• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 추계학술대회 초록집
• /
• pp.53.2-53.2
• /
• 2010

In this study, we focused on our specialized electrode process for Si back-contact crystalline solar cell. It is different from other well-known back-contact cell process for thermal aspect and specialized process. In general, aluminum makes ohmic contact to the Si wafer and acts as a back surface reflector. And, silver is used for low series resistance metal grid lines. Aluminum was sputtered onto back side of wafer. Next, silver is directly patterned on the wafer by screen printing. The sputtered aluminum was removed by wet etching process after rear silver electrode was formed. In this process, the silver paste must have good printability, electrical property and adhesion strength, before and after the aluminum etching process. Silver paste also needs low temperature firing characteristics to reduce the thermal budget. So it was seriously collected by the products of several company of regarding low temperature firing (below $250^{\circ}C$) and aluminum etching endurance. First of all, silver pastes for etching selectivity were selected to evaluate as low temperature firing condition, electrical properties and adhesive strength. Using the nano- and micron-sized silver paste, so called hybrid type, made low temperature firing. So we could minimize the thermal budget in metallization process. Also the adhesion property greatly depended on the composition of paste, especially added resin and inorganic additives. In this paper, we will show that the metallization process of back-contact solar cell was realized as optimized nano-paste characteristics.

• 드라이브 ㆍ 컨트롤
• /
• 제18권1호
• /
• pp.31-38
• /
• 2021

This study presents a new principle for driving the robot aimed at reducing the position error for the boresonic examination of turbine rotor. The conventional method of inspection is performed by installing manipulator onto the flange of the turbine rotor and connecting a pipe, which is then being pushed into the bore. The longer the pipe gets, the greater sagging and distortion appear, making it difficult for the ultrasonic sensor to contact with the internal surface of the bore. A pneumatic pressure will ensure the front or rear feet of the robot in close contact with the inner wall to prevent slipping, while the ball screw on the body of the robot will rotate to drive it in the axial direction. The compression force required for tight contact was calculated in the form of a three-point support, and a static structural simulation analysis was performed by designing and modeling the robot mechanism. The driving performance and ultrasonic detection ability have been tested by fabricating the robot, the test piece for ultrasonic calibration and the transparent mock-up for robot demonstration. The tests have confirmed that no slipping occurs at a certain pneumatic pressure or over.

• 한국안전학회지
• /
• 제25권3호
• /
• pp.15-21
• /
• 2010

A differential case equipped with LSD(limited slip differential) has several advantages over a normal type for rear wheel drive vehicles. Specially, the torque distribution can be done between left and right drive wheel in the state of limited slip differential. Also although LSD types are very various according to operating type, medium and torque distribution, a multi-clutch type is generally applied to rear wheel drive vehicles. So, this study presents the analysis of design parameters for development of a friction plate for multi-clutch type LSD using vehicle road test, the simulation of analytical model and the development of vehicle dynamics model by a benchmark product. According to this investigation, the design parameters which are pre-load of coil spring, friction plate and contact area quantity, friction coefficient and TBR(torque bias ratio) for a friction plate are derived from experiment and simulation and consequently, vehicle dynamics model has been constructed for the development of friction plate for multi-clutch type LSD.

• Current Applied Physics
• /
• 제18권12호
• /
• pp.1600-1604
• /
• 2018

This paper reports on a systematic and quantitative assessment of light induced degradation (LID) and regeneration in full Al-BSF and passivated emitter rear contact cells (PERC) along with the fundamental understanding of the difference between the two. After LID, PERC cells showed a much greater loss in cell efficiency than full Al-BSF cells (~0.9% vs ~0.6%) because the degradation in bulk lifetime also erodes the benefit of superior BSRV in PERC cells. Three main regeneration conditions involving the combination of heat and light ($75^{\circ}C/1\;Sun/48h$, $130^{\circ}C/2\;Suns/1.5h$ and $200^{\circ}C/3\;Suns/30s$) were implemented to eliminate LID loss due to BO defects. Low temperature/long time ($75^{\circ}C/48h$) and high temperature/short time ($200^{\circ}C/30s$) regeneration process was unable to reach 100% stabilization. The intermediate temperature/time ($130^{\circ}C/1.5h$) generation achieved nearly full recovery and stabilization (over 99%) for both full Al-BSF and PERC cells. We discussed the effect of temperature, time and suns in regeneration mechanism for two cells.

• 한국결정성장학회지
• /
• 제7권1호
• /
• pp.81-92
• /
• 1997

전극함몰형 태양전지에 후면 부유접합의 도입은 양질의 표면보호를 제공할 수 있어서 효율 향상을 꾀할 수 있다. 이 논문은 PC-1D 모델링을 통하여 후면 부유접합형 태양전지의 효율을 시뮬레이션 분석한 것이다.

• 대한산업공학회지
• /
• 제34권1호
• /
• pp.90-97
• /
• 2008

Wedged insoles are frequently used to reduce the pains caused by the knee arthritis or the foot overuse syndrome. The present study analyzed the effect of wedged rear-foot insoles on the foot pressure in walking. Three medially wedged insoles with three angles (5, 8 and 15") and three laterally wedged insoles with the same angles were made, and a flat insole were prepared. Ten healthy males in twenties walked in a specified line with each insole. Center of pressure (COP), relative vertical force and maximum force on anatomical areas were analyzed from the measured foot pressure data. At heel contact, medially wedged insoles significantly increased the pressure of the medial foot side (COP moved medially by 2-5 mm and maximum pressure of 1st metatarsal head increased by 110-120% relative to the flat insole), In contrast, laterally wedged insoles significantly increased the lateral side pressure (COP moved laterally by 1-5 mm and the ratio of $2^{nd}$ metatarsal head pressure to $1^{st}$ metatarsal head increased by 0.5-2.0 relative to the flat insole). At toe off, both wedged insoles significantly increased the pressure of the medial foot side (COP moved medially by 0.5-10 mm and the ratio of $1^{st}$ metatarsal head pressure to $5^{th}$ metatarsal head increased by 2.0 relative to the flat insole). Especially, the laterally wedged insoles significantly increased the relative vertical force (6-12%) of the rear-foot more than the flat insole.

