• Proceedings of the Korea Water Resources Association Conference
• /
• 2007.05a
• /
• pp.2113-2116
• /
• 2007

In this study, transmission and reflection of multi-directional random waves propagating over multi-arrayed submerged breakwaters are investigated using eigenfunction expansion method. The numerical analysis on the wave energy reflection of submerged breakwaters with various crown widths is carried out. Strong wave reflection is occurred at the Bragg reflection condition of the peak frequency. When relative heights and crown widths of breakwaters are equal to 0.6 and 0.4h, respectively, more than 25% of wave energy is reflected to off shore.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.392-399
• /
• 2005

Shear modulus (or rigidity) of dam material is an important parameter which can be directly associated with the deformation of dam. Seepage or leakage of water can cause the defects or cracks of dam body. The existence of cracks and rigidity of dam body are decisive information for the estimation of dam safety. Rigidity of material is mainly determined from S-wave velocity and the defects of dam body can be detected by seismic reflection survey. Therefore, seismic reflection survey will be a desirable method which can give a solution about dam safety problem. Among various physical properties of dam body, S-wave velocity is the most important information but it is not easy to get the information. In this study, diverse measuring techniques of S-wave reflection survey were attempted to get the information about S-wave velocity of dam body. Ultimately, S-wave velocity could be estimated by the analysis of SH reflection events which can be easily observed in shot gather data obtained from SH measuring technique. Meanwhile, P-wave reflection survey was also performed at the same profile. P-beam radiation technique which can reduce the surface waves and reinforce the P-wave reflection events was applied for giving a help to analyse P-wave velocity. In the end, P-and S-wave velocity, Vs/Vp, Poisson's ratio distribution of the vertical section under the profile could be acquired.

• The Journal of Korean Association of Computer Education
• /
• v.22 no.5
• /
• pp.27-37
• /
• 2019

In this study, for the purpose of reflection level analysis of high school students in HW design learning which is based on online simulation, we carried out 5 lessons of HW learning and analyzed there reflection levels for 5 individual time of reflection content. The reflection level analysis results for each time of learning shows that the reflection level of the $3^{rd}$ time learning of D-Flip Flop is the highest score with 1.23. The correlation analysis result between the reflection contents presents that high positive correlation between learning content and task resolving method(r=.781, p<.01), and negative design correlation between task resolving method and alternative resolving method. The HW learning satisfaction survey result shows 4.2, and most of the participant students provided opinions that the HW design learning is required and current learning contents is a bit difficult to follow. We could recognize HW design learning is required to have composition of curriculum with basic and advanced contents, and on-off lines combined.

• Journal of Mechanical Science and Technology
• /
• v.15 no.2
• /
• pp.160-171
• /
• 2001

Depending upon the method of the surface generation and the quality of the designed boundary curves, the resulting surfaces may have global or local irregularities in many cases. Thus, it would be necessary for the designer to evaluate the surface quality and to modify the surface. This is very important because the defect of the surface causes the rework of the dies, increasing cost and delivery time significantly. To simulate the reflection line test in the actual production line, a faster algorithm for generating reflection lines is presented. In this paper, among various surface interrogation methods using reflection lines, Blinn-Newell type of reflection mapping is applied to generate the reflection lines on the trimmed NURBS surfaces. The derivation of reflection lines is formulated as a surface-plane intersection problem (Jung 1994) and is solved by surface-contouring techniques. Also, for eliminating the discontinuity of reflection lines due to the configuration of reflection map, a modified reflection map is proposed. An efficient traced contouring technique is utilized for the computational efficiency and proves to be well suited for the real-time quality-assessment task.

