• 한국해양공학회지
• /
• 제25권6호
• /
• pp.49-55
• /
• 2011

In order to analyze feasibility of replacing a conventional 6-mm Ti bar with a 5-mm bar, a series of rotating bending fatigue tests were carried out on Ti-6Al-4V bars by strengthening the fatigue performance using a special technique called UNSM (Ultrasonic Nanocrystal Surface Modification). The results of S-N curves clearly showed that the performance of the 5-mm titanium specimen was similar to that of the 6-mm specimen when the UNSM treatment was applied. The 5-mm treated specimen converged with small scattering band into the linear line of the non-treated 6-mm one. Below the fatigue life of $10^5$ cycles, the UNSM treatment did not show any significant superiority in the bending stress and fatigue life. However, over the fatigue life of $10^5$ cycles, the effect of UNSM was superior for each fatigue life, and the bending stress became longer and higher than that of the untreated one. In the case of 6-mm Ti-bar with UNSM, the fatigue limit was about 592 MPa, and there was fatigue strength increase of about 30.7% at the fatigue life of $10^4$ cycles compared to the untreated 6-mm bar. Therefore, the compressive residual stress made by the UNSM in Ti-6Al-4V increased the fatigue strength by more than 30%.

• 한국세라믹학회지
• /
• 제34권3호
• /
• pp.257-264
• /
• 1997

MPB조성영역에 MnO2를 첨가한 압전체를 제조하여 분극처리후에 반복압축응력을 부여함에 따른 압전열화 현상을 조사하고 분극처리 전후의 굽힘강도의 변화 및 파괴특성을 연구하였다. MnO2를 0.25wt.% 첨가한 시편에서 가장 적은 열화현상이 일어났다. 굽힘강도는 분극처리 후 하중방향에 평행한 방향으로 분극처리한 시편이 분극처리 전보다 높은 강도를 나타내었고, 수직한 방향으로 분극처리한 시편은 낮은 값을 나타내었다. 이는 분극처리시 발생하는 전계방향으로 압축잔류응력, 직각방향으로 인장잔류응력 때문인 것으로 사료된다.

• International Journal of Safety
• /
• 제1권1호
• /
• pp.24-27
• /
• 2002

Recently the steel parts used in automobiles are required to be used under high stress more than ever before due to the need of keeping the weight down. To achieve this requirement of the high strength steel, it must be necessary to decrease inclusion contents and surface defects as like decarburization, surface roughness etc. In this study, the surface conditions are measured to know the influence on fatigue properties by two cases of two-stage shot peening and single-stage shot peening. And for this study, three kinds of spring steel (JISG408l-SUP7, SAE 9254 and DIN 50CrV4) are shaped. This study shows the outstanding improvement of fatigue properties at the case of two-stage shot peening in the rotating bending fatigue test and it results from (1) decreasing the surface roughness (2) unchanging the surface hardness (3) increasing the compressive residual stress. Moreover, results also show fatigue failures originated at the inclusion near the surface, and this inclusion type is turned out to be an alumina of high hardness.

• 동력기계공학회지
• /
• 제5권4호
• /
• pp.67-73
• /
• 2001

Recently the steel parts used at automobiles are required to be used under high stress more than ever before in need of the weight down. To achieve this requirement of a high strength steel, it must be necessary to decrease inclusion content and surface defect as like decarburization, surface roughness etc.. In this study, the surface conditions are measured to know the influence on fatigue properties by two cases of two-stage shot peening iud single-stage shot peening for two kinds of spring steel(SUP7, SAE9254). This study shows the outstanding improvement of fatigue properties at the case of two-stage shot peening in the rotary bending fatigue test and this is assumed to be from decreasing the surface roughness unchanging the surface hardness increasing the compressive residual stress. Results also show fatigue failures originated at inclusion near surface, and this inclusion type is turned out to be a alumina of high hardness.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2001년도 추계학술대회 논문집(Proceeding of the KOSME 2001 Autumn Annual Meeting)
• /
• pp.71-79
• /
• 2001

Recently the steel parts used at automobiles are required to be used under high stress more than ever before in need of the weight down. To achieve this requirement of a high strength steel, it must be necessary to decrease inclusion content and surface defect as like decarburization, surface roughness etc.. In this study, the surface conditions are measured to know the influence on fatigue properties by two cases of shot peening of two-stage shot peening and single-stage shot peening. And for this study, three kinds of spring steel(JISG4081-SUP ,SAE 9254, DIN 50CrV4, ) are made. This study shows the outstanding improvement of fatigue properties at the case of two-stage shot peening in the rotary bending fatigue test and this is assumed to be from (1) Decreasing the surface roughness (2) Unchanging the surface hardness (3) Increasing the compressive residual stress But, results also show fatigue failures originated at inclusion near surface, and this inclusion type is turned out to be a alumina of high hardness.

