• 제목/요약/키워드: Residual Deformation

검색결과 609건 처리시간 0.026초

WC위 TiAlN 코팅층에 미치는 Sand Blasting 처리의 영향 (Effects of Sand Blasting on TiAlN Coating on WC Hard Metal Alloy Tip)

  • 이한영
    • Tribology and Lubricants
    • /
    • 제37권2호
    • /
    • pp.54-61
    • /
    • 2021
  • The effect of the sand blasting before TiAlN coating in the manufacture of WC hard metal alloy tips have been studied. For four different tips, according to the status of processing of the sand blasting and the coating, residual stress measurement by X-ray diffraction and several tests for mechanical properties have been conducted. The results suggest that there was no difference in static mechanical properties, such as hardness, surface roughness and elastic modulus, between two coatings. Furthermore, compressive residual stress was generated equally on their surfaces. Additionally, the compressive residual stress in substrate WC was found to increase greatly when subjected to sand blasting treatment. However, the compressive residual stress decrease after coating regardless of sand blasting treatment. Nevertheless, it is confirmed that the compressive residual stress generated in the coating after sand blasting is less than that in the non-sandblasting coating. This was attributed to the plastic deformation occurring in the WC substrate during coating after sand blasting. In contrast to the scratch test results, sand blasting was assumed to have a negative effect on the adhesion between the coating and substrate. This is because there is a high possibility of microcracks due to plastic deformation in the WC substrate under the coating after sand blasting.

사출 성형품의 금형내 잔류음력과 이형후 냉각에 의한 후변형 해석 (Deformation Analysis of Injection Molded Articles due to In-mold Residual Stress and Subsequent Cooling after Ejection)

  • 양상식;권태헌
    • 대한기계학회논문집A
    • /
    • 제26권2호
    • /
    • pp.340-348
    • /
    • 2002
  • Deformation analysis of injection molded articles whose geometry is considered as the assembly of thin flat plates has been conducted. For the in-mold analysis, thermo-viscoelastic stress calculation of thermo-rheologically simple amorphous polymer and in-mold deformation calculation considering the in-plane mold constraint have been done. Free volume theory has been used to represent the non-equilibrium density state during the fast cooling. At ejection, instantaneous deformation takes place due to the redistribution of in-mold residual stress. During out-of-mold cooling after ejection, thermoelastic model based on the effective temperature has been adopted for the calculation of out-of-mold deformation. In this study, emphasis is also made on the treatment with regard to lateral constraint types during molding process. Two typical mold geometries are used to test the numerical simulation modeling developed in this study.

3-D 점탄성 모델을 이용한 복합재 성형후 잔류변형해석 및 몰드 효과 연구 (Residual Deformation Analysis of Composite by 3-D Viscoelastic Model Considering Mold Effect)

  • 이홍준;김위대
    • Composites Research
    • /
    • 제34권6호
    • /
    • pp.426-433
    • /
    • 2021
  • 탄소 섬유 강화 복합재료는 오토클레이브 공정 시 발생하는 잔류응력이 발생하고, 스프링 인, 뒤틀림과 같은 열변형으로 인해 치수 결함이 발생한다. 열변형의 주요원인은 제품의 형상, 수지의 화학 수축과 열팽창, 몰드의 재질과 표면 상태에 따른 몰드 효과 등 다양한 요인에 의해 발생한다. 본 연구는 열변형을 예측하기 위해 점탄성 모델 해석 기법을 평판 모델에 적용하여 열변형의 주요 원인인 수지의 화학 수축과 열팽창의 영향을 분석했고, 몰드 유무에 따른 3-D 점탄성 모델의 해석 기법을 검증했다. 검증된 3-D 점탄성 모델의 해석 기법을 이용하여 L-형상의 몰드 효과를 분석한 결과, 동일한 재질의 몰드를 사용했더라도 표면 상태에 따라 잔류 변형이 다르게 나타났다.

