• Journal of Power Electronics
• /
• v.16 no.6
• /
• pp.2035-2044
• /
• 2016

In order to match the voltages between high voltage battery stacks and low voltage super-capacitors with a high conversion efficiency in hybrid energy sources electric vehicles (HESEVs), a high ratio bidirectional DC-DC converter with a synchronous rectification H-Bridge is proposed in this paper. The principles of high ratio step-down and step-up operations are analyzed. In terms of the bidirectional characteristic of the H-Bridge, the bidirectional synchronous rectification (SR) operation is presented without any extra hardware. Then the SR power switches can achieve zero voltage switching (ZVS) turn-on and turn-off during dead time, and the power conversion efficiency is improved compared to that of the diode rectification (DR) operation, as well as the utilization of power switches. Experimental results show that the proposed converter can operate bidirectionally in the wide ratio range of 3~10, when the low voltage continuously varies between 15V and 50V. The maximum efficiencies are 94.1% in the Buck mode, and 93.6% in the Boost mode. In addition, the corresponding largest efficiency variations between SR and DR operations are 4.8% and 3.4%. This converter is suitable for use as a power interface between the battery stacks and super-capacitors in HESEVs.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.395-399
• /
• 1996

The Clamp Mode(CM) Forward Zero Voltage Switching Multi Resonant Converter(ZVS-MRC) with self-driven synchronous rectifier in studied. The loss at the synchronous rectification stage of the converter is analyzed using MOSFET linear model and is compared with the loss at the conventional schottky diode rectification stage of the converter. From the results of the analysis, it is known that the use of MOSFETs as a synchronous rectifier reduces the loss at the rectification stage over the whole load range comparing the use of schottky diodes as a conventional rectifier in the converter. In order to verify the validity of the analysis, we have built a 33W(3.3V/10A) CM Forward ZVS-MRC with self-driven synchronous rectifier, in which switching frequency is 1MHz, and tested. From the experimental results, it is known that the synchronous rectification achieved about 1W improvement in the loss at the rectification stage and about 3% in the efficiency at the converter as compared with the conventional schottky diode rectification.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.1
• /
• pp.44-57
• /
• 2016

Rectification is used as a preprocessing to reduce the computation complexity of disparity estimation. However, rectification also requires a complex computation. To minimize the computing complexity, rectification using a lookup-table (R-LUT) has been introduced. However, since, the R-LUT consumes large amount of memory, rectification with compressed LUT (R-CLUT) has been introduced. However, the more we reduce the memory consumption, the more we need decoding overhead. Therefore, we need to attain an acceptable trade-off between the size of LUT and decoding overhead. In this paper, we present such a trade-off by adaptively combining simple coding methods, such as differential coding, modified run-length coding (MRLE), and Huffman coding. Differential coding is applied to transform coordinate data into a differential form in order to further improve the coding efficiency along with Huffman coding for better stability and MRLE for better performance. Our experimental results verified that our coding scheme yields high performance with maintaining robustness. Our method showed about ranging from 1 % to 16 % lower average inverse of compression ratio than the existing methods. Moreover, we maintained low latency with tolerable hardware overhead for real-time implementation.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.53 no.5
• /
• pp.351-357
• /
• 2004

In this paper, we present an analytical method that provides fast and efficient evaluation of the conversion efficiency for switching power supplies. In the proposed method, the conduction losses are evaluated by calculating the effective values of the ideal current waveform first and incorporating them into an exact equivalent circuit model of the switching power supply that includes all the parasitic resistances of the circuit components. While the winding losses and core losses are accurately accounted for the magnetic components, the skin and proximity effects are assumed to be negligible in order to simplify the analysis. The validity and accuracy of the proposed method are verified with experiments on a prototype active-clamped forward converter with synchronous rectification. An excellent correlation between the experiments and theories are obtained for the input voltages of 36-75 V with 4-6 MOSFETs employed for the synchronous rectification.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.1
• /
• pp.413-419
• /
• 2011

Diagnosis X-ray equipment localized at 1950's but it is developed suddenly at 1960's with demand together. Manufacture of Diagnostic X-ray equipment is controled by the KS regulation and the Ministry of Health and Welfare because of hazardous element etc. exposure by radiation. Most of diagnostic X-ray equipment ware single phase and three phase full-wave rectification but from 1980's it transforms it was exchanged in inverter type X-ray equipment. Inverter type X-ray equipment produces approximately 50~80% more average photon intensity then single phase full-wave rectification and the accuracy is high. But from a clinic it dose not use because expensive therefor the efficiency improvement of single phase full-wave rectification is necessary. We produced single phase full-wave rectification X-ray equipment control unit, high tension transformer, filament heating transformer, rectification circuit, high tension cable and others and evaluated efficiency, in result which is excellent compare with Rule of Safety Management and KS regulation.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.7
• /
• pp.534-538
• /
• 2010

