• 한국구조물진단유지관리공학회 논문집
• /
• 제12권3호
• /
• pp.199-207
• /
• 2008

최근 구조물이 노후화되면서 기존 구조물과 시공품질을 관리하는 비파괴검사 평가의 요구가 증가되고 있다. 콘크리트 구조물의 압축강도 추정의 중요성이 건설업계에서 또한 점차적으로 증대되고 있는 실정이고, 시공관리와 품질관리에 있어서 중요한 요소이다. 본 연구는 콘크리트의 압축강도를 비교하기 위한 비파괴 검사법 중 슈미트해머 시험과 충격반향기법을 이용하여 수행되었다. 콘크리트 압축강도와 슈미트해머에 의한 반발경도 값과 충격반향기법 실험결과와의 관계를 알아내는데 초점을 두었으며, 콘크리트의 압축강도와 반발경도 값은 밀접한 관계가 있음을 알 수 있었다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1994년도 가을 학술발표회 논문집
• /
• pp.429-434
• /
• 1994

In this study, an experiment in the field was performed to analyze the variations of rebound ratios of SFRS with silica fume after fabricating the panels and placing the plain concrete of simulting a base rock with thickness 7cm. And the experimental parameters which are the reinforcing methods(steel fiber, wire mesh), steel fiber contents(0.0%, 0.5%, 0.75%, 1.0%), silica fume contents(0.0%, 10.0%), and the three parts(lower, middle, upper part) were chosen. According to the results of the lower part in this test, the larger the fiber contents are in case of steel fiber reinforced shotcrete, the less the rebound ratios are within the range of 20~35%, compared to the wire-mesh reinforced shotcrete with silica fume content of 10%, and these results are true of the middle and upper part, respectively. In addition, the four-stage phenomena of the rebound of SFRS were estimated on the base of a series of the test results.

• 콘크리트학회논문집
• /
• 제11권4호
• /
• pp.157-167
• /
• 1999

Among several non-destructive testing methods, ultrasonic pulse velocity method and rebound index method have been widely used for the evaluation of concrete strength. However, such methods might not provide accurate estimated results since factors influencing the relationship between strength and either ultrasonic pulse velocity or rebound index are not considered. In this paper, the evaluation method of concrete strength using rod-wave velocity measured by impact-resonance method is proposed. A basic equation is obtained by the linear regression of velocity vs, strength data at specific age and then, aging factor is employed in the equation to consider the difference of the increasing rate between wave velocity and strength. Strengths predicted by the proposed equation agree well with test results. Furthermore, the combined method of rod-wave velocity and rebound index is proposed.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1999년도 가을 학술발표회 논문집
• /
• pp.285-292
• /
• 1999

The cyclic plate load test were peformed to determine the behavior of reinforced soft ground with multiple layers of geogrid. Five series of test were conducted with varying the soil profile conditions which including the ground level, type of soil, and the thickness of each soil layer. The plate load test equipment was slightly modified to apply the cyclic load. Based on the cyclic plate load test results, the bearing capacity ratio(BCR), subbase modules, shear modules, the elastic rebound ratio, and reinforcing parameters are presented.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 가을 학술발표회 논문집
• /
• pp.909-912
• /
• 2001

This paper presents the validities of the removal time of side forms considering the relationship between rebound number of P type schmidt hammer and compressive strength. According to test results, compressive strength of 40% of W/C at 12 hours shows 16kgf/$cm^{2}$ and 50% of W/C at 15 hours, 13kgf/$cm^{2}$. Rebound number at 9 hours after casting shows 13 and 9 (W/C 40% and W/C 50%). According to the regression analysis, rebound number of P type schmidt hammer to gain 50kgf/$cm^{2}$ of is estimated 20.1. It is thought that desirable rebound number of P type schmidt hammer to gain 50kgf/$cm^{2}$ is determined 25 considering safety factor.

• Structural Engineering and Mechanics
• /
• 제65권5호
• /
• pp.601-609
• /
• 2018

Steel bolts are used in the construction industry for a large variety of applications that range from fixing permanent installations to temporary fixtures. In the past much research has been focused on developing destructive testing techniques to estimate their pull-out load carrying capacity with very little attention to develop non-destructive techniques. In this regards the presented research work details the combined use of ultrasonic pulse velocity and Schmidt hammer tests to identify anchor bolts with faculty installation and to estimate their pull-out strength by relating it to the Schmidt hammer rebound value. From experimentation, it was observed that the load capacity of bolt depends on its embedment length, diameter, bond quality/concrete strength and alignment. Ultrasonic pulse velocity test is used to judge the quality of bond of embedded anchor bolt by relating the increase in ultrasonic pulse transit time to the presence of internal pours and cracks in the vicinity of steel bolt and the surrounding concrete. This information combined with the Schmidt hammer rebound number, R, can be used to accurately identify defective bolts which resulted in lower pull-out strength. 12 mm diameter bolts with embedment length of 70 mm and 50 mm were investigated using constant strength concrete. Pull-out load capacity versus the Schmidt hammer rebound number for each embedment length is presented.