광폭인장시험을 통한 지오그리드의 시간의존적 변형 거동 고찰 (Time-dependent Deformation Charateristics of Geogrid Using Wide Width Tensile Test)

  • 유충식;전한용;김선빈
    • 한국지반공학회논문집
    • /
    • 제24권1호
    • /
    • pp.71-80
    • /
    • 2008
  • 본 논문에서는 보강토 구조물에 보강재로 적용되는 지오그리드의 시간 의존적 변형거동 특성에 대한 광폭 인장시험 결과를 제시하였다. 먼저, 다양한 보강재의 종류에 대해 인장속도에 따른 파단강도 및 강성의 변화에 대해 알아보았다. 또한 보강토 구조물이 사용연한 동안 받게될 다양한 하중 조건, 즉 지속하중 및 반복하중을 작용시킬 수 있는 장비를 특수 제작하여 지오그리드의 시간의존적 변형거동을 분석하였다. 그 결과 지속하중 및 반복하중 작용시 잔류변형은 보강재의 점성(viscous) 특성의 형태로서 쌍곡선 특성 곡선으로 잘 모사되는 것으로 분석되었으며 이러한 잔류변형은 시간의존적 점성거동의 측면에서 다루어야 하는 것으로 나타났다.

용접에 의한 자동차용 Frame의 변형과 잔류 응력 분석 (Deformation and Residual Stress of Automotive Frame by Welding)

  • 박태원;김기주;한창평;이영숙;임종한
    • 한국자동차공학회논문집
    • /
    • 제19권5호
    • /
    • pp.113-117
    • /
    • 2011
  • The frame for automotive assembly can be deformed and remained on the residual stress due to high temperature thermal attacks when in welding. The frame deformation can be made to problems when in assembly with body and the residual stress can affect the negative effect on durability performance of the automobile. In order to analyze the frame deformation, the simplified test frame which had the similar shape (form) of the real automotive frame was fabricated. The contactless optical 3D scanner was used for the shape difference measurement of the frame between before and after the welding. The FE-model of the test frame was composed and the heat transfer and thermal stress simulation were performed. The simulated results were compared with the measured results for the reference of the frame design. The deformation shape of the frame by simulation was in good agreement with that by the experimental measurement.

Pilot study for investigating the inelastic response of a new axial smart damper combined with friction devices

  • Mirzai, Nadia M.;Hu, Jong Wan
    • Steel and Composite Structures
    • /
    • 제32권3호
    • /
    • pp.373-388
    • /
    • 2019
  • This study proposes a new concept of an axial damper using the combination of shape memory alloy (SMA), friction devices, and polyurethane springs. Although there are many kinds of dampers to limit the damages, large residual deformation may happen and it causes much repairing cost for restoring the structure to the initial position. Also in some of the dampers, a special technology for assembling and fabricating is needed. One of the most important advantages of this damper is the ability to remove all the residual deformation using SMA plates and simple assembling without any special technology to fabricate. In this paper, four different dampers (in presence or omission of friction devices and polyurethane springs) are investigated. All four cases are analyzed in ABAQUS platform under cyclic loadings. In addition, the SMA plates are replaced by steel ones in four cases, and the results are compared to the SMA dampers. The results show that the axial polyurethane friction (APF) damper could decrease the residual deformation effectively. Also, the damper capacity and dissipated energy could be improved. The analysis showed that APF damper is a good recentering damper with a large amount of energy dissipation and capacity, among others.

단일 숏 충돌에서의 잔류응력 유일해를 위한 2차원 유한요소해석 모델 (A 2D FE Model for a Unique Residual Stress in Single Shot Impact)

  • 김태형;이형일
    • 대한기계학회:학술대회논문집
    • /
    • 대한기계학회 2007년도 춘계학술대회A
    • /
    • pp.183-188
    • /
    • 2007
  • In this paper, we propose a 2D-FE model in single impact with combined physical factors to obtain a unique residual stress by shot peening. Applied physical parameters include elastic-plastic deformation of shot ball, material damping coefficients, strain rate, dynamic friction coefficients. Single impact FE model consists of 2D axisymmetric elements. The FE model with combined factors showed converged and unique distributions of surface stress, maximum compressive residual stress and deformation depth. Further, in contrast to the FE models with rigid shot and elastic deformable shot, FE model with plastic deformable shot produces residual stresses very close to experimental solutions by X-ray diffraction. We therefore validated the 2D FE model with combined peeing factors and plastic deformable shot. This FE model will be a base of the 3D FE model for residual stresses by multi-impact shot peening.

