• Biomaterials and Biomechanics in Bioengineering
• /
• 제1권1호
• /
• pp.13-25
• /
• 2014

In the current study, a drug-eluting stent coated with biodegradable polymers and sirolimus was developed by using an ultrasonic nanocoater and characterized in aspects of surface smoothness and coating thickness. In addition, in vitro release profiles of sirolimus by changing top coating layer with different biodegradable polymers were investigated. Smooth surfaces with variable thickness could be fabricated by optimizing polymer concentration, flow rate, nozzle-tip distance, gas pressure, various solvents and ultrasonic power. Smooth surface could be generated by using volatile solvents (acetone, chloroform, and methylene chloride) or post-treating with solvent vapor. Coating thickness could be controlled by varying injection volume or polymer concentration, and higher concentration could reduce the coating time while obtaining the same thickness. The thickness measurement was the most effectively performed by a conventional cutting method among three different methods that were investigated in this study. Release profiles of sirolimus were effectively controlled by changing polymers for top layer. PLGA made the release rate 3 times faster than PDLLA and PLLA and all top layers prevented burst release at the initial phase of profiles. Our results will provide useful and informative knowledge for developing drug-eluting stents, especially coated with biodegradable polymers.

• Journal of Pharmaceutical Investigation
• /
• 제35권6호
• /
• pp.445-451
• /
• 2005

As a selective ${\alpha}_{1A}-adrenoreceptor$ antagonist, tamsulosin has been used clinically for urinary obstructed patients with benign prostatic hyperplasia. The single and multi-layered pellets containing tamsulosin hydrochloride were prepared in an effort to control the drug release, avoiding dose-dependent side effects of tamsulosin hydrochloride upon oral administration. The drug release from multi-layered pellets was substantially controlled, compared with single layered pellets. The drug release from coated pellets with single or multi layer was affected by the nature of coating agent, the percentage of coating level and the presence of hydrophilic material in coating layer. In conclusion, the controlled release oral delivery system using multi-layered pellet is very useful for tamsulosin hydrochloride, resulting in improvement of patient compliance and therapeutic drug levels for a longer period of time.

• 대한기계학회논문집B
• /
• 제20권2호
• /
• pp.605-615
• /
• 1996

Laminar flows in which mixing and chemical reactions take place between parallel streams of reactive species are studied numerically. The governing equations for laminar flows are from two-dimensional compressible boundary-layer equations. The chemistry is a finite rate single step irreversible reaction with Arrhenius kinetics. Ignition, premixed flame, and diffusion flame regimes are found to exist in the laminar reacting mixing layer at high activation energy. At high Mach numbers, ignition occurs earlier due to the higher temperatures in the unburnt gas. In diffusion regimes, property variations affect the laminar profiles considerably and need to be included when there are large temperature differences. The maximum temperature of a laminar reacting mixing layer is almost linear with the adiabatic flame temperature at low heat release, but only weakly at high heat release.

• Structural Engineering and Mechanics
• /
• 제23권2호
• /
• pp.163-175
• /
• 2006

In this paper, the dynamic response of a piezoelectric layer with a penny-shaped crack is investigated. The piezoelectric layer is subjected to an axisymmetrical action of both mechanical and electrical impacts. Two kinds of crack surface conditions, i.e., electrically impermeable and electrically permeable, are adopted. Based upon integral transform technique, the crack boundary value problem is reduced to a system of Fredholm integral equations in the Laplace transform domain. By making use of numerical Laplace inversion the time-dependent dynamic stress and electric displacement intensity factors are obtained, and the dynamic energy release rate is further derived. Numerical results are plotted to show the effects of both the piezoelectric layer thickness and the electrical impact loadings on the dynamic fracture behaviors of the crack tips.

• Journal of the Korean Physical Society
• /
• 제73권9호
• /
• pp.1279-1282
• /
• 2018

This paper reports the deposition of a metal line using a multilayer stack and laser-induced forward transfer (LIFT) using a low cost continuous wave blue laser with a wavelength of 450 nm. The donor structure was composed of a light-to-heat (LTH) layer, a release layer, and a transfer layer in series. Amorphous silicon as the LTH layer absorbs photon energy and converts it to heat. A release layer was melted so that a silver transfer layer would be transferred to the receiver substrate. The transferred silver layer showed reasonable physical and electrical characteristics. A low cost fine linewidth metal layer could be achieved using this modified LIFT technique and blue laser.

