• Journal of the Optical Society of Korea
• /
• v.20 no.5
• /
• pp.623-627
• /
• 2016

A power-adjustable fully-integrated CMOS optical receiver with multi-rate clock-and-data recovery circuit is presented in standard 65-nm CMOS technology. With supply voltage scaling, key features of the optical receiver such as bandwidth, power efficiency, and optical sensitivity can be automatically optimized according to the bit rates. The prototype receiver has −23.7 dBm to −15.4 dBm of optical sensitivity for 10⁻⁹ bit error rate with constant conversion gain around all target bit rates from 1.62Gbps to 8.1 Gbps. Power efficiency is less than 9.3 pJ/bit over all operating ranges.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.16 no.3
• /
• pp.373-381
• /
• 2013

In this paper, the effects of phase noise on the radar system were analyzed in terms of 3 point of view. The impact(s) on the compressed pulse waveform, the FMICW(Frequency Modulated Interrupted Continuous Wave) radar performance and the receiver sensitivity were investigated. From the investigation, it was indicated that the phase noise over 10 kHz offset frequency makes the side lobe level of compressed pulse worse. Also it was founded that the FMICW radar performance, especially at the noise level of range profile, is related to the phase noise. Finally, the investigation showed that the phase noise at local oscillator affects the receiver sensitivity.

• Journal of Advanced Navigation Technology
• /
• v.10 no.1
• /
• pp.26-33
• /
• 2006

This paper discusses the design and fabrication of a wireless VHF receiver for use in air traffic control. The VHF receiver was designed and tested in three modules: a control module, a receiver module and a power module, all of which were integrated into a single block for final testing. The fundamental performance of the receiver, and in particular, sensitivity, the most important factor, is designed to satisfy existing commercial wireless transmitter specifications for air traffic control. The receiver displays a sensitivity of -113 dBm, which is higher performance than existing commercial products, and is suitable for use as a basic component of CNS/ATM.

• Journal of Broadcast Engineering
• /
• v.21 no.4
• /
• pp.506-514
• /
• 2016

In this study, HEVC over DVB-T2 systems with a bandwidth of 6 MHz is considered, particularly for the terrestrial 4K-UHDTV broadcasting service in the Republic of Korea. The threshold of visibility carrier-to-noise power ratio (ToV C/N) and the receiver minimum required input level (sensitivity) for satisfying the subjective picture failure (SPF) condition are measured in the laboratory. It is observed, for transmitting 26.37 Mbps data stream correctly, that ToV C/N is 18.8 dB on average, and the receiver sensitivity is varied from minimum -84.2 dBm to maximum -80.0 dBm. Based on the results, the receiver noise floor is calculated by -100 dBm on average.

• Korean Journal of Optics and Photonics
• /
• v.19 no.5
• /
• pp.343-348
• /
• 2008

This study was carried out to commercialize FTTH by developing a burst mode optical receiver for E-PON. The optical receiver was manufactured by minimizing the capacitance of a photodiode to improve sensitivity for meeting 10, 20 km OLT Rx standard of E-PON at the transmission speed of 1.25 Gb/s. When bit-error ratio is $10^{-12}$ and PRBS is $2^5-1$, sensitivity is -26 dBm, loud/soft ratio is 23 dB. Both preamble time and guard time were set to 102.4 ns (128 bit). After comparing a photodiode whose capacitance is 0.53 pF with another photodiode whose capacitance has been minimized to 0.26 pF, we could see that sensitivity improved to 0.7 dBm and so did bandwidth to 190 MHz of burst mode for the optical receiver manufactured by the photodiode whose capacitance is 0.26 pF.

• The Korean Journal of Applied Statistics
• /
• v.33 no.5
• /
• pp.541-553
• /
• 2020

The receiver operating characteristic (ROC) curve is expressed as both sensitivity and specificity; in addition, some optimal thresholds using the ROC curve are also represented with both sensitivity and specificity. In addition to the sensitivity and specificity, the expected usefulness function is considered as disease prevalence and usefulness. In particular, partial the area under the ROC curve (AUC) on a certain range should be compared when the AUCs of the crossing ROC curves have similar values. In this study, partial AUCs representing high sensitivity and specificity are proposed by using sensitivity and specificity lines, respectively. Assume various distribution functions with ROC curves that are crossing and AUCs that have the same value. We propose a method to improve the discriminant power of the classification models while comparing the partial AUCs obtained using sensitivity and specificity lines.

• Proceedings of the KIEE Conference
• /
• 2002.11c
• /
• pp.613-616
• /
• 2002

This paper has been studied an improvement of receive sensitivity for RF module of Industrial Scientific Medical(ISM) Band. In the paper, Also this paper handles receive sensitivity progress of RF module in ISM band. how to improve receive sensitivity adds to Surface Acoustic Wave(SAW) filter, Low Noise Filter(LNA), etc and insulates receiver and transmitter. And then the circuit is inspected by the effective range test of receiver and transmitter. And this Paper was designed that micro-controler controls the part of RF by software.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.16 no.2
• /
• pp.214-217
• /
• 2013

In this paper, we proposed an automatic threshold control method for radar warning receiver. Considering the noise level of the environment, this technique can effectively adjust sensitivity level of radar warning receiver and can offer more accurate radar information for aircraft pilot in noisy circumstances.

• Proceedings of the IEEK Conference
• /
• 1998.06a
• /
• pp.110-113
• /
• 1998

An analysis of the relationship between a linear amplifier chain and an analog-to-digital converter(ADC) in a digital microwave widevand receiver, with respect to sensitivity and dynamic range issues, is presented. The effects of gain, third-order intermodulation products and ADC characteristics on the performance of the receiver are illustrated and design criteria for the linear amplifier chain given a specified ADC are developed. A computer program is used to calculate theretical receiver performance based on gain and third-order intermodulation product selections. Simulated results are also presented and compared with theoretical values.

• Proceedings of the IEEK Conference
• /
• 1999.11a
• /
• pp.817-820
• /
• 1999

In this paper, we describes RF receiver module for IMT-2000 handset with 5MHz channel bandwidth. The fabricated RF receiver module consists of Low Noise Amplifier-, RF SAW filter, Down-converter, IF SAW filter, AGC and PLL Synthesizer. The NF and IIP3 of LNA is 0.8㏈, 3㏈m at 2.14㎓, conversion gain of downconverter is l0㏈, dynamic range of AGC is 80㏈, and phase noise of PLL is -100 ㏈m, at 100KHz. The receiver sensitivity is -110㏈m, adjacent channel selectivity is -48㏈m.