• Journal of Acupuncture Research
• /
• v.33 no.2
• /
• pp.135-150
• /
• 2016

Objectives : The aim of this study is to review the combination effects and adverse effects of Yerba Mate (Ilex paraguariensis) on the treatment of obesity. Methods : Four databases were searched, including Pubmed, National assembly library, RISS4u, and NDSL, for studies published before March 31, 2016 using the keywords 'yerba mate', 'Ilex paraguariensis', and those related to 'obesity'. Clinical trials, and both in vivo and in vitro studies were classified according to the following categories: publication year, nationality, types and composition of test compounds, combination effects, adverse effects, and safety. Results : A total of 16 articles (14 clinical trials, one in vivo, one in vitro) were included in the analysis. Combination effects were reported from six YGD (Yerba Mate, Guarana, Damiana, Zotrim), five Meltdown, one Shred-matrix, one DBX (DymaBurn Xtreme), one XSIII research study, and adverse effects were reported from two YGD (Zotrim), four Meltdown, one Shred-matrix and one MetEF research study. YGD and Shred-matrix increased satiety while YGD and MetEF had adverse gastrointestinal effects potentially due to guarana. Meltdown and Shred-matrix increased energy expenditure and fat oxidation and had the adverse effects of increased heart rate and blood pressure due to the thermogenic effect of caffeine and yohimbine. DBX increased resting energy expenditure but no difference was observed in respiratory exchange ratio. XSIII reduced body weight gain and food intake more than each of the extracts did on their own. Conclusion : Taken together, the combination effects and adverse effects differed according to the composition of test compounds and the ratio of ingredients. Multicomponent approaches should be used for treating multifactorial diseases such as obesity. As a general conclusion, there is a place for a combination of herbal components including yerba mate, based on the principle of Kun-Shin-Choa-Sa for the treatment of obesity.

• Korean Journal of Food Science and Technology
• /
• v.28 no.4
• /
• pp.696-701
• /
• 1996

For effective utilization of skipjack (Katsuwonus pelamis) cooking juice (SCJ), the SCJ was hydrolyzed with 0.5% neutrase at $50^{\circ}C$ for 1 hr, and the degree of hydrolysis was estimated to be 66.0% at this reaction condition. The hydrolysate was treated with charcoal and filtered under reduced pressure. The extract powder was prepared from the filtrate in a spray-dryer. The major free amino acids of the extract Powder were taurine (526.3 mg/100 g), glutamic acid (375.8 mg/100 g), phenylalanine (315.9 mg/100 g), and alanine (283.6 mg/100 g), and their content accounted for 55.4% of the total free amino acids (2,711.5 mg/100 g). Among the nucleotides and their related compounds, inosine was the major component with 76.29 mole/g. The content of betaine-N, total ceatinine-N, TMAO-N, and TMA-N were 72.2, 51.2, 10.3, and 6.9 mg/100 g, respectively. From the omission test, it was concluded that the major taste compounds of the extract powder were believed to be free amino acids such as glutamic acid and alanine. Organic acids and nucleotides and their related compounds acted an auxiliary role in the taste of the extract powder.

• Journal of the Korea Concrete Institute
• /
• v.24 no.5
• /
• pp.509-516
• /
• 2012

The aims of this research is to develop a fire resistant admixture to enhance high-pressured pumping of high-strength concrete (HSC) with a compressive strength of 60~80 MPa. Generally, the efficiency of HSC high-pressured pumping is dramatically reduced due to entanglement of short fibers added to prevent fire spalling. Therefore, the fire resistant admixture that can facilitate pumping of fire resistant HSC is urgently needed presently. The fire resistant HSC mix is comprised of Polypropylene fiber, Nylon fiber and Polymer powder. The test results showed that the slump-flow was improved by approximately 70% of the HSC without fire resistant admixture. However, the air void content was increased slightly due to the addition. The standard design compressive strength at 28-days was satisfied, while its flexural strength was similar to the concrete without the admixture. Since the flexural strength was 12~15% of its compressive strength, the general trend of flexural to compressive strength ratio in normal concrete was maintained. Even though its elastic modulus was decreased by adding the admixture, the study results showed that the concrete can be used for construction since all of the test results exceeded the code requirements.

