• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.3A
• /
• pp.201-209
• /
• 2010

Generally, PSC girder bridge uses total gross cross section to resist applied loads unlike reinforced concrete member. Also, it is used as short and middle span (less than 30 m) bridges due to advantages such as ease of design and construction, reduction of cost, and convenience of maintenance. But, due to recent increased public interests for environmental friendly and appearance appealing bridges all over the world, the demands for longer span bridges have been continuously increasing. This trend is shown not only in ordinary long span bridge types such as cable supported bridges but also in PSC girder bridges. In order to meet the increasing demands for new type of long span bridges, PSC hollow box girder with H-type steel as compression reinforcements is developed for bridge with a single span of more than 50 m. The developed PSC girder applies compressive prestressing at H-type compression reinforcements using unbonded PS tendon. The purpose of compressive prestressing is to recover plastic displacement of PSC girder after long term service by releasing the prestressing. The static test composed of 4 different stages in 3-point bending test is performed to verify safety of the bridge. First stage loading is applied until tensile cracks form. Then in second stage, the load is removed and the girder is unloaded. In third stage, after removal of loading, recovery of remaining plastic deformation is verified as the compressive prestressing is removed at H-type reinforcements. Then, in fourth stage, loading is continued until the girder fails. The experimental results showed that the first crack occurs at 1,615 kN with a corresponding displacement of 187.0 mm. The introduction of the additional compressive stress in the lower part of the girder from the removal of unbonded compressive prestressing of the H-type steel showed a capacity improvement of about 60% (7.7 mm) recovery of the residual deformation (18.7 mm) that occurred from load increase. By using prestressed H-type steel as compression reinforcements in the upper part of cross section, repair and rehabilitation of PSC girders are relatively easy, and the cost of maintenance is expected to decrease.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.5A
• /
• pp.565-575
• /
• 2009

In recent years, there have been numerous explosion-related accidents due to military and terrorist activities. Such incidents caused not only damages to structures but also human casualties, especially in urban areas. To protect structures and save human lives against explosion accidents, better understanding of the explosion effect on structures is needed. In an explosion, the blast load is applied to concrete structures as an impulsive load of extremely short duration with very high pressure and heat. Generally, concrete is known to have a relatively high blast resistance compared to other construction materials. However, normal strength concrete structures require higher strength to improve their resistance against impact and blast loads. Therefore, a new material with high-energy absorption capacity and high resistance to damage is needed for blast resistance design. Recently, Ultra High Strength Concrete(UHSC) and Reactive Powder Concrete(RPC) have been actively developed to significantly improve concrete strength. UHSC and RPC, can improve concrete strength, reduce member size and weight, and improve workability. High strength concrete are used to improve earthquake resistance and increase height and bridge span. Also, UHSC and RPC, can be implemented for blast resistance design of infrastructure susceptible to terror or impact such as 9.11 terror attack. Therefore, in this study, the blast tests are performed to investigate the behavior of UHSC and RPC slabs under blast loading. Blast wave characteristics including incident and reflected pressures as well as maximum and residual displacements and strains in steel and concrete surface are measured. Also, blast damages and failure modes were recorded for each specimen. From these tests, UHSC and RPC have shown to better blast explosions resistance compare to normal strength concrete.

• Asia Marketing Journal
• /
• v.13 no.4
• /
• pp.227-251
• /
• 2012

This study analyzed Woori Investment and Securities' industry-leading marketing from both a brand management and a marketing decision-making perspective. By executing a different marketing strategy from its competitors, Woori Investment and Securities recognized recent changes in the asset management and investment markets as an open opportunity, and quickly responded to the market changes. First, the company launched the octo brand as a multi-account product, two years before its competitors offered their own products. In particular, it created a differentiated brand image, using the blue octopus character, which became familiar to the general financial community, and was consistently employed as part of an integrated marketing communications strategy. Second, it executed a brand expansion strategy by sub-branding octo in a variety of new financial products, responding to rapid changes in the domestic financial and asset management markets. Through this strategic evolution, the octo brand became a successful wealth management brand and representative of Woori Investment & Securities. Third, it has converged market research, demand and trend analysis, and customer needs acquired through various customer contact channels into a marketing perspective. Thus, marketing has participated in the product development stage, a rarity in the finance industry. Woori Investment and Securities has a leading marketing system. The heart of the successful product creation lies in a collaboration of their customer bases among the finance companies in the Woori Financial Group. The present study suggested a corresponding strategy for octo brand, which is expected to enter into the maturity stage of its product life cycle. In addition, this study found a need to modify the current positioning strategy in order to position and preserve sustainability in the increasingly competitive asset management market. It also suggested the need for an offensive strategy to counter the number one M/S company, and address the issue of cannibalism in the Woori Financial Group.

