• The International Journal of Costume Culture
• /
• v.7 no.2
• /
• pp.103-111
• /
• 2004

The shrinkproof-finished wool fibers treated with resin coating and chlorination methods were used to find out an optimal shrinkproof finishing method keeping the quality properties of wool fabric to manufacturers. Shrinkage during repeated washing, electrostatic propensity, thermal resistance and pilling propensity of shrinkproof-finished wool knits, and analysis of finishing methods were measured. Upon the results from the surface examination of shrinkproof-finished wool fibers, the patterns of scale layer and degree of scale removal were subject to change according to the finishing processes. The shrink resistance was significantly enhanced on repeated washing of shrinkproof-finished knits, especially, chlorinated wool. Addition of strong physical force and alkali detergent applied in this washing experiment brought about superior effects with the low shrinkage rate although it was very severe washing conditions for wool fabrics. The results from the washing experiment implies that shrinkproof-finished knitted fabrics can be machine washed at individual households with other ordinary laundry. There was some changes and variation found in thermal resistance, electrostatic propensity, and pilling, however, it seems to be minor within standard limits. Therefore, shrinkproof-finished knitted fabrics did not bring serious changes to other physical properties comparing with original wool, which helps consumers handle wool knitted clothes more conveniently.

• Polymer(Korea)
• /
• v.27 no.3
• /
• pp.169-175
• /
• 2003

Pyrophosphoric lactone modified polyester (PATT) containing two phosphorous functional groups in one unit structure was synthesized to prepare a non-toxic reactive flame-retardant coatings. Then the PATT was cured at room temperature with isocyanate, toluene diisocyanate-isocyanurate , to get a two-component polyurethane flame-retardant coatings (PIPUC). Comparing physical properties of the films of PIPUC with those of film of non-flame-retardant coatings, there was no deterioration observed in physical properties by the introduction of a flame-retarding component into the resin. We found that the char lengths measured by 45$^{\circ}$ Meckel burner method were 3.1∼4.4 cm and LOI values recorded 27∼30%. These results indicate that the coating prepared in this study is a good flame-retardant. The surface structure of coatings investigated with SEM does not show any defects and phase separation.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.27 no.1
• /
• pp.49-58
• /
• 2009

Computer to plate technology(CTP) have become fully commercial. The current wide range of computer to plate system and plate makes many potential customers insecure. This process which began around 1995 has now been successfully completed, so that a wide variety of high performance systems is available. The computer to plate method of producing printing plates eliminates films from the production process, thus reducing costs and shortening production times. To discover the optimization formulation of sensitized materials we were changed formulation of resin and violet solution in thermal sensitizers. Also we were analyzed the CTP plate's surface and the result of coating and development at each sample. we were analyzed the effects of development condition as temperature and speed, the plate wear of printing test in C, M, Y, Bk ink. This paper aims to find out suitable ways that we can develop a domestic CTP plate.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.1
• /
• pp.81-85
• /
• 2011

Recently, the electronic parts are to be thinner plate, smaller size, light weight material and CPU, HDD and DRAM in all the parts have been produced on the basis of the high speed and greater capacity. Also, conventional goods have replaced a LED (Light-Emitting Diode) in lighting products so; such industry devices need to have cooling. To maximize all the performance on the heat-radiated products, the area of heat-radiated parts is required to be cooled for keeping the life time extension and performance of product up. Existing cooling systems are using radiant heat plate of aluminum, brass by extrusion molding, heat pipe or hydro-cooling system for cooling. There is a limitation for bringing the light weight of product, cost reduction, molding of the cooling system. So it is proposed that an alternative way was made for bringing to the cooling system. EP (Engineering Plastic) of low-cost ABS (Acrylonitrile butadiene styrene Resin) and PC (Polycarbonate) was coated with brass and the coating made the radiated heat go up. The performance of radiant heat plate is the similar to the existing part. We have studied experimentally on the radiated heat plate for the light-weight, molding improvement and low-cost. From now on, we are going to develop the way to replace the exiting plate with exterior surface of product as a cooling system.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.31 no.3 s.258
• /
• pp.295-303
• /
• 2007

Degradation behaviors of filament-winded composites have been evaluated under the accelerated environmental test of high temperature, water immersion and thermal impact conditions. Two kinds of laminated composites coated by an urethane resin have been used: carbon-fiber reinforced epoxy(T700/Epon-826, CFRP) and glass-fiber reinforced phenolic (E-glass/phenolic, GFRP). For tensile strength of $0^{\circ}$ composites, CFRP showed little degradation while GFRP did high reduction by 25% under the influence of high temperature and water However for water-immersed $90^{\circ}$ composites tensile strength of both CFRP and GFRP showed high reduction. Bending strength and modulus of $90^{\circ}$ composites were largely reduced in water-immersion as well as high temperature environment. Urethane coating on the composite surface improved the bending properties by 20%, however hardly showed such improvement for water-immersed $90^{\circ}$ composites. In case of shear strength and modulus, both CFRP and GFRP showed high reduction by water-Immersion test but did a slight increase by high temperature and thermal impact conditions.

