• 한국철도학회논문집
• /
• 제7권1호
• /
• pp.55-59
• /
• 2004

Composite materials were used widely due to merit of light weight, low maintenance cost and easy installation. But it is the cause of enormous casualties to men and properties because of weak about the fire. Particularly, it is more serious in case of subway train installed composite materials. For this reason, experimental comparison has been done fur measuring heat release rate(H.R.R) and smoke production rate(S.P.R) of interior panels of electric motor car using cone calorimeter. A high radiative heat flux of 50kW/㎡ was used to bum out all materials and to simulate the condition of fully developed fire case in the tests. It was observed that Heat Release Rate and Smoke Production Rate curves were dependent on the kinds of the interior materials. From the heat release rate curves, the sustained ignition time, peak heat release rate and total heat release rate were deduced, These data are useful in classifying the materials by calculating two parameters describing the possibility to flashover.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2008년도 추계 학술논문 발표대회
• /
• pp.63-66
• /
• 2008

Not only mechanical properties, bonding properties, electro chemical properties, etc. but also fire safety is required in patch repair materials such as polymer modified cement mortar (PCM) which are used to deteriorated reinforced concrete structure. Unfortunately, it is very difficult to choice the appropriate repair materials because there are not enough information about fire safety properties of PCM. In this study, The combustion characters of PCM were evaluated through the heat release rate test and non-combustibility test. The pyrogenicity test uses the cone calorimeter based on the oxygen consumption method. The non-combustibility test is from the temperature change inside the furnace during the test. The effect of the types of polymer and polymer content were evaluated from the series of test. The results are like followings. 1) The higher the W/C of PCM, the lower the gross calorific value and heat generation rate in the heat release rate test. The amount of heat generation of PCM is like the order of VVA, EVA, and SBR in this study. 2) Some materials such as E45-100, E50-100, E60-100, S50-50, and S50-100 were estimated as not appropriate building materials in the non combustibility test.

• 유변학
• /
• 제8권2호
• /
• pp.129-138
• /
• 1996

접착강도는 접착제의 점탄성을 반영한 온도·속도 의존성을 나타낸다는 것이 잘 알 려져있다. 특히 유리전이온도(Tg)에서의 역학적 완화기구가 접착층의 변형을 수반하는 접착 층의 변형을 수반하는 접착강도에 크게 영향을 미치고 있다. 또한 접착계의 모드I의 변형에 너지 해방율(GIC)를 측정할때에도 접착제의 변형과 파괴가 발생하기 접착제의 점탄성이 그 값에 어떠한 영향을 미치는 지에 흥미가 깊다. 본 연구에서는 2종류의 에폭시 수지를 블랜 드한 접착제를 이용하여 일정한 측정조건에서 인장 접착강도와 GIC의 상관관계에 대하여서 도 토론하였다.

• Journal of Pharmaceutical Investigation
• /
• 제21권1호
• /
• pp.1-10
• /
• 1991

Hydrogels containing ketoprofen were prepared by adding NaOH or $Ca(OH)_2$ solution to Eudragit L, S and Eudispert hv at various concentration. And xerogels were prepared by drying hydrogels. On the other hand, organogels containing ketoprofen were prepared by mixing Eudragit L or S and propylene glycol. Effects of polymer content and base on drug release were investigated using KP V dissolution method. The release rate of ketoprofen from Eudragit L & S hydrogel decreased with increasing in polymer content. And the drug release rate from cal. hydroxide based gels were more decreased than that from sod. hydroxide based gels. At pH 7.2 dissolution medium, e release of ketoprofen from Edispert hv hydrogel followed apparent zero order kinetics. The release of ketoprofen from xerogel involved in simultaneous absorption of water and desorption of ketoprofen via a pH-dependant swelling controlled mechanism. The release of ketoprofen from Eudragit S organogels followed apparent zero order kinetics, providing strong evidence for a surface erosion mechanism.

• 대한의용생체공학회:의공학회지
• /
• 제41권1호
• /
• pp.62-66
• /
• 2020

Controlled drug release is important for effective treatment of cancer. Poly(DL-lactide-co-glycolide) acid (PLGA) is a Food and Drug Administration (FDA) approved polymer and have been extensively studied as drug delivery carriers with biodegradable and biocompatible properties. However, PLGA drug delivery carriers are limited due to the initial burst release of drug. Certain drugs require an early rapid release, but in many cases the initial rapid release can be inefficient, reducing therapeutic effects and also increasing side effects. Therefore, sustained release is important for effective treatment. Poly Lactic Acid stereo complex (PLA SC) is resistant to hydrolysis and has high stability in aqueous solutions. Therefore, in this work, PLGA based discoidal polymeric particles are modified by Poly Lactic Acid stereocomplex (PLAsc DPPs). PLAsc DPPs are 3 ㎛ in diameter, also showing a relatively sustained release profile. Fluorescein 5(6)-isothiocyanate (FITC) released from PLAsc DPPs was continuously observed until 38 days, which showed the initial release of FITC from PLAsc DPPs was about 3.9-fold reduced as compared to PLGA based DPPs at 1 hour.

• 한국화재소방학회논문지
• /
• 제23권4호
• /
• pp.73-78
• /
• 2009

본 연구는 콘칼로리미터를 사용하여 한국 리기다 소나무, 밤나무, 느티나무의 연소성질을 조사하였다. 이들 종에 대한 열방출율과 연기 발생량을 측정하였다. 숯생성으로 인한 연소성 억제 증대에 대하여, 느티나무는 리기다 소나무, 밤나무에 비하여 좋은 성질을 보였다. 밤나무는 리기다 소나무, 느티나무에 비하여 높은 CO수율과 높은 $CO/CO_2$ 수율을 나타내었다.

