• 토지주택연구
• /
• 제1권1호
• /
• pp.67-73
• /
• 2010

PHC 말뚝에서 강선을 노출시켜 건축물의 기초판과 연결시키는 기존 강선남김 방식은 강결합과 힌지결합의 중간형태로 공동주택(아파트)과 같은 건축구조물에 흔히 사용되는 방법이다. 그러나 이 방법은 역학적인 성능이 검증되지 않았으며 시공과정도 복잡하다. 이에 본 연구는 기존 관련 연구의 결과를 분석하고, PHC 말뚝의 콘크리트 단면적 대비 강선면적 비인 0.3%를 말뚝 접합부의 최소 철근보강량으로 선정하여 PHC 말뚝과 기초판과의 최적의 철근보강 방법을 말뚝 규격별(PHC 450, PHC 500, 및 PHC 600)로 제시하였다. PHC 말뚝과 기초판 접합부의 역학적 성능(인장강도와 전단강도)을 평가하기 위해 실물크기의 실험을 실시하였다. 그 결과, 모든 경우에 대해 요구강도를 만족하였으며 실제 적용되어도 문제가 없음을 확인하였다. 본 결과는 기존 연구에서 제시되었던 접합부의 철근 보강량보다 그 양이 대폭 감소하는 것으로 나타나 PHC 말뚝 시공 시 원가 절감에도 기여할 것으로 판단된다.

• Structural Engineering and Mechanics
• /
• 제61권6호
• /
• pp.711-719
• /
• 2017

This study investigates the effects of reinforcing bar diameter and cover depth on the shrinkage behavior of restrained ultra-high-performance fiber-reinforced concrete (UHPFRC) slabs. For this, twelve large-sized UHPFRC slabs with three different rebar diameters ($d_b=9.5$, 15.9, and 22.2 mm) and four different cover depths (h=5, 10, 20, and 30 mm) were fabricated. In addition, a large-sized UHPFRC slab without steel rebar was fabricated for evaluating degree of restraint. Test results revealed that the uses of steel rebar with a large diameter, leading to a larger reinforcement ratio, and a low cover depth are unfavorable regarding the restrained shrinkage performance of UHPFRC slabs, since a larger rebar diameter and a lower cover depth result in a higher degree of restraint. The shrinkage strain near the exposed surface was high because of water evaporation. However, below a depth of 18 mm, the shrinkage strain was seldom influenced by the cover depth; this was because of the very dense microstructure of UHPFRC. Finally, owing to their superior tensile strength, all UHPFRC slabs with steel rebars tested in this study showed no shrinkage cracks until 30 days.

• Steel and Composite Structures
• /
• 제21권6호
• /
• pp.1265-1285
• /
• 2016

This paper presents experimental results of advanced investigation carried out on the beams reinforced with Glass Fiber Reinforced Polymer (GFRP) rebar and stirrups. Twelve beams reinforced with GFRP and one beam with steel reinforcement of size $230{\times}300{\times}2000mm$ were investigated. Longitudinal reinforcement, shear span and spacing of stirrups were the main variables to form the set. In advanced testing three types of strain gauges for steel, composite and concrete surface were applied to observe strain/stress development against the applied load. Live data were recorded from four strain gauges applied on stirrups, one at center on longitudinal reinforcement, two on the concrete surface and central deflection during the test. Although the focus of the paper was mainly on the behavior of GFRP shear reinforcement, other parallel data were observed for the completeness of the test. Design recommendations of ISIS Canada Design Manual (2007), Japan Society of Civil Engineers (1997) and American Concrete Institute (ACI-440.1R-06) were reviewed. Shear design predictions were compared with experimental results in which it was observed that all the three standards provided conservative predictions. However, ACI found most efficient compare to other two there is room to improve the efficiency of the recommendations.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2000년도 춘계학술발표대회 논문집
• /
• pp.63-66
• /
• 2000

This paper describes the need for a ductile Fiber Reinforced Plastic(FRP) reinforcement for concrete structures. Using the material hybrid and geometric hybrid, it is demonstrated that the pseudo-ductility characteristic can be generated in FRP rebar. Ductile hybrid FRP bars were successfully fabricated at 4mm and l0mm nominal diameters using an hand lay up method. Tensile specimens from these bars were tested and compared with behavior of FRP rebar and steel bar

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2000년도 춘계학술대회 논문집
• /
• pp.57-62
• /
• 2000

This paper describes the need for a ductile Fiber Reinforced Plastic(FRP) reinforcement for concrete structures. Using the material hybrid and geometric hybrid. it is demonstrated that the pseudo-ductility characteristic can be generated in FRP rebar. Ductile hybrid FRP bars were successfully fabricated at 4mm and 10mm nominal diameters using an hand lay up method. Tensile specimens from these bars were tested and compared with behavior of FRP rebar and steel bar