• Korean Journal of Remote Sensing
• /
• v.39 no.6_2
• /
• pp.1591-1604
• /
• 2023

In ocean color remote sensing, atmospheric correction is a vital process for ensuring the accuracy and reliability of ocean color products. Furthermore, in recent years, the remote sensing community has intensified its requirements for understanding errors in satellite data. Accordingly, research is currently addressing errors in remote sensing reflectance (R_rs) resulting from inaccuracies in meteorological variables (total ozone, pressure, wind field, and total precipitable water) used as auxiliary data for atmospheric correction. However, there has been no investigation into the error in R_rs caused by the variability of the water vapor profile, despite it being a recognized error source. In this study, we used the Second Simulation of a Satellite Signal Vector version 2.1 simulation to compute errors in water vapor transmittance arising from variations in the water vapor profile within the GOCI-II observation area. Subsequently, we conducted an analysis of the associated errors in ocean color products. The observed water vapor profile not only exhibited a complex shape but also showed significant variations near the surface, leading to differences of up to 0.007 compared to the US standard 62 water vapor profile used in the GOCI-II atmospheric correction. The resulting variation in water vapor transmittance led to a difference in aerosol reflectance estimation, consequently introducing errors in R_rs across all GOCI-II bands. However, the error of R_rs in the 412-555 nm due to the difference in the water vapor profile band was found to be below 2%, which is lower than the required accuracy. Also, similar errors were shown in other ocean color products such as chlorophyll-a concentration, colored dissolved organic matter, and total suspended matter concentration. The results of this study indicate that the variability in water vapor profiles has minimal impact on the accuracy of atmospheric correction and ocean color products. Therefore, improving the accuracy of the input data related to the water vapor column concentration is even more critical for enhancing the accuracy of ocean color products in terms of water vapor absorption correction.

• Journal of Korea Society of Industrial Information Systems
• /
• v.28 no.6
• /
• pp.53-62
• /
• 2023

This paper has suggested the necessity of introducing training contents using XR(Extended reality) technology as a way to lower the high rate of nursing accidents among unskilled technical personnel in domestic shipbuilding industry, focusing on cable pulling using winch. The occurrence rate of nursing accidents in the domestic shipbuilding industry was almost double(197.4%) (2017~2020) when compared with other manufacturing industries. In particular, it is worth noting that more than 31.8% of nursing accidents in the shipbuilding industry occurred among workers whose job experience is no more than 6 months. Most of new workers are seen to have hard time due to several factors such as lack of work information, inexperience, and unfamiliarity with the working environments. This indicates that it is essential to incorporate more effective training method that could help new workers become familiar with technical skills as well as working environments in a short period of time. Currently, education/training at the domestic shipyard is biased toward technical skills such as welding, painting, machine installation, and electrical installation. Contrary, even more important training required to get new workers used to the working environment has remained at a superficial level such as explaining ship building processes using 2D drawings. This may be the reason why it is inevitable to repeat similar training at OJT (On-the-Job Training) even at the leading domestic companies. Domestic shipbuilding industries have been attracting a lot of new workers thanks to recent economic recovery, which is very likely to increase the occurrence of disasters. In this paper, the introduction of training using XR technology was proposed, and as a specific example, the process of pulling cables using winches on ships was implemented as XR-based training content by using Unity. Using the developed content, it demonstrated that new workers can experience the actual work process in advance through simulation in a virtual space, thereby becoming more effective training content that can help new workers become familiar with the work environment.

