• Journal of the Korean Wood Science and Technology
• /
• v.51 no.1
• /
• pp.38-48
• /
• 2023

Two important steps in utilizing technical kraft lignin (KL) from black liquor to synthesize lignin-phenol-formaldehyde (LPF) resin are its extraction via precipitation and fractionation. However, the effects of precipitation pH and acetone fractionation on the characteristics of hardwood KL have not been studied for LPF resins. Therefore, this paper reports the effects of the precipitation pH of black liquor and acetone fractionation on the characteristics of KL from mixed hardwood species for LPF resins. The precipitation was conducted at various pH levels from 3 to 9 of black liquor to obtain crude KL (C-KL), which was used in acetone fractionation to produce acetone-soluble KL (AS-KL) and acetone-insoluble KL (AI-KL). Precipitation at pH 3 and 9 produced the highest and lowest yields of C-KL, respectively. As expected, the C-KL infrared spectra were similar regardless of the precipitation pH levels. As the pH increased, the molecular weight of C-KL increased. However, the molecular weight of AS-KL and AI-KL after acetone fractionation increased to a maximum of 4,170 and 47,190 g/mol at pH 7, then decreased to 3,210 and 19,970 g/mol at pH 9, respectively. The smallest molecular weights of AS-KL and AI-KL were 3,210 and 15,480 g/mol and were found at pH 9 and 3, respectively. These results suggest that both AS-KL at pH 9 and AI-KL at pH 3 have good potential as starting lignins for synthesizing LPF resins that require cross-linking for polymerization.

• Journal of the Korean Society of Safety
• /
• v.27 no.6
• /
• pp.78-83
• /
• 2012

In this study, some experimental results of the peroxide-degradation process of polypropylene(PP) in a co-rotating twin-screw extruder to produce controlled rheology polypropylene(CRPP) are presented. The peroxide was dicumyl peroxide(DCP) and the concentration of DCP was in the range 0-0.3 wt%. It was found that the rheological properties of PP change significantly during reactive extrusion. Melt flow index(MFI) increased with DCP concentration. Intrinsic viscosity decreases with increasing DCP concentration. From dynamic rheological data, number average molecular weight(Mn), weight average molecular weight(Mn) and molecular weight distribution(MWD) were calculated. Results indicated that Mw decreases and MWD becomes narrower with increasing peroxide concentration. Especially, particle size distribution of CRPP decreases with increasing DCP concentration by chemical powdering process, and anti-slip floor paint, CRPP(DCP 0.2 wt%) powder by 10phr was friction coefficient 2.15 ${\mu}$, abrasion resistance 511.18%.

• Polymer(Korea)
• /
• v.39 no.1
• /
• pp.122-129
• /
• 2015

Recently, the development of a new class of anti-fouling paint resin which has excellent anti-fouling performance and no persistence in the marine ecology is necessary. In this study, we first polymerized polyurethanes (PUs) as the other type of matrix which have carboxylic acid groups by using poly(ethylene glycol) (PEG), 4,4'-diphenylmethane diisocyanate (MDI), and 2,2'-bis(hydroxyl methyl)-propionic acid (DMPA). And next, we synthesized final resins having quaternary ammonium salts on pendant acid groups of PUs. After synthesis, the physical self-polishing property of resin by the measurement of reduced thickness in sea water was tested. The mechanical property of antifouling paint resin was good when the molecular weight of PEG was 600 or less. It was confirmed that the adhesion of PU resin was deteriorated when the content of quaternary ammonium salt was incorporated over specific value.

• Composites Research
• /
• v.31 no.6
• /
• pp.293-298
• /
• 2018

In this paper, we have studied the physical properties of braided composites for use as aircraft stringers. Process variables such as drum winder speed, braid velocity, and mandrel diameter for $30^{\circ}$, $45^{\circ}$ and $60^{\circ}$ braid preforms were quantified and different epoxy resin types were applied to the braided preform using TGDDM, YD-128. Physical properties such as tensile strength and flexural strength of braided composites were investigated. Thermal properties and decomposition temperature of epoxy resin were investigated by TGA analysis. As a result, the lower the angle of the braid composites, the higher the tensile strength and the Flexural strength. The physical properties of braided composites fabricated using TGDDM epoxy resin were superior to the physical properties of braided composites fabricated using YD-128 epoxy resin. This is because the molecular weight of TGDDM epoxy resin was higher than that of YD-128 epoxy resin.

