• 제어로봇시스템학회:학술대회논문집
• /
• 2002.10a
• /
• pp.104.5-104
• /
• 2002

In this paper, we focus on a configuration control method of a redundant manipulator. The configuration of a redundant manipulator has been determined by geometry constraints and additional conditions, such as obstacle avoidance and dexterity optimization. This paper also utilizes optimization, and the additional condition (or performance index) to be optimized is stiffness of the end-effector and joints' torque. Stiffness and torque may be a natural attribute to be controlled during working and those vary as manipulator configuration does. So the optimal configuration from the viewpoint of stiffness and joint torque is studied. If the servo control mechanism of the joints Is assumed to be a...

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.29B no.10
• /
• pp.27-36
• /
• 1992

This paper proposes a numerical method of motion planning for manipulators using Foruier series. For a redundant manipulator, we predetermine the trajectories of redundant joints in terms of the Nth partial sum of the fourier series. then the optimal coefficients of the fourier series are searched by the Powell's method. For a nonredundant or redundant manipulator, CS02T-continuous smooth joint trajectory for a point-to-point task can be obtained while considering the frequency response. We apply the proposed method to the 3-link planar manipulator and the PUMA 560 manipulator. To show the validity of the proposed method, we analyze solutions by the Fast Fourier Transform (FFT). Also, several features are discussed to obtain an optimal solution.

• Journal of information and communication convergence engineering
• /
• v.3 no.1
• /
• pp.33-37
• /
• 2005

One of the most important feature of the Mobile Manipulator is redundant freedom. Using the redundant freedom, Mobile Manipulator can move various mode, perform dexterous motion. In this paper, to improve robot job ability, as two robots perform a job in co-operation control, we studied optimal position and posture of Mobile Manipulator with minimum movement of each robot joint. Kinematics of mobile robot and task robot is solved. Using mobility of Mobile robot, weight vector of robots is determined. Using Gradient methode, global motion trajectory is minimized. so the job which Mobile Manipulator perform is optimized. The proposed algorithm is verified with PURL-II which is Mobile Manipulator combined Mobile robot and task robot. and discussed the result.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.18 no.6
• /
• pp.787-796
• /
• 2008

When the manipulator collides with surroundings, there occurs an impulse. To reduce the impulse, the self motion should maintain the manipulator's position by the minimally effective mass. At this time, we can use the local joint torque minimization algorithm to resolve the redundancy. In this study, to reduce the impulse and damages by the impact between the manipulator and surroundings, new control algorithm for the minimization of the joint torque using the kinetic redundancy and the impact minimization is proposed. It adapts fuzzy logic and genetic algorithm to the conventional local joint torque minimization algorithm. The proposed algorithm is applied to a 3-DOF redundant planar manipulator. Simulation results show that the proposed algorithm works well.

• Advances in robotics research
• /
• v.1 no.2
• /
• pp.141-154
• /
• 2014

Redundant parallel manipulators have some advantages over the nonredundant parallel manipulators. It is important to determine how many additional branches should be introduced. This paper studies whether one or two additional branches should be added to a 3-DOF parallel manipulator by comparing the flexible deformation of a 3-DOF parallel manipulator with one additional branch and that with two additional branches. The kinematic and dynamic models of the redundant parallel manipulator are derived and the flexible deformation is investigated. The flexible deformation of the manipulators with one additional branch and two branches is simulated and compared. This paper is helpful for designers to design a redundantly actuated parallel manipulator.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.53 no.4
• /
• pp.235-245
• /
• 2004

In this paper, fault tolerant mechanisms are presented for a servo manipulator system designed to operate in a hot cell. A hot cell is a sealed and shielded room to handle radioactive materials, and it is dangerous for people to work in the hot cell. So, remote operations are necessary to handle the radioactive materials in the hot cell. KAERI has developed a servo manipulator system to perform such remote operations. However, since electric components such as servo motors may fail by radiation, fault tolerant mechanisms have to be considered. For fault tolerance of the servo manipulator system, duplication mechanism increasing the reliability of the transport's driving motors and reconfiguration algorithm accommodating the slave's motor failure have been presented. The reconfiguration algorithm recovering the end effector's motion in spite of one motor's failure is based on control allocation redistributing redundant axes. The constrained optimization method and pseudo inverse method have been adopted for control allocation. Simulation examples and real test results have been presented to verify the Proposed methods.

• Transactions on Control, Automation and Systems Engineering
• /
• v.2 no.1
• /
• pp.56-61
• /
• 2000

Majority of industrial robots are controlled by a simple independent joint control of joint actuators rather than complex controllers based on the nonlinear dynamic model of the robot manipulator. In this independent joint control scheme, the performance of actuator control is influenced significantly by the joint disturbance torques including gravity, Coriolis and centrifugal torques, which result in the trajectory tracking error in the joint control system. The control performance of a redundant manipulator under independent joint control can be improved by minimizing this joint disturbance torque in resolving the kinematic redundancy. A 3 DOF planar robot is studied as an example, and the dynamic programming method is used to find the globally optimal joint trajectory that minimize the joint disturbance torque over the entire motion. The resulting solution is compared with the solution obtained by the conventional joint torque minimization, and it is shown that joint disturbance can be reduced using the kinematic redundancy.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.740-745
• /
• 2005

This study is intended to build a controller of redundant manipulators with the simultaneous abilities of trajectory tracking and obstacle avoidance without any preparations of path planning to achieve full automation even for one production of one kind, while keeping the avoidance ability high and keeping its shape away from object to reduce the possibility that the manipulator crashes to the object. To evaluate the avoidance ability of the intermediate link, we proposed a scalar value of Avoidance Manipulability Shape Index(AMSI), which is independent of the obstacle's shape. On the other hand, the danger to crash to the obstacle is depending on the shape of the obstacle, which could be evaluated by the potential field set around the obstacle. This paper proposes control method of the manipulator's shape based on the AMSI to simultaneously avoid obstacles and keep the avoidance ability high with potential.

• Journal of Institute of Control, Robotics and Systems
• /
• v.3 no.5
• /
• pp.482-489
• /
• 1997

This paper presents the analysis of the kinematics and dynamics of redundant parallel manipulators, and provides design guides for advanced parallel mainpulators with high performance. Three types of redundancies are considered which include the redundancies in serial chain, joint actuation, and parallelism. First, the kinematic and dynamic models of a redundant parallel manipulator are obtained in both joint and Cartesian spaces, and the kinematic and dynamic manipulabilities are defined for the performance evaluation. The effects of the three types of redundancies on the kinematic and dynamic performance of a parallel manipulator are then analyzed and compared, providing a set of guides for the design of advanced parallel manipulators. Finally, the simulation results using planer parallel manipulators are given.

• Journal of Mechanical Science and Technology
• /
• v.19 no.spc1
• /
• pp.320-327
• /
• 2005

A new mechanism for hyper redundant manipulator (HRM) is presented, which comprises of serially assembled compound three-bar linkages (CTL). The CTL mechanism has some unique properties. This paper presents the forward and inverse kinematics of this mechanism and shows the simulation of the HRM havig 9 CTL units. The recursive algorithm of the inverse kinematics that the author originally developed is employed. It is fast and stable ; moreover, it enables us to obtain a solution in which the end-point of the HRM is controlled by a portion of joints. It also presents the method of the dynamical analysis. There exist kinematical constraints in the proposed closed linkage mechanism. In the dynamic analysis constraints are sufficiently sustained by the constraint stabilization method that the author developed. The mechanical structure of the HRM having some CTL units that is under construction is shown.