• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.72.2-72.2
• /
• 2010

Nowadays, the crystalline Si Solar cell are expected for economical renewable energy source. The cost of the crystalline Si solar cell are decreasing by improvement of its efficiency and decrease of the cost of the raw Si wafers for Solar cells. This Si wafer based crystalline Si solar cell is the verified technology from several decade of its history. Now, I will introduce one method that can be upgrade the efficiency by using simple and economical method. The name of this method is Rear Side Etching(RSE). The purpose of rear side etching is the elimination of n+ layer of rear side and increase of the flatness. The effects of rear side etching are the improvement of Voc and increase of efficiency by reducement series resistance and forming of uniform BSF. The experimental procedure for rear side etching is very simple. After anti-reflection coating on solar cell wafer, Solar cell wafer is etched by the etching chemical that react with only rear side not front side. This special chemical is no harmful to anti-reflection coating layer. It can only etched rear side of solar cell wafer. We can use etching image by optical microscope, minority carrier life time by WCT 120, SiNx thickness and refractive index by ellipsometer, cell efficiency for the RSE effect measurement. The key point of rear side etching is development of etching process condition that react with only rear side. If we can control this factor, we can achieve increase of solar cell efficiency very economically without new device.

• Korean Journal of Applied Biomechanics
• /
• v.17 no.3
• /
• pp.173-180
• /
• 2007

The purpose of study was to compare plantar pressure during walking wearing the curved rear balance and normal shoes. Twelve university students(height: $177.2{\pm}4.6cm$, weight: $68.4{\pm}5.8kg$, age: $26.2{\pm}1.6yrs.$) who have no known musculoskeletal disorders were recruited as the subjects. Plantar foot pressures were evaluated using the Tekscan's pressure measurement systems while subjects walked upright position wearing the curved rear balance and normal shoes in random order at a speed of 1.3 m/s. The contacting dimension, the mean plantar pressure, and the peak plantar pressure were determined for each trial. For each dependent variable, paired t-test was performed to test if significant difference existed between shoe conditions (p<.05). As a result, the curved rear balanced shoes showed as large as 38 up to 50 % of area at the rear side of feet than the normal shoes when measuring the contact area with upright position. In the distribution of average pressure, the curved rear balanced shoes displayed fairly low pressure compared to other normal shoes in general except for one area, which is M2, and especially, the measured pressures at the both rear (M1) and middle (M5) side of feet were low and statically significant. The contact area of the curved rear balanced shoes when walking was significantly larger at the rear (M1) and fore (M6, M7) side of feet. When considering pressure distribution at walking, low pressure was detected at the rear side of feet with the curved rear balanced shoes and at the fore side of feet for other normal shoes. The results showed that the contacting dimension of the curved rear balance shoes that acts between shoes and feet was higher than the corresponding value for the normal shoes in general; therefore it would reduce the pressure to the feet by allowing the each sole of the foot on the ground evenly.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.939-943
• /
• 2004

The side and rear-side collision warning system using fuzzy control algorithms is discussed in this paper. Common rearside warning system has many problems. For example if target vehicle comes into the warning area, it must unconditionally warn. Drivers could be interrupted by it. To solve the problem, I divided measuring area into two sections. One section is blind area of vehicle and the other rear-side area. For blind area, obtained data was filtered inefficient warning signal by using relative velocity method. For rear-side area, a fuzzy logic algorithm is used to recognition of obstacles. According to our experiment relative velocity method and fuzzy logic algorithms were very efficient.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.8 no.1
• /
• pp.64-70
• /
• 2009

This study is to analyze the impact of automotive body with computer simulation. The total deformation, equivalent strain and strain and principal stress are analyzed respectively in case of front, rear and side impacts. The maximum total deformation of side impact is more than 6 times as large as that of rear impact. The maximum equivalent strain or stress of side impact is more than 4 times as large as that of rear impact. These deformation, strain and stress of front impact are a little more than those of rear impact. The maximum principal stress of side impact is more than 4.5 times as large as that of rear impact. This stress of front impact is a little more than that of rear impact.