  • PDF

Evaluation of Residual Stresses in 12%-Cr Steel Friction Stir Welds by the Eigenstrain Reconstruction Method

  • Jun, Tea-Sung;Korsunsky, Alexander M.
    • 한국생산제조학회지
    • /
    • 제24권1호
    • /
    • pp.15-22
    • /
    • 2015
  • In the present paper we report the results of a study into Friction Stir Welds (FSWs) made in 13 mm-thick 12%-Cr steel plates. Based on residual strains obtained by diffraction techniques, eigenstrain analysis was performed using the Eigenstrain Reconstruction Method (ERM), which is a novel methodology for the reconstruction of full-field residual strain and stress distributions within engineering components. Significant eigenstrain distributions were found at around Thermo-Mechanically Affected Zone (TMAZ) where the most severe plastic deformation was occurred. Microstructure analysis was used to elucidate this phenomenon showing that the grain structure in TMAZ was bent and not successfully recrystallised, resulting in severe deformation behaviour. The reconstructed residual strain distributions by the ERM agree well with the experimental results. It was found that the approach based on theory of eigenstrain is a powerful basis for reconstructing the full-field residual strain/stress distributions in engineering components and structures.

레벨링 공정 해석에 의한 교정 조건이 열연 고장도 강판의 잔류음력에 미치는 영향 연구 (Effect of the Leveling Conditions on Residual Stress Evolution of Hot Rolled High Strength Steels by Deformation Analysis of Leveling Process)

  • 박기철
    • 한국소성가공학회:학술대회논문집
    • /
    • 한국소성가공학회 2009년도 춘계학술대회 논문집
    • /
    • pp.326-329
    • /
    • 2009
  • In order to analyze the effect of leveling conditions on residual stress evolution of hot rolled high strength steels, a numerical algorithm was developed. It was able to implement the effect of plastic fraction (intermesh) in leveling, line tension, work roll bending, and initial residual stress and curl distribution. The effect of work roll bending on residual stress and curl were studied by using the developed program. The validity of simulated results was verified from comparison with the experimentally measured residual stress and curl in a sheet.

  • PDF

금속 적층제조 방식을 이용한 SUS316L 시편의 공정 파라미터 및 금속 분말 재사용에 따른 변형량 변화 분석 (Analysis of Variations in Deformations of Additively Manufactured SUS316L Specimen with respect to Process Parameters and Powder Reuse)

  • 김민수;김지윤;박은교;김태민;조진연;김정호
    • 한국항공우주학회지
    • /
    • 제50권4호
    • /
    • pp.223-231
    • /
    • 2022
  • 금속 적층제조 공정 중 발생할 수 있는 잔류응력은 3D 프린팅을 통한 정밀한 금속 부품 제작을 위해 적절히 통제되어야 하는 중요한 요소이다. 따라서 본 연구에서는 이러한 잔류응력에 영향을 끼치는 요인에 대하여 실험적인 방법을 이용하여 고찰하였다. 실험을 위해 적층제조 공정을 통해 시편을 제작하고 이를 절단하여 변형량 측정을 수행하였으며, 측정된 데이터를 curve fitting 등의 방법을 이용하여 적절히 보정함으로써 공정 파라미터 및 금속 분말 재사용 여부가 금속 적층제조 공정에서 발생한 잔류응력으로 인한 변형에 끼치는 영향을 정량적으로 분석할 수 있는 자료를 확보하였다. 이 결과로부터 금속 적층제조 공정에서 잔류응력으로 인한 변형의 크기에 가장 큰 영향을 끼치는 요소는 금속 분말 재사용 여부임을 확인하였다. 또한 레이저의 패턴, 적층 회전 각도와 같은 공정 파라미터도 변형 크기에 영향을 줄 수 있는 것을 확인하였다.