• Korean Journal of Applied Biomechanics
• /
• v.16 no.1
• /
• pp.101-108
• /
• 2006

The purpose of this study was to compare GRF characteristics during walking wearing jogging and roller shoes. Twelve male middle school students (age: $15.0{\pm}0.0\;yrs$, height: $173.6{\pm}5.0\;cm$, weight: $587.6{\pm}89.3\;N$) who have no known musculoskeletal disorders were recruited as the subjects. Kinematic data from six S-VHS camcorders(Panasonic AG456, 60 fields/s) and GRF data from two force platform; (AMII OR6-5) were collected while subjects walked wearing roller and jogging shoes in random order at a speed of 1.1 m/s. An event sync unit with a bright LED light was used to synchronize the video and GRF recordings. GRF data were filtered using a 20 Hz low pass Butterworth. digital filter and further normalized to the subject's body weight. For each trial being analyzed, five critical instants and four phases were identified from the recording. Temporal parameters, GRFs, displacement of center of pressure (DCP), and loading and decay rates were determined for each trial. For each dependent variable, paired t-test was performed to test if significant difference existed between shoe conditions (p <.05). Vertical GRFs at heel contact increased and braking forces at the end of initial double limb stance reduced significantly when going from jogging shoe to roller shoe condition. Robbins and Waked (1997) reported that balance and vertical GRF are closely related It seems that the ankle and knee joints are locked in an awkward fashion at the heel contact to compensate for the imbalance. The DCP in the antero-posterior direction for the roller shoe condition was significantly less than the corresponding value for the jogging shoe condition. Because the subjects tried to keep their upper body weight in front of the hip to prevent falling backward, the DCP for the roller shoe condition was restricted The results indicate that walking with roller shoes had little effect on temporal parameters, and loading and decay rates. It seems that there are differences in GRF characteristics between roller shoe and jogging shoe conditions. The differences in GRF pattern may be caused primarily by the altered position of ankle, knee, and center of mass throughout the walking cycle. Future studies should examine muscle activation patterns and joint kinematics during walking with roller shoes.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.19 no.2
• /
• pp.283-299
• /
• 2017

The leakage of tunnel causes the long-term durability of the structures such as concrete lining to deteriorate. The cause of durability degradation can be various substances contained in groundwater such as chloride, sulphate, water, and gas. In this study, a series of test were carried out to determine the watertightness performance and the resistance to salt water of the spray-applied membrane used as non-structural rock support or as a waterproof material for tunnels. As a result, it was found that the penetration of water could occur in a specimen, and the reason was that the internal pores generated by the mixing of the liquid polymer and the powder material and the internal pores were connected by the water pressure. The tensile strength of the test specimens immersed in distilled water and saline water was found to be reduced to less than half of the tensile strength in normal condition. In addition, The elongation was measured to be higher in distilled water than in salt water. However, this result will require further investigation.

• Korean Journal of Materials Research
• /
• v.8 no.10
• /
• pp.961-968
• /
• 1998

In order to investigate the effects of substrate bias voltage on the formation of$ZnS-SiO_2$ protective film in phase change optical disk by R.F. magnetron sputtering method, thin dielectric film was formed on Si wafer and Corning glass by using ZnS(80mol%)-$SiO_2$(20mol%)t arget under argon gas. In this study, the Taguchi experimental method was applied in order to obtain optimum conditions with reduced number of experiments and to control numerous variables effectively. At the same time this method can assure the reproducibility of experiments. Optimum conditions for film formation obtained by above method were target RF power of 200 W. substrate RF power of 20 W, Ar pressure of 5 mTorr. sputtering time of 20 min.. respectively. The phase of specimen was determined by using XRD and TEM. The compositional analysis of specimen was performed by XPS test. In order to measure the thermal resistivity of deposited specimen, annealing test was carried out at $300^{\circ}C$ and $600^{\circ}C$. For the account of void fraction in thin film, the Bruggeman EMA(Effective Medium Approximation) method was applied using the optical data obtained by Spectroscopic Ellipsometry. According to the results of this work, the existence of strong interaction between bias voltage and sputtering time was confirmed for refractive index value. According to XRD and TEM analysis of specimen, the film structure formed in bias voltage resulted in more refined structures than that formed without bias voltage. But excess bias voltage resulted in grain growth in thin film. It was confirmed that the application of optimum bias voltage increased film density by reduction of void fraction of about 3.7%.

