• Structural Engineering and Mechanics
• /
• v.28 no.1
• /
• pp.19-38
• /
• 2008

A general solution to the field equations of homogeneous isotropic generalized thermoelastic diffusion with two relaxation times (Green and Lindsay theory) has been obtained using the Fourier transform. Assuming the disturbances to be harmonically time.dependent, the transformed solution is obtained in the frequency domain. The application of a time harmonic concentrated and distributed loads have been considered to show the utility of the solution obtained. The transformed components of displacement, stress, temperature distribution and chemical potential distribution are inverted numerically, using a numerical inversion technique. Effect of diffusion on the resulting expressions have been depicted graphically for Green and Lindsay (G-L) and coupled (C-T) theories of thermoelasticity.

• Structural Engineering and Mechanics
• /
• v.5 no.3
• /
• pp.307-327
• /
• 1997

This paper is concerned with the time dependent service load behaviour of prestressed composite tee beams. The effects of creep and shrinkage of the concrete slab are modelled using the age adjusted effective modulus method and a relaxation approach. The tendon strain is determined considering compatibility of deformations and equilibrium of forces between the tendon and the composite tee beam. A parametric study is undertaken to study the influence of various aspects on the stress, strain and deformations of the concrete slab, steel beam and prestressing tendon. The effect of loading type and tendon relaxation has also been considered for various types of prestressing tendon materials. Recommendations are then made in relation to adequate span to depth ratios for varying levels of prestressing force.

• Transactions of Materials Processing
• /
• v.6 no.2
• /
• pp.102-109
• /
• 1997

The multistage deformation and stress relaxation were carried out to investigate the strain induced precipitation by torsion tests in the range of 1000~80$0^{\circ}C$, 0.05~5/sec for V-microalloyed steel. The starting temperature and time for the initiation of precipitation were determined by stress relaxation tests. The distribution of precipitates increased, as the strain rate increased and the mean size of precipitates was found to be about 10~30nm. The precipitation starting time$(P_s)$ decreased with increasing strain rate and the amount of pre-strain. The effect of deformation conditions on the no-recrystallization temperature$(T_nr)$ was also determined in the multistage deformation. $T_nr$ Tnr decreased with increasing the strain and strain rate. In the controlled rolling simulation, grain refinement and precipitation hardening effects could be achieved by the alternative large pass strain at the latter half pass stage under the condition of low temperature and high strain rate.

• Progress in Superconductivity and Cryogenics
• /
• v.20 no.1
• /
• pp.1-10
• /
• 2018

The improvement of critical current properties of $REBa_2Cu_3O_{7-x}$ (REBCO) coated conductors by introducing artificial pinning centers (APCs) is examined with respect to the field-angle anisotropy, high-field performance and relaxation property with time. Nano-rods along the c-axis introduced by PLD method and isotropic nano-particles introduced by TFA-MOD method are treated. The theoretical analysis is also shown to understand the effect of APCs quantitatively. The effects of superconducting layer thickness that influences the high-field performance and relaxation property are also discussed. It is shown that the upper critical field, which is another important factor to determine the high-field property, can be improved by introduction of APCs through electron scattering at interfaces with the superconducting matrix. The optimum critical current property can be obtained by properly designing the morphology and number density of APCs and the superconducting layer thickness.

• Structural Engineering and Mechanics
• /
• v.34 no.3
• /
• pp.285-300
• /
• 2010

The two-dimensional deformation of a homogeneous, isotropic thermoelastic half-space with voids with variable modulus of elasticity and thermal conductivity subjected to thermomechanical boundary conditions has been investigated. The formulation is applied to the coupled theory(CT) as well as generalized theories: Lord and Shulman theory with one relaxation time(LS), Green and Lindsay theory with two relaxation times(GL) Chandrasekharaiah and Tzou theory with dual phase lag(C-T) of thermoelasticity. The Laplace and Fourier transforms techniques are used to solve the problem. As an application, concentrated/uniformly distributed mechanical or thermal sources have been considered to illustrate the utility of the approach. The integral transforms have been inverted by using a numerical inversion technique to obtain the components of displacement, stress, changes in volume fraction field and temperature distribution in the physical domain. The effect of dependence of modulus of elasticity on the components of stress, changes in volume fraction field and temperature distribution are illustrated graphically for a specific model. Different special cases are also deduced.