• Journal of Korea Water Resources Association
• /
• v.56 no.12
• /
• pp.919-928
• /
• 2023

Rainfall characteristics in Korea are concentrated during the summer flood season. In particular, when a large amount of turbid water flows into the dam due to the increasing trend of concentrated rainfall due to abnormal rainfall and abnormal weather conditions, prolonged turbid water phenomenon occurs due to the overturning phenomenon. Much research is being conducted on turbid water prediction to solve these problems. To predict turbid water, turbid water data from the upstream inflow is required, but spatial and temporal data resolution is currently insufficient. To improve temporal resolution, the development of the Turbidity-SS conversion equation is necessary, and to improve spatial resolution, multi-item water quality measurement instrument (YSI), Laser In-Situ Scattering and Transmissometry (LISST), and hyperspectral sensors are needed. Sensor-based measurement can improve the spatial resolution of turbid water by measuring line and surface unit data. In addition, in the case of LISST-200X, it is possible to collect data on particle size, etc., so it can be used in the Turbidity-SS conversion equation for fraction (Clay: Silt: Sand). In addition, among recent remote sensing methods, the spatial distribution of turbid water can be presented when using UAVs with higher spatial and temporal resolutions than other payloads and hyperspectral sensors with high spectral and radiometric resolutions. Therefore, in this study, the Turbidity-SS conversion equation was calculated according to the fraction through laboratory analysis using LISST-200X and YSI-EXO, and sensor-based field measurements including UAV (Matrice 600) and hyperspectral sensor (microHSI 410 SHARK) were used. Through this, the spatial distribution of turbidity and suspended sediment concentration, and the turbidity calculated using the Turbidity-SS conversion equation based on the measured suspended sediment concentration, was presented. Through this, we attempted to review the applicability of the Turbidity-SS conversion equation and understand the current status of turbid water occurrence.

• Asia-Pacific Journal of Business Venturing and Entrepreneurship
• /
• v.18 no.1
• /
• pp.203-223
• /
• 2023

Recently, the platform industry is rapidly growing in the global market, and competition is intensifying at the same time. Therefore, in order for domestic platform companies to have global competitiveness in the platform market, it is necessary to study the platform business ecosystem and success factors. However, most of the recent platform-related studies have been theoretical studies on the characteristics of platform business status analysis, platform economy, and indirect network externalities of platforms. Therefore, this study comprehensively analyzed the success factors of Silicon Valley's business ecosystem proposed in previous studies, and at the same time analyzed the success factors extracted from stakeholders in the actual Silicon Valley platform business ecosystem. And based on these factors, an IPA analysis was conducted as a way to propose a success plan to stakeholders in the platform business ecosystem. As a result of the analysis, among the success factors collected through previous studies, manpower, capital, and challenge culture were identified as factors that are relatively well maintained in both importance and satisfaction in Silicon Valley. In the end, it can be seen that the creation of an environment and culture in which Silicon Valley can use it to challenge itself based on excellent human resources and abundant capital contributes the most to the success of Silicon Valley's platform business. On the other hand, although it is of high importance to Silicon Valley's platform corporate ecosystem, the factors that show relatively low satisfaction among stakeholders are 'learning and benchmarking among active companies' and 'strong ties and cooperation between members', and it is analyzed that interest and effort are needed to strengthen these factors in the future. Finally, the systems and policies necessary for market autonomous competition, 'business support service industry', 'name value', and 'spin-off start-up' were important factors in literature research, but the importance and satisfaction of these factors were lowered due to changes in the times and environment. This study has academic implications in that it comprehensively analyzes the success factors of Silicon Valley's business ecosystem proposed in previous studies, and at the same time analyzes the success factors extracted from stakeholders in the actual Silicon Valley platform business ecosystem. In addition, there is another academic implications that importance and satisfaction were simultaneously examined through IPA analysis based on these various extracted factors. As for academic implications, it is meaningful in that it contributed to the formation of the domestic platform ecosystem by providing the government and companies with concrete information on the success factors of the platform business ecosystem and the theoretical grounds for the growth of domestic platform businesses.

• Asia-Pacific Journal of Business Venturing and Entrepreneurship
• /
• v.18 no.3
• /
• pp.157-172
• /
• 2023

