• 지구물리와물리탐사
• /
• 제19권4호
• /
• pp.220-227
• /
• 2016

해양 탄성파 탐사를 통해 취득한 자료에는 지하 매질에서 반사되어 오는 신호뿐만 아니라 해수면에서 되반사되어 발생하는 고스트가 존재한다. 고스트는 특정 주파수 성분을 약화시켜 탄성파 자료의 시간 해상도를 저하시킨다. 고스트를 효과적으로 제거하기 위해서는 정확한 고스트의 지연시간과 해수면의 반사계수가 요구된다. 고스트 지연시간은 해수면의 상하 움직임, 에어건과 스트리머의 움직임 및 벌림(offset) 거리 등에 의해 변하며, 해수면의 반사계수도 주파수, 평면파의 입사각 그리고 해상 상태에 따라 변한다. 이러한 영향을 고려한 고스트 지연시간을 추정하기 위하여 이 연구에서는 고스트 제거 트레이스 및 이의 자기상관 자료의 L-1 norm, L-2 norm 그리고 첨도(kurtosis)를 비교하였다. 자기상관자료의 L-1 norm을 계산하여 고스트 지연시간을 추정하는 것이 오차가 가장 적게 발생하였다. 현장자료의 파고를 고려하고 키르히호프 근사식을 이용하여 해수면의 반사계수를 계산하여 음원 및 수신기 고스트 제거에 적용하였다. 고스트를 제거함으로써 약화된 주파수 성분을 복원하였으며 시간 해상도가 향상된 구조보정 단면을 얻었다.

• 대한조선학회논문집
• /
• 제50권6호
• /
• pp.458-465
• /
• 2013

Ship design engineering refers to the development and design of shipbuilding architectures in a drawing which reflects all relevant manufacturing processes. This paper provides analysis methods for model-information interfaces between hull structure design and outfitting design, and a technical application for manufacturing phases reflecting the pipe support pad and angle item automatically. The existing information procedure of pipe support pad and angle system processes information using drawing without model specification. Outfitting design team directly distributes drawings to the shop floor then manual-based marking and installation work are conducted refer to the distributed drawings. As a result, this process has become time consuming and causes problems in the productivity and quality improvement due to the rework caused by omitted or incorrect marking. The pipe support pad and angle marking is a method that automatically updates model information to hull structure design using sets of data that analyse the generated model in outfitting design processes. Therefore, this approach provides an efficient solution through design references without manual activities such as a reflection of hull structure design, cutting process, numerical control work, and dimension measurement and marking. The conversion of a method from the existing procedure based on manual marking to the reflective and automatic approach would have enabled to proceed installation work without manual activities for the measurement. Therefore, this research study proposes an efficient approach using pre-data analysis of model information interfaces between design and manufacturing phases to improve productivity during construction for shipbuilding.

• KIEAE Journal
• /
• 제14권6호
• /
• pp.5-13
• /
• 2014

Various studies on lighting energy savings are conducted, given that lighting energy consumption accounts 23.5% of building energy consumption. Especially, external type light shelf's efficiency is acknowledged; however, its application is limited in Korea, where high rise building ratio is high, due to high wind pressure. This study delves into natural lighting system to cope with wind pressure, and proposes the punching plate-installed light shelf. This study actually draws lighting energy output, according to whether the punching plate is applied through the test-bed, and verifies the effectiveness of the punching plate-installed light shelf. The conclusion is presented below: First) The result of performance evaluation of light shelf with the punching plate in winter solstice showed that the awning area decreased as the opening ratio increased so that the indoor distributed illumination tended to increase, and $-40^{\circ}$ which was advantageous for awning was determined as the proper angle. Second) The light shelf with the punching plate in spring/autumn equinox shows improved lighting according to the angle, and the appropriate angle of light shelf with the punching plate has increased to $15^{\circ}$ and $20^{\circ}$ according to the opening ratio in comparison to $5^{\circ}C$ which is the appropriate angle of light shelf with no punching plate due to the reflection area reduced by the reflecting plate with holes. Third) The result of performance evaluation of light shelf with the punching plate in summer solstice showed that the lighting performance tended to decrease as the opening ratio increased. 4) The light shelf with the punching plate incurs a 50% energy loss in comparison to the light shelf with no punching plate. However, its effectiveness has been proven in the aspects that it can bring a 50% energy saving in comparison to the case with no installation of light shelf and that it can be designed in response to wind pressure on the high floors.