• Smart Structures and Systems
• /
• v.32 no.4
• /
• pp.253-266
• /
• 2023

The time-reversal method is employed to improve the ability of pipeline defect detection, and a new approach of identifying the pipeline defect depth is proposed in this research. When the L(0,2) mode ultrasonic guided wave excited through a lead zirconate titinate (PZT) transduce array propagates along the pipeline with a defect, it will interact with the defect and be partially converted to flexural F(n, m) modes and longitudinal L(0,1) mode. Using a receiving PZT array attached axisymmetrically around the pipeline, the L(0,2) reflection signal as well as the mode conversion signals at the defect are obtained. An appropriate rectangle window is used to intercept the L(0,2) reflection signal and the mode conversion signals from the obtained direct detection signals. The intercepted signals are time reversed and re-excited in the pipeline again, result in the guided wave energy focusing on the pipeline defect, the L(0,2) reflection and the L(0,1) mode conversion signals being enhanced to a higher level, especially for the small defect in the early crack stage. Besides the L(0,2) reflection signal, the L(0,1) mode conversion signal also contains useful pipeline defect information. It is possible to identify the pipeline defect depth by monitoring the variation trend of L(0,2) and L(0,1) reflection coefficients. The finite element method (FEM) simulation and experiment results are given in the paper, the enhancement of pipeline defect reflection signals by time-reversal method is obvious, and the way to identify pipeline defect depth is demonstrated to be effective.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.3
• /
• pp.416-420
• /
• 2008

This paper proposes a new method to improve signal characteristics at branches frequently met in system-level routing. We also introduce the numerical formula which can estimate the time delay due to branches and the simple design guideline for system-level routing. Finally, we propose the routing method which can eliminate the signal reflection for the case of one driver and two receivers (multi-drop topology).

• Journal of the Optical Society of Korea
• /
• v.18 no.6
• /
• pp.672-678
• /
• 2014

We propose a method to estimate the 3-D shape of surfaces with specular reflection, using a model of the difference in appearance between images reflected from a flat surface and a curved surface. First, we analyze the geometry of spatial reflection from a specular surface and how reflected light varies due to a curved surface. This is used to estimate 3-D shape. The proposed method is shown to be effective in experiments using illumination from spatially distributed light sources and a camera capturing the reflected light from curved, specular surfaces.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.12
• /
• pp.1940-1946
• /
• 1989

A design method of lossy interstage networks for broadband microwave amplifiers is presented. A lossy interstage network is assumed as the combination of two lossless networks between which a lossy serial impedance or a lossy parallel admittance is inserted. For the circuit with two transistors and a lossy element, realizable ranges of gain and reflection coefficients are derived. And the relationships between gain and reflection coefficients are derived. Illustrative examples are presented by using the proposed method.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.20 no.4
• /
• pp.370-378
• /
• 1987

Wave reflection control functions of mound for the foundation of composite and perforated break-waters were investigated through the theoretical considerations. The theory developed is based on a simple summation of components of reflected waves. The applicability of the theory is assured by the comparative studies of the theoretical calculation and experimental data on the sea surface elevation in front of a breakwater. It is found that the reflection is mainly controlled by depth and width of the mound. In the design of composite type perforated breakwaters, the width of perforated part of the upright section can be decreased to less than half of the conventional design width for the same reflection by using the reflection control function of mound part and the reflection can be reduced until less than $30\%$ of that in the composite breakwaters. Using the results, a design method of mounds is proposed, by which the reduction of wave reflection is assured under the given wave conditions.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.15 no.3
• /
• pp.143-150
• /
• 2003

Based on the eigenfunction expansion method, the interaction between monochromatic waves and a partially immersed slotted plate with a back wall has been investigated. Analytical results show that the reflection coefficients by a partially immersed slotted plate depend on the porosity, immersed depth, chamber width, incidence angle and wave frequency. It is found that the reflection coefficient has minimum value within entire frequency range when the porosity has optimal value 0.1. Comparison between the analytical results and the experimental results(Zhu,2001) of reflection coefficients is made for various chamber widths, immersed depths and wave periods with good agreement. The present analytic method can account adequately for energy dissipation caused by flow separation behind a slotted plate and provide the design informations for the construction of slit caisson breakwater.