• Architectural research
• /
• 제22권1호
• /
• pp.33-39
• /
• 2020

In this study, side-face blowout failure strength of high strength headed reinforcing bar, which is vertically anchoring between RC or SFRC members, is evaluated throughout pullout test. The major test parameters are content ratio of high strength steel fibers, strength of rebar, length of anchorage, presence of shear reinforcement, and the side concrete cover thickness planned to be 1.3 times of the rebar. In pullout test, tensile force was applied to the headed reinforcing bar with the hinged supports positioned 1.5 and 0.7 times the anchorage length on both sides of the headed reinforcing bar. As a result, the cone-shaped crack occurred where the headed reinforcing bar embedded and finally side-face blowout failure caused by bearing pressure of the headed reinforcing bar. The tensile strength of specimens increased by 13.0 ~26.2% with shear reinforcement. The pullout strength of the specimens increased by 3.6 ~15.4% according to steel fiber reinforcement. Increasing the anchoring length and shear reinforcement were evaluated to reduce the stress bearing ration of the total stress.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1999년도 학회창립 10주년 기념 1999년도 가을 학술발표회 논문집
• /
• pp.751-754
• /
• 1999

Corrosion inhibitors are widely used to protect chloride-induced corrosion of reinforcement in concrete. However, the number of researches on the corrosion of reinforcement, when corrosion inhibitor is used, is not enough for actual application in the field. In addition, on corrosion of reinforcement a quantitative standard about corrosion inhibitor does not exist and the data about its influencing concrete are relatively rare. In this study, the effectiveness of rebar corrosion protection, setting time, compressive strength, chloride ion's penetration, and diffusion test were performed using with three different kinds of corrosion inhibitors.

• 한국표면공학회지
• /
• 제52권6호
• /
• pp.364-370
• /
• 2019

Fe-Mn-Si-Ni-Cr-TiC alloys have a shape memory property, recovering initial shape by heating. With an aim to improve a durability and stability of building and infrastructure, this Fe-based shape memory alloy (FSMA) can be employed to reinforce concrete structure with creation of compressive residual stress. In this work, corrosion resistance of FSMA was compared with general rebar and S400 carbon steel to evaluate the stability in concrete environment. Potentiodynamic polarization test in de-ionized water, tap-water and 3.5 wt.% NaCl solution with variations of pH was used to compare the corrosion resistance. FSMA shows better corrosion resistance than rebar and S400 in tested solutions. However, Cl-containing solution is critical to significantly reduce the corrosion resistance of FSMA. Therefore, though FSMA can be a promising candidate to replace the rebar and S400 for the reinforcement of concrete structure, serious cautions are required in marine environments.

• 한국구조물진단유지관리공학회 논문집
• /
• 제19권2호
• /
• pp.40-51
• /
• 2015

콘크리트 구조물에서는 인장응력에 대한 저항과 콘크리트내의 하중전달을 위한 철근이음이 고려되어야 한다. 현재 사용되고 있는 철근의 이음방법으로는 전통적으로 사용되는 겹침이음과 함께 채움금속이음을 갖는 슬리브이음과 전조 평행나사 이음과 같은 기계적 철근연결방법 등이 사용되고 있다. 본 연구는 기존에 사용되고 있는 기계적 철근 이음의 시공성과 구조적 성능을 개선하기 위하여 전조 변단면 철근이음을 제안하고 이를 적용한 철근의 구조성능과 파괴거동을 평가하기 위하여 철근연결 종류 및 체결 특성을 고려한 인장강도 실험과 휨하중 실험을 실시하였다. 이를 통하여 제안된 전조 변단면 이음을 적용한 철근의 인장강도 및 휨성능을 비교 평가하였다. 본 연구결과 전조변단면 이음을 적용한 철근이 이음이 없는 철근과 비교하여 동일한 구조성능을 가지는 것으로 나타나 철근콘크리트 구조물의 철근 이음을 위하여 사용할 수 있을 것이다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제25권6호
• /
• pp.131-142
• /
• 2021

노후 교각은 내진설계가 적용되지 않아 소성힌지구역에 겹침이음이 대다수 존재한다. 철근부식은 철근 단면적 감소 및 겹침이음부의 거동저하를 유발하여 교각의 내진성능을 저하시킨다. 본 연구에서는 이러한 노후교각의 특성에 따라 철근부식, 겹침이음, 내진설계 및 내진 보강 여부를 고려하여 실험체를 설계 및 제작하고 실험을 통해 그 영향을 조사하였다. 실험결과, 겹침이음 또는 철근부식은 변위연성도를 감소시킨다. 내진설계 상세 또는 강판 내진보강을 적용하면 충분한 변위연성도가 확보됨을 확인하였다. 모든 비내진실험체는 소성힌지구역 내의 횡철근 겹침이음부의 풀림으로 인해 주철근 좌굴과 심부콘크리트 압축파쇄가 발생하였다. 내진설계된 실험체는 철근부식에 의한 소성힌지구역 내 횡철근의 단면감소와 갈고리 풀림에 의해 주철근 좌굴 및 심부콘크리트 압축파쇄가 발생하였다.