• 한국전자파학회논문지
• /
• 제19권9호
• /
• pp.1020-1027
• /
• 2008

본 논문에서는 드루드 모형(Drude model) 특성을 가지는 메타 물질의 굴절각 및 임계각을 해석적으로 분석하였다. 메타 물질 슬래브(slab)에서의 전자기파의 반사 및 투과 특성을 해석하기 위해 메타 물질에서 적용된 드루드 모형에서는 30 GHz에서 각각 -1의 값을 갖는 유전율, 투자율을 사용하였다. 해석 결과로부터 드루드 모형에서 물리 상수(physical constant)의 부호가 주파수에 따라 연속적으로 변하기 때문에 주파수 대역별로 굴절각과 임계각이 각각 서로 다른 특성을 갖는다는 사실을 유도하였다. 본 논문에서 유도한 메타 물질의 주파수에 따른 굴절각 및 임계각 특성은 메타 물질의 주파수와 물리 상수간의 특성과 같은 전자기적 특성을 이해하고, 메타물질과 유전체간 다층 결합의 전파 특성 해석, 레이돔에 적용 가능한 신소재 메타 물질, 전기적 초소형 안테나와 같은 다양한 전자기파 응용에 유용하게 사용할 수 있다.

• 소성∙가공
• /
• 제14권3호
• /
• pp.282-290
• /
• 2005

Nowadays, TFT-LCD is widely used as display unit of many digital devices. And, the backlight unit(BLU) is used as a light source of TFT-LCD module. In the backlight unit, the most important component is a light guide, which guides the input light to the TFT-LCD module uniformly. Recently, many researchers have focused on improving the efficiency of BLU by changing the design and structure of a light guide. In the present paper, a series of simulation was performed to find the optimal luminance distribution of emanated light from the given geometry as the first step. From the results of simulations for the light guide with given V-groove pattern, the emanated light from it is mostly affected by the groove angle. In the case of acute angle, about 74 degrees was found as optimal angle to satisfy the restrictions of angular luminance distribution, FWHM, the maximum luminance, etc. However, as far as the average luminance value was concerned, the case of 120 degrees(abtuse angle) was found to be the best while prism films were added to the BLU. As a next step the light guide samples of 74 and 120 degrees were manufactured by DSF method, which was recently proposed by the authors. Of course, most of design parameters were chosen by the aid of simulation results. Finally, the results of average luminance values were compared between the simulation and DSF molded samples.

• 대한전자공학회논문지SD
• /
• 제48권9호
• /
• pp.6-12
• /
• 2011

본 논문에서는 장거리, 저 손실 FTTH 구성에 필요한 현장조립 광커넥터(FIOC)의 접속 신뢰성과 성능 향상을 위한 방법을 제시한다. 이를 위해 FIOC의 내부 광섬유(inner fiber)와 외부 광섬유(field fiber)의 접속 면 각도를 최적화하여 별도의 각도 맞춤 툴과 광섬유 유각 절단기(fiber angled cleaver) 없이 조립하여도 저 손실 접속이 가능하도록 하였다. FIOC의 내부 광섬유(inner fiber)의 각도를 angled cleaver를 이용해 $2^{\circ}$로 고정하고, 외부 광섬유(field fiber)는 일반 광섬유 절단기를 이용해 오차를 포함해서 $0^{\circ}{\sim}1^{\circ}$의 각도로 서로 접속하여 삽입손실은 0.3dB 이내로 줄이고, 반사손실은 -60dB 이하를 유지 할 수 있도록 하였다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.174-174
• /
• 2014