• 한국가스학회지
• /
• 제21권3호
• /
• pp.26-32
• /
• 2017

LNG 저장탱크의 외조 콘크리트는 방호벽 기능을 하는 프리스트레스 콘크리트 구조물이다. 콘크리트 구조물이 열화가 되어 안전성이 확보되지 않는 경우 구조물 붕괴 등의 위험성이 존재하게 된다. 정밀안전진단시 비파괴검사로 반발경도 및 초음파 속도 측정을 통해 구조물의 안전성과 직접적으로 관련되어 있는 콘크리트 압축강도를 추정식으로 예측할 수 있다. 그러나, LNG 저장탱크는 비파괴검사 데이터와 실제 압축강도에 대한 추정식이 부재하다. 이 연구는 LNG 저장탱크에 대해 보다 정확한 실제 강도를 측정하기 위해 Pilot LNG 저장탱크벽체로부터 코어를 채취하였다. 코어를 채취하기 전 해당위치에 일반적인 비파괴시험 방법인 반발경도 검사를 4개의 다른 영역에 각 3군데 위치에서 이루어졌다. 채취한 콘크리트 코어에 대해 압축강도 시험결과의 실제 압축강도 데이터와 반발경도 데이터를 이용하여 LNG 저장탱크의 압축강도 추정식을 개발하였다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2013년도 춘계 학술논문 발표대회
• /
• pp.69-70
• /
• 2013

This is an foundational study to adequacy the non-destruction testing for the estimation of compressive strength of high strength concrete The results are as follows, In high strength concrete, H type is NR type rebound number rather than higher. The relation between rebound number and compressive strength of high strength concrete have lower coefficient. when compressive strength estimation of high strength concrete, it consider that rebound hardness test is not applied and should be consider to combined method or addition method.

• 문화기술의 융합
• /
• 제6권4호
• /
• pp.655-661
• /
• 2020

본 연구에서는 도시철도 지하구조물을 대상으로 동일위치에서의 콘크리트 코어채취 압축강도와 비파괴시험 반발경도를 측정하여 반발경도 범위별 추정식을 도출하고 반발경도 구간별 실측 콘크리트 코어강도와의 비교를 통해 범위에 따른 추정 압축강도의 적정성을 확인하였다. 연구결과, 가우시안 확률밀도 함수를 이용하여 산출한 반발경도 범위별 평균 압축강도의 선형회귀분석 결과(대표 압축강도 추정식)와 반발경도 범위별 추정식은 실측 콘크리트 코어압축강도 실험결과와 약 3% 이내로 잘 일치하는 것으로 나타났다. 본 연구의 반발경도 범위별 압축강도 추정결과는 추정 압축강도의 오차를 줄이고 높은 신뢰수준을 확보할 수 있을 것으로 분석되었다. 따라서 본 연구에서 제안한 반발경도 측정결과를 이용한 확률적 통계분석결과는 추정식에 따라 상대적으로 편차가 크게 나타나는 반발경도와 콘크리트 압축강도간의 상관관계의 신뢰수준을 확보하는 데에 도움이 될 수 있을 것으로 판단된다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 가을 학술발표회 논문집
• /
• pp.239-242
• /
• 2002

This study is intended to investigate the relationship between rebound value of P type schmidt hammer and the compressive strength with various aggregates, and a series of experiments about early strength quality control by P type schmidt hammer was performed. According to the results, the compressive strength of concrete using basalt and limestone aggregate is higher by 3% and lower by 4% than that of concrete using granite aggregate respectively. Concrete using basalt and lime stone aggregate show high rebound value in vertical strike. Estimation of the compressive strength does not show differences in horizontal strike, but the compressive strength is estimated high in order of granite, basalt and limestone aggregate in vertical strike. A good correlation between the rebound value of schmidt hammer and the compressive strength is confirmed regardless of aggregate types, so it could be possible to control the quality of concrete by P type schmidt hammer test when basalt and limestone aggregates are used at the same time.