• Journal of Biosystems Engineering
• /
• v.15 no.3
• /
• pp.207-218
• /
• 1990

Grains display characteristics of both elastic bodies and viscous fluids when they are subjected to mechanical treatments in harvesting, handling, and processing. This viscoelastic behavior of grains when mechanically stressed must be fully understood to establish maximum machine efficiency and have a minimum degree of grain damage and the highest quality of the final product. The studies were conducted to examine the effect of the moisture content, the loading rate and the initial deformation on the stress relaxation behavior of whole kernel of rough rice, and develop the rheological model to represent its stress relaxation behavior. The following results were obtained from the study. 1. Moisture content had the greatest influence on the initial portion of the relaxation curve. With elapsing time the lower moisture content resulted in the lower residual stress for the Japonica-type rough rice and vice versa for the Indica-type rough rice. But within the ranges of moisture content tested, the degree of stress relaxation per unit strain on the Indica-type rough rice was a little higher than those on the Japonica-type rough rice. 2. The slower loading rate resulted in less initial stress. The decreasing trend of residual stress for all the samples tested with increasing loading rate was shown. 3. The higher initial deformation for all the samples resulted in less initial stress. The increasing of amount of stress relaxation per unit strain with increase of initial stress indicated that viscoelastic properties of rough rice depended not only upon duration of load applied but also initial stress applied. This means that rough rice is nonlinear viscoelastic material. 4. The compression stress relaxation properties of rough rice kernel can be described by a generalized Maxwell model representing by the Maxwell elements.

• Journal of the Microelectronics and Packaging Society
• /
• v.21 no.4
• /
• pp.57-62
• /
• 2014

Using flexible bismaleimide-triazine co-polymer as a substrate, inkjet-printed Cu films were also investigated for low-cost and process feasibility of flexible electronics. After annealing at $200^{\circ}C$ for 1 h under various reducing ambient, surface color was changed to red and electrical resistivity was decreased to the level of conductor under formic acid ambient. However, its resistivity was much higher than conventional copper films due to surface crack. In order to reduce the residual film stress after annealing, additional isothermal treatment was inserted before anneal hiring the stress relaxation applied in processes of amorphous materials. As a result, no surface crack was observed and electrical resistivity of $3.4{\mu}{\Omega}cm$ was measured after annealing at $230^{\circ}C$ with stress relaxation while electrical resistivity of $7.4{\mu}{\Omega}cm$ was observed after normal annealing without relaxation. The effect of stress relaxation was also confirmed by observing surface crack after decreasing the relaxation time to 0 min.

• Bulletin of the Korean Chemical Society
• /
• v.4 no.1
• /
• pp.25-28
• /
• 1983

The effect of internal rotation of methyl group in liquid perdeuterotoluene on nuclear quadrupole relaxation of methyl deuterons is investigated. A model of a spherical diffusor undergoing rotational diffusion is extended to include the extended diffusion of internal rotation. The overall reorientational correlation time in the presence of internal rotation is explicitly given as an analytical function of the angular momentum correlation time. Also, the degree of inertial effect in the internal rotation is evaluated.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1994.10a
• /
• pp.368-373
• /
• 1994

Recently, a large number of box girder bridges with cantilevered decks have been constructed. Especially, segmentally erected prestressed concrete box girder bridges are widely used as economic and aesthetic solutions for long span bridges. Segmental erection is a particularly attractive construction alternative in cases where continuously supported formwork is impractical or uneconomical. In segmentally erected bridges, the structural systems are changed as the construction stages are progressive and redistribution of member forces occurs due to time dependent effects of concrete and relaxation of prestressing steel. Then, in segmentally erected bridges, analysis are required at each construction states. In this study, nonlinear analysis progam of the segmentally erected prestressed concrete box girder bridges is developed in taking into account nonlinearity of material and geometry, time dependent effect of concrete and relaxation of prestressing steel.

• Steel and Composite Structures
• /
• v.20 no.5
• /
• pp.1103-1117
• /
• 2016

The present investigation is to study the plane problem in initially stressed thermoelastic half-space with voids due to thermal source. Lord-Shulman (Lord and Shulman 1967) theory of thermoelasticity with one relaxation time has been used to investigate the problem. A particular type of thermal source has been taken as an application of the approach. Finite element technique has been used to solve the problem. The components of displacement, stress, temperature change and volume fraction field are computed numerically. The resulting quantities are depicted graphically for different values of initial stress parameter. The relaxation time and the initial stress parameter have a significant effect on all distributions.