• 한국자동차공학회논문집
• /
• 제11권1호
• /
• pp.185-192
• /
• 2003

Recently the steel parts used at automobiles are required to be used under high stress more than ever before in need of the weight down. To achieve this requirement of a high strength steel, it must be necessary to decrease inclusion content and surface defect as like decarburization, surface roughness etc.. In this study, the surface conditions are measured to Dow the influence on fatigue properties by two cases of shot peening of two-stage shot peening and single-stage shot peening. And for this study, three kinds of spring steel (JISG4081-SUP7, SAE 9254, DON 50CrV4) are made. This study shows the outstanding improvement of fatigue properties at the case of two-stage shot peening in the rotary bending fatigue test and this is assumed to be from (1) Decreasing the surface roughness (2) Unchanging the surface hardness (3) Increasing the compressive residual stress. But, results also show fatigue failures originated at inclusion near surface, and this inclusion type is turned out to be a alumina of hish hardness.

• 한국강구조학회 논문집
• /
• 제16권2호통권69호
• /
• pp.215-224
• /
• 2004

에너지법을 이용하여 보-기둥 및 기둥의 비탄성 좌굴거동을 해석하였다. 미국에서 생산되는 I 형강에 적용되는 단순형 잔류응력 모델을 우리나라에서 생산되는 I 형강에 적용하였다. 먼저, 집중 압축 축하중과 균등 휨을 동시에 받는 I 형강에 대하여 비탄성 횡-비틀림 좌굴거동을 알아보고 보-기둥에서의 잔류응력의 영향을 해석하였다. 또한 기둥의 경우에 대하여 해석하였으며 얻어진 결과를 강구조편람에 의한 설계 시의 값과 비교하였다. 결론적으로 강구조편람에 의한 설계는 과설계가 됨을 알 수 있었다.

• Transactions on Electrical and Electronic Materials
• /
• 제6권4호
• /
• pp.149-153
• /
• 2005

In this paper, we investigated the island density-dependent stress distribution of indium-tin-oxide (ITO) film on polycarbonate substrate by external bending force. We used e-beam and RF­sputter for SiON, ITO sputtering. It was found that there are influence of island density on the substrate and decreasing crack density as goes to the minimum density. From the result that crack density was increasing at maximum island density, it is evident that more stress is imposed on same island position as island density.

• 한국강구조학회 논문집
• /
• 제16권1호통권68호
• /
• pp.155-167
• /
• 2004

각각 집중하중과 등분포하중을 받는 단순보의 비탄성 횡-비틀림 좌굴에 대하여 연구하였다. 잔류응력을 단순형과 다항식형으로 하여 line-type 유한요소법으로 해석하였다. 잔류응력의 형태는 플랜지에서는 4차 곡선으로 웨브에서는 2차 곡선으로 가정하였다. 우리나라에서 생산되는 4종류의 I형강에 대하여 비탄성 횡-비틀림 좌굴에 대하여 해석한 후 결과를 강구조편람의 내용과 비교하였다. 해석결과로부터 강구조 편람에 의한 설계는 주보에 보조보가 있는 경우나 없는 경우 모두 전반적으로 과설계임을 알 수 있었다.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1997년도 추계학술대회 논문집
• /
• pp.322-327
• /
• 1997

This paper investigates the effects of shot peening on mechanical properties of SAE 9254, which is a spring steel used for the suspension system of automobiles. Rotary Bending Fatigue test is accomplished and the results are summarized as fellows : 1. The tensile strength and the hardness do not change so much. 2. The layer of highly residual stress is obtained by multi-stage shot peening. 3. The fatigue strength seems to be improved by residual stress. 4. The fatigue strength of un-peened and multistage shot peened material are 425 MPa and 756 MPa, respectively.