Memristor devices are one of the most promising candidate approaches to next-generation memory technologies. Memristive switching phenomena usually rely on repeated electrical resistive switching between non-volatile resistance states in an active material under the application of an electrical stimulus, such as a voltage or current. Recent reports have explored the use of variety of external operating parameters, such as the modulation of an applied magnetic field, temperature, or illumination conditions to activate changes in the memristive switching behaviors. Among these possible choices of signal controlling factors of memristor, photon is particularly attractive because photonic signals are not only easier to reach directly over long distances than electrical signal, but they also efficiently manage the interactions between logic devices without any signal interference. Furthermore, due to the inherent wave characteristics of photons, the facile manipulation of the light ray enables incident light angle controlled memristive switching. So that, in the tautological sense, device orienting position with regard to a photon source determines the occurrence of memristive switching as well. To demonstrate this position controlled memory device functionality, we have fabricated a metal-semiconductor-metal memristive switching nanodevice using ZnO nanorods. Superhydrophobicity employed in this memristor gives rise to illumination direction selectivity as an extra controlling parameter which is important feature in emerging. When light irradiates from a point source in water to the surface treated device, refraction of light ray takes place at the water/air interface because of the optical density differences in two media (water/air). When incident light travels through a higher refractive index medium (water; n=1.33) to lower one (air; n=1), a total reflection occurs for incidence angles over the critical value. Thus, when we watch the submerged NW arrays at the view angles over the critical angle, a mirror-like surface is observed due to the presence of air pocket layer. From this processes, the reversible switching characteristics were verified by modulating the light incident angle between the resistor and memristor.

• 한국광학회지
• /
• 제14권4호
• /
• pp.399-405
• /
• 2003

FD10 유리를 이용한 클램프형 광전류 센서를 제작하였다. 대칭형 구조로 이루어진 2조각의 FD10유리를 이용하여 제작하였으며, 센서헤드 내부에서 반사시에 위상차가 발생하는 것을 방지하기 위해 정확히 임계각으로 광이 진행하도록 구조를 설계하였다. 제작한 광-전류 변류기 헤드를 이용하여, 0-1,000 AT 까지의 전류를 측정하고, 빛의 입사각에 따른 광의 손실, 입사광의 편광회전에 따른 광출력변화, 온도에 따른 출력의 변화 및 장시간 전류 측정 등에 대한 실험결과를 제시하고 이에 대한 분석을 통해 제작된 광전류 변류기 헤드의 전류계로서의 가능성을 입증하였다.

• 한국전자파학회논문지
• /
• 제13권4호
• /
• pp.351-358
• /
• 2002

본 논문에서는 구형 도파관내에 경사진 두 금속봉을 근사화한 구조에 모드 매칭법과 일반 산란계수법을 적용하여 이들의 경사 각도에 따른 상호 작용에 의한 산란 특성을 구할 수 있었다. 여기서 경사진 두 금속봉 구조에 모드 매칭법을 적용하기 위하여 적당한 개수의 모드를 택하여 경사각도에 대한 산란특성을 구하였다. 그리고, 이들의 경사진 두 금속봉의 계산 과정을 도파관과 동축선로의 접합부에 적용하여서 산란 특성을 얻을 수 있었다. 이런 결과에 따라서 경사 각도가 50$^{\circ}$ 일 경우에 동축 선로와 도파관 출력 포트로의 전달 특성이 3 ㏈가 되는 것을 알 수 있었다. 그리고, 입력단의 반사 손실은 경사 각도에 따라서 선형적으로 감소하는 특성을 얻을 수 있었다.

• 대한기계학회논문집B
• /
• 제20권9호
• /
• pp.2933-2943
• /
• 1996

A grating composed of elliptical cylinders (GEC), specially designed, is applicable to control of radiation heat transfer from a heated surface, as reported in our previous work. In this study, an analysis of radiation heat transfer is performed for a physical model in which the GEC is placed in front of a heated black-base surface and the major axes of the elliptical cylinders are inclined as a certain angle from the normal to the row of elliptical cylinders. Numerical solutions are obtained. Variations of the direction and the radiative energy concentration with slant angle of the major axis are shown for some parameters. It is verified that the GEC is able to widely change the direction of radiation heat transfer from the heated surface.