• Environmental Engineering Research
• /
• v.22 no.2
• /
• pp.169-174
• /
• 2017

Vacuum swing adsorption (VSA) is a promising treatment method for volatile organic compounds (VOCs). This study focuses on a VSA process for regenerating activated carbon spent with VOCs, and then investigates its adsorption capacities. Toluene was selected as the test VOC molecule, and the VSA regeneration experiments results were compared to the thermal swing adsorption process. Cyclic adsorption-desorption experiments were performed using a lab-scale apparatus with commercial activated carbon (Samchully Co.). The VSA regeneration was performed in air (0.5 L/min) at 363.15 K and 13,332 Pa. The comparative results depicted that in terms of VSA regeneration, it was found that after the fifth regeneration, about a 90% regeneration ratio was maintained. These experiments thus confirm that the VSA regeneration process has good recovery while operating at low temperatures (363.15 K) and 13,332 Pa.

• Journal of the Korean Applied Science and Technology
• /
• v.34 no.4
• /
• pp.947-953
• /
• 2017

In this study, the regeneration efficiency of the amino acid salt absorbent which can be applied to carbon dioxide absorption / regeneration process was confirmed. The regeneration efficiency has a great influence on the economical judgment of the process. so, continuous regeneration experiment was conducted to establish economical process. The amino acid salts used in the experiments are Potassium L-lysinate and Potassium L-alaninate. Each amino acid and potassium hydroxide(KOH) were mixed at a 1: 2 molar ratio. In order to confirm the regeneration efficiency of the absorbent, carbon dioxide was absorbed in the two materials, and the carbon dioxide desorption experiment was carried out by heating. The initial reaction rate was L-alanine was faster. Over time, L-lysine, desorption higher concentrations of carbon dioxide. L-lysine showed higher regeneration efficiency than L-alanine, (L-alanine 47.26% and L-lysine 62.11%). As a result of the continuous regeneration experiment using the L-lysine having good absorption and regeneration efficiency, it was confirmed that the regeneration efficiency decreases as the number of regeneration increases.

• Design & Manufacturing
• /
• v.10 no.2
• /
• pp.1-5
• /
• 2016

High-speed and high-torque performance is required in the ultra-high speed electric injection molding machine field. To implement this performance, the big-size inverter is needed and the corresponding converter should be used. In this case, the whole cost for configuring the system will be increased. In this paper, we introduce a method which is able to reduce the energy and the cost for configuring the system using the energy regeneration. The energy regeneration method is based on reusing the regeneration power generated at the electric motor during decelerating the injection motion. In this paper, we demonstrate the effectiveness of the method by using the ultra-high speed injection motion.

• Clean Technology
• /
• v.16 no.4
• /
• pp.272-276
• /
• 2010

Adsorption process for the removal of acetylene, especially 2-butyne, from isoprene was studied with zeolite as an adsorbent. In this work, zeolite 5A was selected to investigate the effects of various regeneration conditions by repeated adsorption experiments. The effect of regeneration temperature and desorption pressure was investigated to identity the optimum regeneration conditions. Repeated adsorption and desorption experiments were carried out for 10 cycles to confirm the efficiency of regeneration process under temperature of 423 K and desorption time of 16 h.

• Current Applied Physics
• /
• v.18 no.12
• /
• pp.1600-1604
• /
• 2018

This paper reports on a systematic and quantitative assessment of light induced degradation (LID) and regeneration in full Al-BSF and passivated emitter rear contact cells (PERC) along with the fundamental understanding of the difference between the two. After LID, PERC cells showed a much greater loss in cell efficiency than full Al-BSF cells (~0.9% vs ~0.6%) because the degradation in bulk lifetime also erodes the benefit of superior BSRV in PERC cells. Three main regeneration conditions involving the combination of heat and light ($75^{\circ}C/1\;Sun/48h$, $130^{\circ}C/2\;Suns/1.5h$ and $200^{\circ}C/3\;Suns/30s$) were implemented to eliminate LID loss due to BO defects. Low temperature/long time ($75^{\circ}C/48h$) and high temperature/short time ($200^{\circ}C/30s$) regeneration process was unable to reach 100% stabilization. The intermediate temperature/time ($130^{\circ}C/1.5h$) generation achieved nearly full recovery and stabilization (over 99%) for both full Al-BSF and PERC cells. We discussed the effect of temperature, time and suns in regeneration mechanism for two cells.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.6
• /
• pp.689-695
• /
• 2018