• 대한기계학회논문집A
• /
• 제26권4호
• /
• pp.787-793
• /
• 2002

In this study, a bar impact test of low velocity was carried out to gain an insight into the damage mechanism and sequence induced in alumina plates(AD 85 and AD 90) under impact conditions. An experimental setup utilizing an instrumented long bar impact was devised, that can measure directly the impact force applied to the specimen and supply a compressive contact pressure to the specimen. During the bar impact testing, the influences of the contact pressure applied along the impact direction to the specimen on the fracture behavior were investigated. The measured impact force profiles explained well the damage behavior induced in alumina plates. The higher contact pressure to the specimen led to the less damage due to the suppression of radial cracks due to the increase in the apparent flexural stiffness of plate. It had produced the change of damage pattern developed in the specimen; from the radial cracks to the local contact stress dominant damage. It would contribute to the improvement of the ballistic property in ceramic plates. The observed results showed the following sequence in damage developed: The development of cone crack at impact region, the formation of radial cracks from the rear surface of plate depending on the plate thickness, the occurrence of crushing within the cone envelope and the fragmentation.

• PNF and Movement
• /
• 제19권2호
• /
• pp.233-242
• /
• 2021

Purpose: The purpose of this study was to determine the changes in foot contact area and pressure when walking with a functional insole that emphasizes the Hallux point as compared to a general insole. Methods: In this study, an experiment was conducted to investigate changes in plantar pressure and contact area for a functional insole that emphasized the Hallux point as compared to a general insole. A lower extremity robot was used for walking reproduction. First, the gait sequence according to the two insoles was determined through a randomized controlled trial comparison. According to the sequence procedure, the insole was attached to the shoe and then worn on the right side of the lower extremity robot for gait reproduction at a normal gait speed of 20 steps per minute. After programming the robot to walk, the experiment was carried out. The result value was determined by averaging the pressure and area data of the fore and rear foot measures after walking at 20 steps per minute. Results: The functional insole that emphasized the hallux point significantly increased the forefoot and rearfoot contact area (p < 0.05) and significantly decreased the forefoot and rearfoot contact pressure (p < 0.05) compared to the general insole. Conclusion: A functional insole that emphasizes the hallux point does not collapse the medial longitudinal arch during gait, increasing foot stability and reducing fatigue. Thus, this functional insole needs to be widely used clinically.

• 한국기계가공학회지
• /
• 제20권6호
• /
• pp.92-99
• /
• 2021

The rotavator is attached to the three-point hitch at the rear of a tractor and uses the power take-off strength of the tractor to perform soil harrowing. During operation, the power transmitted to the gearbox of the rotavator varies with the soil characteristics and depth. These properties influence the reliability of the gearbox. In this study, actual load measurements and analyses were performed using a rotavator. In addition, the safety factor and fatigue life of the gearbox components were determined using the analysis results. Through analysis and tests, the contact pattern of the gear tooth surface was identified. The input power values of the gearbox were minimum and maximum at 54.5% and 84.5% of the tractor power, respectively. Based on the actual load analysis results, the strength and fatigue life of the gearbox components were satisfied. In addition, through the analysis and testing of the gear contact pattern, it was confirmed that a similar contact occurred. Through the analysis, the magnitude of the load acting on the tooth surface of the gear was confirmed.

• 한국세라믹학회지
• /
• 제39권2호
• /
• pp.120-125
• /
• 2002

AC powder EL 소자를 절연층의 유전재료와 후면전극의 전기비저항을 변화시켜 스크린 프린팅법으로 제조하였다. 제조된 소자의 광전기적 특성을 평가하기 위하여 인가 전압은 50∼300 $V_{rms}$까지 변화시켜 휘도 및 전류밀도를 측정하였다. 주파수 및 전압공급원은 정현파 발생 장치로서 frequency generator를 이용하였다. 휘도는 luminometer 의해 측정되었으며 전류밀도 측정을 위하여 multimeter를 사용하였다. 또한 유전층에 대한 유전율을 후막 제조 후 impedance analyser(HP 4194 A)를 이용하여 측정하였다. $TiO_2$ 분말을 $BaTiO_3$에 첨가함에 따라 유전율의 향상으로 초저가형 AC powder EL 소자의 유전층에 적용함으로써 거의 비슷한 전류밀도 하에 50 cd/$m^2$ 정도의 향상된 휘도를 얻을 수 있었다. 저전력 소모형 AC powder EL 소자의 유전층에 적용시 상용분말을 이용한 경우보다 용액 연소법에 의해 제조된 $BaTiO_3$ 분말을 이용한 경우가 더욱 향상된 85 cd/$m^2$ 정도의 휘도를 얻을 수 있었다. 또한 후면전극의 전기 비저항을 조절함으로써 AC powder EL 소자의 휘도는 비교적 감소하지만 전류밀도를 낮출 수 있었다.