• Journal of Korean Association for Spatial Structures
• /
• v.2 no.2 s.4
• /
• pp.11-15
• /
• 2002

Formerly, it was called a tent and now, it is called membrane structure. If saying a tent, it imagines the tent of Bedouin, Mongolia and North American Indian. It became clear from the excavated wall painting that have been covered with the retractable roof of the canvas on the auditorium at the amphitheater in Pompeii and became a topic. These tents were made of the animal skins or fabric woven with the flax plants, and these tents are still used. However, if saying membrane material at present, it says the one to have applied a coating resin to the textile. Because the base fabric of membrane material is a woven fabric, the relation between the stress and the strain is different to the direction of the weaving thread. Moreover, the tensile force must always occur in the membrane surface. From these reasons, because the membrane structure corresponds to the particular building material and the construction method about the Building Standard Law, it must be examined specially that the membrane structural building have the same or any more safety as the provisions which was set to the Building Standard Law. Therefore, the technical standards about the membrane structural building became indispensable. In the paper, the kinds of the membrane materials, which are used for the membrane structural buildings, and technical standards process of the creating for the membrane structure buildings are introduced. Lastly, some of the soccer stadiums for 2002 FIFA World Cup KOREA/JAPAN which be covered with the roof of the membrane structures are presented.

• Textile Coloration and Finishing
• /
• v.29 no.3
• /
• pp.148-154
• /
• 2017

Many researches have been made on the processing technology of Poly(ethylene terephthalate) (PET), which is widely used for clothing and non-clothing applications. In this study, we coated PET filaments with m-aramid resin to improve heat resistance and antimicrobial properties. In order to enhance adhesion between PET and m-aramid polymer, the adhesive polymer was coated on the PET filaments using a winding speed of 100m/min and then treated with m-aramid. Scanning electron microscopy was used to analyze the surface of the adhesive polymer and m-aramid treated PET filament. The change of initial degradation temperature according to treatment was confirmed by thermogravimetric analysis. Antimicrobial activity analysis using bacterial reduction method showed that PET filament treated with adhesive polymer and m-aramid had an increased antibacterial effect compared to untreated PET filament.

• The korean journal of orthodontics
• /
• v.43 no.3
• /
• pp.127-133
• /
• 2013

Objective: We aimed to investigate the effects of silanation time on the shear bond strength (SBS) of metal brackets on gold alloy in a silicoating procedure and compare the SBS of metal brackets on gold alloy and enamel. Methods: Type III gold alloy plates were sandblasted with 30-${\mu}m$ silicon dioxide. Excess particles were removed with gentle air after silica coating, and silane was applied. Maxillary central-incisor metal brackets were bonded to each conditioned alloy surface with a light curing resin adhesive for 1 s, 30 s, 60 s, or 120 s after applying silane. The brackets were also bonded to 36 upper central incisors with the same adhesive. All samples were cured for 40 s with a light emitting diode curing light. The SBS was tested after 1 h and after 24 h. The adhesive remnant index (ARI) of the samples was also compared. Results: The 60-s and 120-s silanation time groups showed a higher SBS than the other groups (p < 0.05). Samples tested after 24 h showed a significantly higher SBS than did the samples tested after 1 h (p < 0.05). The 1-s group showed higher ARI scores. The one-way analysis of variance and Student-Newman-Keuls test showed that the SBS values of the 60-s and 120-s silanation time groups were not significantly different from the SBS values of enamel. Conclusions: Adequate silanation time is required to produce sufficient bond strength during silicoating.

• Journal of the Korean institute of surface engineering
• /
• v.49 no.2
• /
• pp.218-224
• /
• 2016

Thermal radiation pastes were prepared by dispersing carbon materials as fillers with a content of 1 weight percent in an acrylic resin. The kind of fillers was as follows; $25{\mu}m$ graphite, $45{\mu}m$ graphite, $15{\mu}m$ carbon nanotube(CNT), a 1:1 mixture of $25{\mu}m$ graphite and $15{\mu}m$ CNT, and a 1:1 mixture of $45{\mu}m$ graphite and $15{\mu}m$ CNT. Thermal emissivity was measured as 0.890 for the samples with graphite only, 0.893 for that with CNT only, and 0.892 for those containing both. After coating prepared pastes on a side of 0.4 mm thick aluminium plate and placing the plate over an opening of a box maintained at $92^{\circ}C$ with the coated side out, the temperatures on the uncoated side of the plates were measured. The samples containing graphite and CNT showed the lowest temperatures. The paste with mixed fillers was coated on the back side of the PCB of an LED module and thermal analysis was carried out using Thermal Transient Tester (T3ster) in a still air box. The thermal resistance of the module with coated PCB was measured as 14.34 K/W whereas that with uncoated PCB was 15.02 K/W. The structure function analysis of T3ster data revealed that the difference between junction and ambient temperatures was $13.8^{\circ}C$ for the coated case and $18.0^{\circ}C$ for the uncoated. From the infrared images of heated LED modules, the hottest-spot temperature of the module with coated PCB was lower than that of the uncoated one for a given period of LED operation.

• Journal of the Korean Applied Science and Technology
• /
• v.35 no.3
• /
• pp.857-864
• /
• 2018

Demand for developing artificial green pearl that meets the needs of modern people has been increasing. In this paper, eco-friendly inorganic pearlescent pigment was used instead of organic pigment and urethane resin was substituted for nitrocellulose which has been used as main materials in previous preparation method, increasing gloss from 73.4% to 86.7%. Urethane was coated on substrate before finishing with CVD, resulting high gloss of 96%. Colorimeteric analysis shows that a* and b* of CIE value was changed from +37.7 and +24.5 to +31.9 and +14.2 respectively because of CVD finishing, obtaining colorful, high gloss and durable artificial pearl. Quality and toxicity of samples was established by chemical resistance, glossiness, colorimeter, surface roughness, wear resistance, content of heavy-metal, and salt water test.