This paper presents the means of controlling the regeneration of a diesel particulate filter (DPF) that is mounted on tactical vehicles to satisfy exhaust gas standards. The DPF captures particulate matter in the exhaust gas and combusts the captured particulate matter. This process is regeneration, which is essential to the normal performance of the DPF. Bad regeneration causes degradation of vehicle performance; worse, it can lead to a vehicle fire. DPF regeneration is performed by control logic. If the regeneration control logic does not properly reflect the operating characteristics of the vehicle, DPF regeneration may not occur. Consequently, it is very important to ensure the DPF operates properly by reflecting the operating characteristics of the tactical vehicle. This study analyzes the operational characteristics of a tactical vehicle and the DPF, and adds proper DPF regeneration control logic. Additionally, this study is intended to simultaneously improve the additional problems that may occur from operating under the added regeneration control logic.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.19 no.7
• /
• pp.521-528
• /
• 2007

The desiccant rotor is the most essential component of desiccant cooling system, but its design relies on manufacturer's experience and principles are not yet clear in spite of a lot of theoretical/experimental work published. The mathematical modeling of desiccant rotor needs solution of coupled partial differential equations of heat and mass transfer. In this study, numerical program is developed and validated using a real desiccant rotor. The calculation results are in reasonable agreement with the experimental data and other available numerical results. Optimization of desiccant rotor on the condition of low regeneration temperature are investigated. The optimal rotor speed at which the process outlet humidity becomes minimized, shows same as that of the system optimization. Compared to high regeneration temperature, broad is the range of optimal speed of low regeneration temperature. Systematic analysis on the optimal area ratio of regeneration to dehumidification section has also been conducted.

• Journal of Korean Society on Water Environment
• /
• v.29 no.6
• /
• pp.777-781
• /
• 2013

Ion-exchange technology is one of the best for removing nitrate from drinking water. However, problems related to the disposal of spent brine from regeneration of exhausted resins must be overcome so that ion exchange can be applied more widely and economically, especially in small communities. In this background, a combined bio-regeneration and ion-exchange system was operated in order to prove that nitrate-laden resins could be bio-regenerated through direct contact with denitrifying bacteria. A nitrate-selective A520E resin was successfully regenerated by denitrifying bacteria. The bio-regeneration efficiency of nitrate-laden resins increased with the amount of flow passed through the ion-exchange column. When the fully exhausted resin was bio-regenerated for 5 days at the flowrate of 30 BV/hr and MLSS concentration of $125{\pm}25mg/L$, 97.5% of ion-exchange capacity was recovered. Measurement of nitrate concentrations in the column effluents also revealed that less than 5% of nitrate was eluted from the resin during 5 days of bio-regeneration. This result indicates that the main mechanism of bio-regeneration is the direct reduction of nitrate by denitrifying bacteria on the resin.

• Plant Biotechnology Reports
• /
• v.4 no.2
• /
• pp.173-178
• /
• 2010

An efficient protocol for shoot regeneration was developed for sesame (Sesamum indicum L.) internodes using the transverse thin cell layer (tTCL) culture method. The frequency of shoot regeneration and the number of adventitious buds produced from regenerated shoots depend significantly on explant age, thickness of the tTCL sections, and the phytohormones supplemented to the culture medium. A combination of 6-benzyladenine (2.0 $mg\;l^{-1}$) and a-naphthaleneacetic acid (0.5 $mg\;l^{-1}$) was found to be the best phytohormone combination for shoot bud induction, with the maximum number of shoots obtained when the tTCL sections were 0.5-1.0 mm thick and derived from 4- to 6-week-old seedlings of sesame. Well-developed shoots were rooted on MS medium without phytohormones, and 80% of the regenerated plantlets were successfully established in soil.

• Clean Technology
• /
• v.23 no.2
• /
• pp.140-147
• /
• 2017

In this study, we performed numerical simulation for the catalyst regeneration process of diesel desulfurization reactor. We analyzed the changes in regeneration process according to purge gas flow rate, catalyst permeability, reactor size, and heat loss of reactor. We have found that the regeneration process is very much affected by temperature changes whereas it is hardly affected by catalyst permeability and porosity. We also estimated the regeneration time according to purge gas flow rate and initial temperatures and have found that increasing purge gas temperature is more effect for fast regeneration. The present results can be utilized to design a regeneration process of diesel desulfurization reactor for a fuel cell used in ships. Furthermore, the present work also can be used to design low sulfur diesel supply in oil refineries and therefore contribute to the development of clean petrochemical technology.