X-ray systems for medical treatment use noninvasive procedures. Being capable of locally inspecting the inside of the body, X-ray systems are routinely used for basic diagnosis. X-ray systems to be used for medical purposes were originally made with a gas filled tube inside an induction coil in the initial stages of development but with this approach it becomes difficult to take a satisfactory picture through thick body sections, non invasively. However continued development made it possible to take non-invasive pictures of breasts, blood vessels and other body parts through thick body sections. Recently, high-voltage X-ray generators of more compact size, increased generation efficiency, and sophisticated output control have become possible. All of these features are made possible by the use of a high-frequency output from an inverter and a fast switching semiconductor device. In this paper, we describe a new X-ray generator operating with a resonant inverter in order to reduce switching loss and high frequency noise. In addition, in order to identify the differences amongst types of rectification, we have compared output and the quality of X-ray pictures obtained with full-wave rectification and dual-voltage rectification methods.

• Proceedings of the KIEE Conference
• /
• 1998.07f
• /
• pp.1973-1976
• /
• 1998

Recently, new trend in telecommunication device is to apply low voltage, about 3.3V-1.5V. However, it is undesirable in view of high efficiency and power desity which is the most important requirement in the distributed power system. Rectification loss in the output stage, in on-board converter for distributed power system are constrained to obtain high efficience at low output voltage power suppies. This paper explains the basic operational principles of three kinds of ZVS DC/DC converters with self-driven synchronous rectifier. The three topologies are analyzed by simulation and exprimentation, and the characteristics comparisons of high efficience converter are carried out in view of the minimized rectification losses in the out stage.

• Journal of Power Electronics
• /
• v.6 no.3
• /
• pp.187-194
• /
• 2006

A new asymmetrical pulse width modulation (PWM) half bridge converter with improved ZVS performance is proposed. The ZVS operation of the proposed converter can be maintained from no load to full load conditions since the magnetizing current of the transformer contributes to the ZVS operation at light loads without considerable conduction loss of the transformer and switch. Synchronous rectification is employed to reduce the rectification loss. Operational principles, large signal modeling, ZVS analysis and design equations are presented. Experimental results demonstrate that the proposed converter can achieve a large ZVS range and significant improvement in efficiency for a 100W (5V, 20A) prototype converter.

• Proceedings of the KIPE Conference
• /
• 2017.07a
• /
• pp.40-41
• /
• 2017

New adaptive SR (synchronous rectification) control method is proposed offering high efficiency in entire load conditions for resonant converters, in this paper. Unlike the conventional SR control method where turn-on time of the MOSFETs is varied depending on load conditions due to the stray inductance induced by a lead frame of MOSFET or PCB patterns, the proposed method automatically maintains a time interval between turn-off instance of a MOSFET and zero current instance of a body diode of the MOSFET as a predetermined time, in each switching cycle. Therefore, optimized turn-on time of the MOSFET can be achieved regardless of the leakage inductance. In this paper, the operational principle of proposed control method has been discussed. It has been tested on LLC resonant converter with 240 W to verify the proposed control method.

• Journal of Ocean Engineering and Technology
• /
• v.2 no.2
• /
• pp.130-137
• /
• 1988

This thesis introduced that character of a treatment technique for a mading synthetic resin Hifiow-Ring. The material system of packings make an experiment air$NH_{3}$/air$H_{2}SO_{4}$, $SO_{2}$-air/NaOH, $NH_{3}$-air/$/H_{2}SO_{4}$ under general conditions. Lattices packing compared with conventional packings was proved low pressure loss and high separation efficiency for high loading per trans unit. And an inflow materal tested for absorption and rectification, it made an experiment under a range regular temperature, low energy and small amount of money. That made possible in simple equation, volume material tranfer coefficient$\beta_{L}$ . a by absorption or $\beta_{V}$ .a calculated in all range loading. The peculiarity pressure loss $\Delta\;P/NUT_{ov}$ for Hiflow-ring contributed to a fall cost of energy, a grade number of a vacuum rectification and absorption calculation.