• 폴리머
• /
• 제27권6호
• /
• pp.536-541
• /
• 2003

불포화 폴리(3-히드록시알칸오에이트) (UPHA)를 생합성하고 이 고분자 매트릭스 내에서의 약물방출 경향을 조사하였다. UPHA의 생합성에 사용된 균주는 Pseudomonas oleovorans (ATCC 29347)이고 탄소원은 10-undecenoic acid를 사용하였으며 산-염기조절방법 배취형태 발효법을 이용하여 미생물 배양을 행하였다. 생합성된 UPHA는 $^1$H- 및 $^{13}$C-NMR, FT-IR, GPC 및 DSC 등을 사용하여 물리 및 화학적 분석을 행하였다. 약물방출 실험은 확산셀을 이용하여 모델약물인 케토프로펜의 방출량을 HPLC를 이용하여 측정하였고 UPHA의 가교도, 패취두께, 경피투과 향상제 등의 영향에 대하여 조사하였다. UPHA의 가교도의 증가에 따라 약물방출 속도가 늦어지고 약물방출 속도가 일정해지는 경향을 나타내었다. 경피투과용 패취의 두께가 두꺼워질수록 약물방출 지속시간이 길어지고 경피투과 향상제인 프로필렌 글리콜의 함량 증가에 따라 방출 속도가 향상되는 경향을 나타내었다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.360.1-360.1
• /
• 2016

Hydroxyapatite (Ca10(PO4)6(OH)2, HAP) particles have attracted a great deal of attention in biomedical fields due to their good biocompatibility, bioactivity and fairly broad applications as drug delivery, dental implant, bone cement, and etc. Thus, many researchers have made an effort to add new functionalities such as luminescence, drug delivery, and bone regeneration properties up to HAP powders by controlling their nanostructure as well as composition. In this research, the mesoporous strontium substituted HAP (Sr-HAP) microspheres were synthesized using a hydrothermal method. In this synthesis, aspartic acid monomers were utilized to form microsphere by controlling surface energy of HAP particles and Sr ions were substituted into Ca ion sites, which induced luminescence property in HAP powders. Moreover, the change in the amount of Sr substitution was found to influence the particle size, morphology, and concurrently surface area, which led to changing drug loading as well as drug release property. The amount of Sr influences the morphology, luminescent properties, particle size, surface area cell viability and drug loading property, which are investigated by SEM, TEM, XRD, FTIR, BET, XPS and in vitro test such as MTT assay and drug release test. In particular, the multifunctional Sr-HAP with molar ratios of 0.25 (Sr/(Ca+Sr)) possessed the strongest luminescent property as well as the superior drug loading and sustained release properties that were correspondent with large surface area and pore size. Our study indicates that the fabricated multifunctional Sr-HAP microspheres are quite useful for bone regeneration and drug delivery.

• 약학회지
• /
• 제41권1호
• /
• pp.48-59
• /
• 1997

Sustained release matrix tablets, pellets, and coated pellets for the delivery of sulindac were prepared using cellulose derivatives at various ratios, and evaluated for the dis solution pattern. The release of sulindac, from matrix tablets prepared with low viscosity HPMC was relatively fast, and especially the tablets made of Metolose SM released all of sulindac within 1 hr. The release of drug from tablets made of other HPMC derivatives were retarded in the order of the following: Pharmacoat 645>Pharmacoat 606>Pharrnacoat 606+HPC-L>HPC-L. The most sustained release pattern was observed with the preparation of high viscous polymer. Metolose 90 SH. While release of sulindac, from matrix type pellet containing 10mg/cap of Metolose 90 SH or 60 SH was completed within 1 hr, a prolonged release formulation (30% in 1 hr) was obtained by the inclusion of EC. Pellets coated with HPMC showed a fast release pattern (${\geq}$ 80% within 2 hrs), whereas pellets coated with HPMC and EC (molar ratio 1 : 1) showed a sustained release pattern (${\geq}$ 80% in 12 hrs), vath the release from EC pellets being the most sustained. Fast (naked) and slow release pellets coated with EC, Metolose 60SH 50cps and propylene glycol. and enteric pellets coated with HPMCP 55 and Myvacet$^{\circledR}$ were prepared, and combined at various ratios for the assessment of dissolution pattern. The result indicates the possibility that the development of 24 hr sustained release delivery systems containing sulindac for oral administration could be achieved by means of combining sustained and fast release pellets at a proper portion.

• Journal of Advanced Marine Engineering and Technology
• /
• 제28권7호
• /
• pp.1063-1071
• /
• 2004

Accurate heat release analysis of cylinder pressure data is important for evaluating performance in the development of diesel engine However, traditional single zone first law heat release model(SZM) has significant limitations due to the simplified assumption of uniform charge and neglecting local temperature inside cylinder during combustion process. In this study. heat release rate based on single zone heat release model has been evaluated by comparison with computational analysis results using Fire code which is based on multi-dimensional model(MDM). To overcome limitations due to simplicity of single zone assumption. especially the influence of specific heat ratio on gross heat release has been esteemed and newly suggested were the equation $\gamma$= $\gamma$(${T/T}_{max}$) which describes the variations of gases thermodynamic properties with mean temperature and maximum mean temperature inside cylinder Single zone heat release model applied with this equation is shown to give very good results over whole range of operating conditions when compared with computational analysis results based on multi-dimensional model.