• Proceedings of the KSR Conference
• /
• 한국철도학회 1998년도 추계학술대회 논문집
• /
• pp.30-38
• /
• 1998

Nowadays, the environmental vibration criteria has been severely restricted from the viewpoint of recipient. The vibration created by urban transit systems can be an important source of community discontent, and can have influence on high technology equipments. This has led to a desire of transit system operators to reduce vibration and to minimize community exposure to vibration. Recent research in this area has significantly increased for transit system engineers to reduce vibration. Unlike other material, soil has a complicated characteristic and it is very difficult to prevent vibration from transmitting. Generally, the trench can use to breaking propagation of vibration on passing way but needs much too maintenance. Therefore, the filled materials for trench had successfully developed and the characteristic test for the filled material had conducted during this term. Finally, we had executed analyses of real characteristic through the propagation test of ground vibration.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 한국소음진동공학회 2004년도 춘계학술대회논문집
• /
• pp.468-473
• /
• 2004

The objective of this paper is to analyze the characteristics of wave transmission through various junctions in coupled beams. The in-plane vibration as veil as the out-of-plane vibration are generated due to the wave conversion at the junctions in the coupled beams. The out-of-plane vibration is associated with propagation of out-of-plane waves (flexural waves). The in-plane vibration is associated with propagation of in-plane waves (longitudinal and torsional waves). In order to effectively reduce vibration and structure-borne noise, it is necessary to understand the characteristics of wave conversion at various junctions in the coupled structures. The numerical results in this paper have showed the characteristics of wave transmission through various junctions in coupled beams. Those could be helpful to designer to develop the idea to reduce vibration and structure-borne noise.

• Journal of the Korean Society for Precision Engineering
• /
• 제29권6호
• /
• pp.664-670
• /
• 2012

In this work, vibration characteristics of a flue gas cooler(FGC) for a heavy oil upgrading are experimentally analyzed and an effective method is proposed to reduce the vibration level. Firstly, the vibration under the operation condition of the FGC is measured and analyzed to identify the generation phenomena of vibration. And the displacement of the outer wall of the FGC is also analyzed to identify dominant frequencies of vibration. Secondly, an effective design to reduce the vibration is suggested by using the modal analysis. Consequently an improved design of the FGC gas cooler, which has lower vibration level, is obtained and then verified though the analysis and test.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.1360-1365
• /
• 2007

A linear compressor used in a refrigerator has higher energy efficiency than other compressors. On the other hand, its vibration level has still been much severe. Changing the characteristics of connecting parts may reduce the vibration level of linear compressor. The piston, body and shell are assumed to be rigid. These rigid bodies are connected by coil springs and flexible loop pipe. This paper derived the mathematical model by combining the equation of motion of rigid parts and flexible parts. The variation of vibration level according to the change of connecting parts was investigated.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• 제7권3호
• /
• pp.29-36
• /
• 1998

In recent year, as the demand about low vibration and noise vehicle is increased constantly. automobile companies try to a lot of things to achieve this demand. Gear rattle vibration become an emergency problem to be cured at idling. There are two kinds method to reduce idle gear rattle vibration One is optimization of clutch damper design parameters(stiffness, hysteresis torque, preload, length of lst stage) the other is system parameters modification(inertia, drag torque, backlash, etc) But these methods are impossible to estimate influence rate of each gearpair on the idle gear rattle vibration. In this study, 14degrees of freedom nonlinear model is developed to analyze influnce rate of each gearpair on the idle gear rattle vibration and the counterplan to reduce the gear noise is suggeted through the shift system modification.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 한국소음진동공학회 2004년도 춘계학술대회논문집
• /
• pp.975-978
• /
• 2004

There was transient vibration on the piping system from #4 heater to the deaerator in a power plant. We found it was resulted from resonance between the natural vibration of the piping system and vibration induced by flow of feedwater. We verified it would reduce vibration by increasing stiffness of the piping system. Therefore we concluded that it would be generally better to increase stiffness of the piping system to reduce vibration amplitude of 10Hz low for big sized piping systems.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 한국소음진동공학회 2013년도 춘계학술대회 논문집
• /
• pp.816-821
• /
• 2013

This case study presents a practical method to reduce resonant vibration of generator-motor set. The generator is driven at 1800rpm by induction integral motor. The vibration is below alarm limits, but the dominant frequency of vibration is sub-synchronous and close to that of bearing fault signal in spite of new bearings. To find an mechanism of abnormal vibration, ODS and Modal analysis is carried out. The measured modal characteristics were compared with those of FE Analysis. The ODS mode at rated speed is consistent with system natural frequency mode that is excited by bearings. To reduce vibration level, the isolation mount at system base is changed with new rubber mount for lower natural frequency.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 한국소음진동공학회 2004년도 춘계학술대회논문집
• /
• pp.764-769
• /
• 2004

The DC Motor in a vehicle may cause noise and vibration because of high speed revolution, which can make a driver feel uncomfortable. There have been various studies attempting to solve these problems, focusing mostly on the causes of and ways to reduce noise and vibration. It is suggested that the noise in a DC Motor may be primarily due to interaction between a brush and a commutator. Brush noise, the most common noise in a DC Motor, results from a brush bounced from the surface of the commutator, fluctuation of the friction between the brush and the commutator, and the impact on the brush when passing over slots of the commutator. Based on the noise test, one of the most important design parameters was shown to be the roundness of the commutator. As the DC motor is used, the roundness of the commutator gets bigger with subsequent increase of the level of brush noise and vibration. There must be a threshold in order to prevent the brush noise from getting worse. Using the method of CAE is more efficient than the real test for purposes of looking for various design parameters to maintain the roundness of the commutator. In this study, the design process to reduce the brush noise is presented with the use of a computer model. The design parameters to reduce the brush noise and vibration are proposed by using FEM. The design parameters are used to reduce the noise and vibration of a DC motor and it is verified with the test results on a fan DC motor in a vehicle. This method may be applicable to various DC motors.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 한국소음진동공학회 2003년도 춘계학술대회논문집
• /
• pp.944-949
• /
• 2003

A High-speed cutter, a kind of electric tool is studied to reduce its vibration and noise. The experimental modal analysis, the operational deflection shapes(ODS) and the time domain analysis(TDA) are used in the SMS software to analyze the vibration signals from an operating high-speed cutters under steady state operating condition. The second mode and fifth m,)do of the base plate coincide with the driving frequencies of the motor, And the vibration of the wheel cover is caused by the gap between the main wheel cover and the sub wheel cover. The structural modification for the base plate was done to reduce the vibration. The effect of modification is verified through the test.

• Transactions of the Korean Society of Automotive Engineers
• /
• 제18권2호
• /
• pp.114-121
• /
• 2010

As a vehicle speed increases, more vibration energy is transmitted from chassis to a driver. Current isolation system for the driver's seat by damping control can reduce the transmitted vibration energy near resonance area. But in higher frequency region than natural frequency multiplied by $\sqrt{2}$, the vibration energy transmitted to the driver has a tendency to be increased. Therefore, the method by natural frequency reduction of the system is preferred to increase the effectiveness of the anti-vibration. However, the natural frequency could not be freely reduced due to the nature of the isolation system structure. A new passive suspension system to reduce the natural frequency is proposed. The theoretical analysis and experimental results show better vibration attenuation compared with the current isolation system.