• Korean Journal of Medicinal Crop Science
• /
• v.16 no.4
• /
• pp.255-260
• /
• 2008

This study was performed to investigate the enhancement of UV-protection activities and skin-whitening effects from Angelica gigas Nakai extracts on ultra high pressure extraction process. Extraction at $60^{\circ}C$ treated by ultra high pressure for 15 minute and associated with ultrasofication (HPE15) was showed more than double yield, compare conventional extraction, as 12.24% (w/w) from A. gigas. Extracts of HPE15 reduced expression of MMP-1 on UV-irradiated CCD-986sk cells as 122.2% and revealed high inhibitory potency on tyrosinase as 69.4% by adding samples. Extracts of HPE15 from A. gigas showed strong inhibition effect on melanin production test by Clone M-3 cells as 82.4% by adding extracts. From the preliminary observations, we considered that the extracts from A. gigas could be potent natural materials for skin-whitening agent, and could be used as a potential anti-aging agent for the photo-damaged skin.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.43 no.10
• /
• pp.1579-1587
• /
• 2014

This study aimed to determine the quality characteristics of fermented wine using Nuruk according to the type of aging container (jar or stainless container) and aging time. Alcohol analysis was initiated at 40.4~39.3%, and alcohol contents in the jar and stainless container decreased as aging time increased. Volatile acid content slightly increased in the reduced pressure (RP) jar and stainless container and showed a different result in the atmospheric pressure (AP) container. Amount of acetic acid did not change either in the jar or stainless container as aging time increased. In the case of 2-thiobarbituric acid (TBA), RP was lower than AP after distillation, and TBA value did not change much either in the jar or stainless container. In the case of fusel alcohol by aging time, n-propanol content did not increase either in the jar or stainless container as aging time increased. Iso-butanol content was reduced in the jar but did not change in the stainless container. In the AP container, more aromatic components were measured on the 180th day of aging time than after distillation. High boiling point aromatic components increased in particular. In the stainless container, more aromatic components were generated on the 180th day of aging, but their amount was relatively lower than in the jar. In the jar aging sensory test, the sensory score at RP 50 cmHg was highest on the 180th day of aging. In the case of AP $80^{\circ}C$ liquor, sensory score on the 180th day was the most improved.

• Korean Chemical Engineering Research
• /
• v.51 no.2
• /
• pp.267-271
• /
• 2013

Test bed studies with highly efficient amine $CO_2$ solvent (KoSol-4) developed by KEPCO research institute were performed. For the first time in Korea, evaluation of post-combustion $CO_2$ capture technology to capture 2 ton $CO_2$/day from a slipstream of the flue gas from a coal-fired power station was performed. Also the analysis of solvent regeneration energy was conducted to suggest the reliable performance data of the KoSol-4 solvent. For this purpose, we have tested 5 campaigns changing the operating conditions of the solvent flow rate and the stripper pressure. The overall results of these campaigns showed that the $CO_2$ removal rate met the technical guideline ($CO_2$ removal rate: 90%) suggested by IEA-GHG and that the regeneration energy of the KoSol-4 showed about 3.0~3.2 GJ/$tCO_2$ which was, compared to that of the commercial solvent MEA (Monoethanolamine), about 25% reduction of regeneration energy. Based on these results, we could confirm the good performance of the KoSol-4 solvent and the $CO_2$ capture process developed by KEPCO research institute. And also it was expected that the cost of $CO_2$ avoided could be reduced drastically if the KoSol-4 is applied to the commercial scale $CO_2$ capture plant.

• Journal of the Korean Vacuum Society
• /
• v.5 no.4
• /
• pp.371-376
• /
• 1996

Au films with a thickness around 1600 $\AA$ were deposited onto glass at room temperature by ion beam sputtering with a 5 cm cold-hollow ion gun at pressure $1\times 10^{-6}-1\times 10^{-5}$ Torr. Irradiation of the Au deposited samples was carried out at pressure of $7\times 10^{-6}$ Torr. For the sputter depositions, $Ar^+$ ion energy was 1 keV, and the current density at the substrate surface was 15 $\mu$A/$\textrm{cm}^2$. Effects of 1 keV $Ar^+$ ion dose($I_d$) between $1\times 10^{16}\; and\;2\times 10^{17}\;Ar^+\textrm{cm}^{-2}$on properties such as crystallinity, surface roughness and adhesion, etc. of the films have been investigated. The Au films sputtered by $Ar^+$ ion beam had only (111) plane and the X-ray intensity of the films decreased with increase of $I_d$. The thickness of Au films reduced with Id. $R_{ms}$ surface roughness of the films increased from 16 $\AA$ at as-deposited to 1118 $\AA$ at ion dose= $2\times 10^{17}\;Ar^+\textrm{cm}^{-2}$. Adhesion of Au film on sputtered at $I_d$= $2\times 10^{17}\;Ar^+\textrm{cm}^{-2}$ was 9 times greater than that of Au film with untreated, as determined by a scratch test.