질 페놀 수지 중 베타 피넨은 웨트 트랙션과 연비 개선 효과가 다른 수지에 비해 고르게 나타났으며, 델타 리모넨 수지는 웨트 트랙션 개선효과가 가장 좋았고, 인장강도 및 마모 성능은 알킬 페놀 수지가 비교적 높게 나왔다. 모든 테르펜 개질 수지는 구름저항에서 알킬 페놀수지보다 우수하여 연비 개선효과 좋다고 할 수 있으며, 블랭크에 비해 다른 특성도 나아지는 효과를 보였다. 이 시험에서 사용된 페놀 수지의 특성을 참고하여 타이어 컴파운드를 배합할 때 개질된 테르펜 페놀 수지를 선택하면 웨트 트랙션, 구름저항 등의 특성을 효과적으로 개선한 컴파운드를 만들 수 있다.