The recent Fourth Industrial Revolution is accelerating changes due to digital transformation. According to this trend, the existing start-up paradigm is changing, and new business models based on new technologies and creative ideas are emerging. In addition, the diversity of mentoring relationships and environments such as online mentoring, reverse mentoring, group mentoring, and multiple mentoring is also increasing. However, most mentors in their 50s and 60s, who are mainly active in the start-up field, have been able to help mentees a lot based on their own experience and expertise, but they are having difficulty responding to the changing environment due to a lack of understanding and experience of new technologies and environments. To cope with these changes well, mentors must constantly study, acquire and apply the latest technologies to improve their understanding of new technologies and the environment. In addition, it is necessary to have an understanding and respect for the diversity of mentoring relationships and environments, and to maximize the effectiveness of mentoring by actively utilizing them. Therefore, mentors should recognize that they directly affect the growth and development of mentees, constantly acquire new knowledge and skills to maintain and develop expertise, and actively deliver their knowledge and experiences to mentees. Therefore, in this study, was tried to empirically analyze the relationship between mentoring's influence on mentor's job satisfaction through mentor's personal learning and self-efficacy. The results of the empirical analysis were as follows. Among the functions of mentoring, career function and role modeling were found to have a positive effect on both personal learning and self-efficacy, which are parameters, and job satisfaction, which is a dependent variable. On the other hand, psychological and social functions have a positive effect on personal learning, but they do not have an effect on self-efficacy and job satisfaction. In addition, as a result of analyzing the mediating effect, all mediating effects were confirmed for career functions, and only the mediating effect of self-efficacy was confirmed for role modeling. Through this study, mentoring is an important factor in promoting job satisfaction, personal learning and self-efficacy, and this study can be said to be academically and practically meaningful in that it confirmed personal learning and self-efficacy as factors that increase mentor's job satisfaction, and the focus of mentoring research was shifted from mentee to mentor to study the impact of mentoring on mentors.

• Asia-Pacific Journal of Business Venturing and Entrepreneurship
• /
• v.18 no.4
• /
• pp.37-50
• /
• 2023

Venture capital invests the necessary capital and supports management and technology in promising small and medium-sized venture companies in the early stages of start-up with promising technology and excellent manpower. It plays a role as a key player in the venture ecosystem that realizes profits by collecting the investment through various means after growth. Venture capital's job is to recruit various investors(LPs) to invest in small and medium-sized venture companies with growth potential through the formation of venture investment funds, and to collect investment as companies grow, distribute and reinvest. The main tasks of venture capitalists, which play the most important role in venture investment, are finding promising companies, corporate analysis and evaluation, investment screening, follow-up management, and investment recovery. Venture capital's success indicators are fund formation and return on investment, and venture capitalists are rewarded with annual salary, performance-based incentive, and promotion with work performance such as investment, exit, and fund formation. Compared to the recent rapidly growing venture investment market, investment manpower is insufficient, and venture capital is making great efforts to foster manpower and establish infrastructure and systems for long-term service, but research has been conducted mainly from a quantitative perspective. Accordingly, this study aims to empirically analyzed the impact of investment experience, delegation of authority, job fit, and peer relationships on fund formation and return on investment according to the characteristics of the venture capital industry. The results of these empirical studies suggested that future venture capital needs a job environment and manpower operation strategy so that venture capitalists with high job fit and investment experience can work for a long time.

• The Transactions of the Korea Information Processing Society
• /
• v.13 no.4
• /
• pp.189-198
• /
• 2024

Lipreading is one of the important parts of speech recognition, and several studies have been conducted to improve the performance of lipreading in lipreading systems for speech recognition. Recent studies have used method to modify the model architecture of lipreading system to improve recognition performance. Unlike previous research that improve recognition performance by modifying model architecture, we aim to improve recognition performance without any change in model architecture. In order to improve the recognition performance without modifying the model architecture, we refer to the cues used in human lipreading and set other regions such as chin and cheeks as regions of interest along with the lip region, which is the existing region of interest of lipreading systems, and compare the recognition rate of each region of interest to propose the highest performing region of interest In addition, assuming that the difference in normalization results caused by the difference in interpolation method during the process of normalizing the size of the region of interest affects the recognition performance, we interpolate the same region of interest using nearest neighbor interpolation, bilinear interpolation, and bicubic interpolation, and compare the recognition rate of each interpolation method to propose the best performing interpolation method. Each region of interest was detected by training an object detection neural network, and dynamic time warping templates were generated by normalizing each region of interest, extracting and combining features, and mapping the dimensionality reduction of the combined features into a low-dimensional space. The recognition rate was evaluated by comparing the distance between the generated dynamic time warping templates and the data mapped to the low-dimensional space. In the comparison of regions of interest, the result of the region of interest containing only the lip region showed an average recognition rate of 97.36%, which is 3.44% higher than the average recognition rate of 93.92% in the previous study, and in the comparison of interpolation methods, the bilinear interpolation method performed 97.36%, which is 14.65% higher than the nearest neighbor interpolation method and 5.55% higher than the bicubic interpolation method. The code used in this study can be found a https://github.com/haraisi2/Lipreading-Systems.