• 폴리머
• /
• 제28권4호
• /
• pp.335-343
• /
• 2004

카뮤스틴 (1,3-bis(2-chloroethy1-nitrosourea, BICNU)은 뇌종양 치료를 위하여 임상적으로 사용되는 약물로 짧은 생물학적 반감기를 가지고 있어 장기방출에 적합하지 않다. 하지만, poly(D,L-lactide-co-glycolide) (PLGA)는 벌크 분해 특성으로 인해 약물의 장기방출에 유용하며, PLGA의 유도체인 글리콜라이드 단량체는 독성이 없고 PLGA와 유사한 생분해성을 가지고 있어 BICNU의 방출조절에 이용된다. 이 실험에서 BICNU를 함유한 PLGA 웨이퍼는 일반적인 직접압축법에 의해 제조한 후 BICNU의 방출거동과 웨이펴의 분해속도를 전자주사현미경, 핵자기공명장치 그리고 젤투과크로마토그래피를 통해 관찰하였다. 또한, 글리콜라이드 단량체의 함량변화에 따른 다중층 웨이퍼를 제조하여 단일층 웨이퍼와의 방출거동을 비교하였다. 이러한 결과들로부터 BICNU를 함유한 PLGA 웨이퍼의 약물방출은 BICNU와 글리콜라이드 단량체의 함량이 증가할수록 증가하였고, 다중층 웨이퍼에서 외부층의 글리콜라이드 단량체와 BICNU가 약물방출 거동과 분해속도에 영향을 미친다는 것을 확인하였다.

• 한국고분자학회지:고분자과학과기술
• /
• 제24권5호
• /
• pp.481-487
• /
• 2013

• Biomaterials and Biomechanics in Bioengineering
• /
• 제2권2호
• /
• pp.85-96
• /
• 2015

This study developed biodegradable bi-layered drug-eluting beads and investigated the in-vitro release of fluorouracil and cisplatin from the beads. To manufacture the drug-eluting beads, poly[(d,l)-lactide-co-glycolide] (PLGA) with lactide:glycolide ratios of 50:50 and 75:25 were mixed with fluorouracil or cisplatin. The mixture was compressed and sintered at $55^{\circ}C$ to form bi-layered beads. An elution method was employed to characterize the release characteristic of the pharmaceuticals over a 30-day period at $37^{\circ}C$. The influence of polymer type (i.e., 50:50 or 75:25 PLGA) and layer layout on the release characteristics was investigated. The experiment suggested that biodegradable beads released high concentrations of fluorouracil and cisplatin for more than 30 days. The 75:25 PLGA released the pharmaceuticals at a slower rate than the 50:50 PLGA. In addition, the bi-layered structure reduced the release rate of drugs from the core layer of the beads. By adopting the compression sintering technique, we will be able to manufacture biodegradable beads for long-term drug delivery of various anti-cancer pharmaceuticals.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2002년도 춘계학술발표대회 논문집
• /
• pp.203-206
• /
• 2002

The present study proposes a theoretical model for predicting the matrix crack density growth of each layer in composite laminates subjected to thermo-mechanical loads. Each layer with matrix cracks is treated as an equivalent continuum of degraded elastic stiffnesses which are functions of the matrix crack density in each slyer. The energy release rate as a function of the degraded elastic stiffnesses is then calculated for each layer as functions of thermo-mechanical loads externally applied to the laminate. The matrix crack densities of each layer in general laminates are predicted as functions of the thermo-mechanical loads applied to a number of laminates. Comparisons of the present study with experimental data in the open literatures are also provided.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.725-730
• /
• 1996

The key process in silicon surface micromachining is the selective etching of a sacrificial layer to release the silicon microstructure. The newly developed anhydrous HF/$CH_3$OH gas phase etching of TEOS (teraethylorthosilicate) sacrificial layers onto the polysilicon and the nitride substrates was employed to release the polysilicon microstructures. A residual product after TEOS etching onto the nitride substrate was observed on the surface, since a SiOxNy layer is formed on the TEOS/nitride interface. The polysilicon microstructures are stuck to the underlying substrate because SiOxNy layer does not vaporize. We found that the only sacrificial etching without any residual product and stiction is TEOS etching onto the polysilicon substrate.