• Journal of Applied Biological Chemistry
• /
• v.51 no.3
• /
• pp.95-101
• /
• 2008

The gene encoding a putative esterase of Xanthomonas oryzae pv. oryzae was cloned using PCR technique. The gene was expressed with His6 tag in E. coli. One-step purification of the recombinant esterase with Ni-NTA resin resulted in one band by SDS-PAGE analysis. The purified enzyme showed a molecular weight of 30 kDa, as expected, therefore the enzyme was a mononer. The enzyme was the most active toward p-nitrophenyl (p-NP) acetate and p-NP-butyrate to a lesser extent. However, the enzyme could not hydrolyze p-NP-myristate, palmitate, and stearate. Therefore, the enzyme is considered as an esterase, very different from lipase. The purified esterase had optimal pH at around 8.0 and was stable in a broad range of pH values. The optimal temperature ranged from 30 to $40^{\circ}C$, and the residual activity observed after heat treatment at $55^{\circ}C$ for 20 min was 72 % of the initial activity. The activity was inhibited by the presence of copper and cobalt ions.

• Journal of the Korean Institute of Gas
• /
• v.2 no.3
• /
• pp.1-11
• /
• 1998

To increase peel strength, low temperature properties and flowability of pressure sensitive adhesives(PSA) used in a heat shrinkable sheet, these properties were evaluated by changing each components in type and content. In this study, Isobutylene-co-Isoprene Rubber (IIR) which has good wetherability was selected as a base polymer. Instead of rosin ester, petroleum resin was selected as a tackifier because of superior peel strength. By decreasing petroleum resin contents, flowability of PSA was decreased. High molecular weight of polybutene was better than low molecular weight for the peel strength of PSA. Large particle size of carbon black showed better properties than small one in peel strength and brittleness temperature. By adding calcium carbonate, the cost of compound was able to be reduced. But it must be used with carbon black.

• Korean Chemical Engineering Research
• /
• v.47 no.6
• /
• pp.669-675
• /
• 2009

A study has been made on the preparation of liquid resin of non-solvent and non-discoloration type for replacement of the soft PVC at room temperature. A new synthetic process was developed by structure-control design of polyurethane synthesis using pre-polymer and polyols as curing agent. The optimum recipe was made according to macro-glycols, molecular weight and reaction conditions, and the final products indicated that the mechanical properties such as tensile strength, tear strength and flexibility was very excellent than PVC products. Also, viscosity, hardness and color operations of the final products can be controlled by this system. And yellowing property by UV and NOx gas was improved from the various additive experiment.

• Applied Chemistry for Engineering
• /
• v.5 no.6
• /
• pp.1030-1035
• /
• 1994

Curing behavior and glass transition temperatures of epoxy resins into which reactive diluents were added to control processability were investigated. Heat of cure generated of the epoxy resin was reduced with butyl glycidyl ether(BGE) and phenyl glycidyl ether(PGE) contents. $T_g$ of the resin was decreased with the amount of reactive diluents and it was attributed to increased molecular weight between crosslink points. Cure kinetics of the resins was studied employing autocatalytic reaction model and found that reaction constants decreased as the contents of reactive diluent was increased.

• Journal of Applied Biological Chemistry
• /
• v.44 no.4
• /
• pp.190-193
• /
• 2001

Genipin, aglycone of geniposide isolated from fruits of Gardenia jasminoides, was transformed into blue pigments through reaction with glycine and methylamine. The blue pigments formed from glycine-reacted genipin were passed through Bio-Gel P-2 resin yielding fractions GG1 and GG2, and those from methylamine-reacted genipin were separated into fractions GM1-GM4. The first eluted higher molecular-weight fractions, GG1 and GM1, had higher tinctorial strength than the later eluted lower molecular-weight fractions, GG2 and GM2-GM4, respectively. $^1H-NMR$ spectra of GG1 and GM1 showed very broad peaks indicating that structures of the pigments were highly polymeric. $^1H-NMR$ spectra of GG2, GM3, and GM4 showed several sharp peaks at aliphatic and aromatic regions with accompanying broad peaks, although the spectrum of GM2 was rather simple. Determination of the structural and physical nature of the isolated pigments is in progress.

• Journal of the Korean Applied Science and Technology
• /
• v.23 no.4
• /
• pp.319-327
• /
• 2006

In order to prepare high-solid coatings, first acrylic resins (HSAs) which contain 80% solid were synthesized, and then the prepared resins were cured with isocyanate at room temperature. In the synthesis of HSAs, viscosity, number average molecular weight $(M_n)$ and conversion were $1372{\sim}2700$ cps, $1520{\sim}1650$ and $83{\sim}87%$, respectively. Among the four kinds of initiators used, tert-amylperoxy-2-ethyl hexanoate was the most proper one in the synthesis of HSAs. With increasing $T_g$ values, viscosity increased rapidly and molecular weight increased slowly. As a result of the examination of coated films, it was found that $60^{\circ}$ specular gloss, impact resistance, heat resistance and cross-hatch adhesion were good, and pencil hardness, drying time and pot life were poor.