• Journal of the Korean Society of Mechanical Technology
• /
• v.13 no.1
• /
• pp.49-56
• /
• 2011

The neck injury occupies the most of injury that happened by the rear impact car accident. This study was analyzed about influence of the neck injury in low speed rear impact and car crash accident investigation. There is no neck injury in low speed side rear impact. On the other hand, there is initial neck injury symptom of 10 % but no long-term neck injury symptom in low speed offset rear impact. It appeared that the possibility of neck injury in low speed rear impact is low. For the more study about the neck injury, it should be evaluate the effects of the car body structure, frame structure and rear crash pattern.

• Computational Structural Engineering
• /
• v.10 no.4
• /
• pp.165-175
• /
• 1997

In this paper, the stress, buckling and vibration analyses have been performed for several case with the spot weld stiffened rear side frame, the unstiffened rear side frame and the dual thickness laser weld rear side frame. For stress and vibration analyses, the clamped boundary condition with spring supports are used. But for the buckling analyses, the both ends simply supported boundary conditions are used. For the nummerical analyses, ANSYS 5.0 code is adopted. Maximum stress of the spot weld stiffened rear side frame occurs in the main frame and is 80.9 MPa. Maximum strain is 501 .mu.. The maximum stress of the dual thickness laser weld rear side frame of 1.8mm thickness structure is equal with the stress of spot weld stiffened frame. The weight of dual thickness laser weld frame can be reduced about 17.2%. For the stiffened spot weld rear side frame with both ends simply supported boundary conditon, the bucking load is 52.54 kN. When the thickness of the dual thickness laser weld rear side frame become 1.9mm thickness structure, the buckling load of the stiffenerd rear side frame is equal to that of dual thickness laser weld frame. The reduction of the structure weight is about 5%. The fundamental natural frequency of the stiffened spot weld rear side frame for bending mode is 163.6 Hz and that of the dual thickness laser weld rear side frame is 179.8 Hz.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2002.02a
• /
• pp.144-147
• /
• 2002

In this study, springback analysis of side rear member is carried out. Side rear member is one of the parts which shows severe springback problems. Forming, trimming, flanging and springback stages can be analyzed successively. From forming analysis, we identified the possible spots in which tearing may occur and can prevent failure. In springback analysis we used the boundary conditions same as applied to the blank on the checker so that the computational result can be compared with experimental one. Form .the comparison, springback analysis can yield relatively good results in a qualitative sense. However, in order to get good deformation result quantitatively, there still remains unsettled tasks in the forming analysis with very small die radius. It is found that we have to develop the element with better bending characteristics and precise contact treatment.

• Journal of KIISE:Software and Applications
• /
• v.36 no.8
• /
• pp.653-663
• /
• 2009

In this paper, we propose a blind spots elimination system using three cameras. A wide-angle camera is attached on trunk for eliminating blind spots of a rear-view mirror and two cameras are attached on each side-view mirror for eliminating blind spots of vehicle's sides. In order to eliminate blind spots efficiently, we suggest a method to build a panoramic mosaic view with two side images and one wide-angle rear image. First, we obtain an undistorted image from a wide-angle camera of rear-view and calculate the focus-of-contraction (FOC) in undistorted images of rear-view while the car is moving straight forward. Second, we compute a homography among side-view images and an undistorted image of rear-view in flat road scenes. Next, we perform an image registration process after road and background region segmentation. Finally, we generate various views such as a cylinder panorama view, a top view and an information panoramic mosaic view.

• Transactions of Materials Processing
• /
• v.30 no.5
• /
• pp.236-241
• /
• 2021

This study describes the cold stamping process design procedure to secure the formability and dimensional accuracy of the automotive structural component fabricated by 1.5GPa grade ultra-high strength steel sheet. The target product is selected as the front side rear lower member which is the most important energy absorption part in the frontal impact condition. To secure the product quality, an intermediate product shape is added while considering the low elongation and high strength characteristics of 1470Mart. The sequential optimization procedure of the intermediate product shape, the fine dimensional quality is then achieved without any crack or wrinkling. The cold stamping method with ultra-high strength steel sheets is validated by conducting the die tryout of the front side rear lower member.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.4
• /
• pp.137-145
• /
• 2011

This paper suggests possible rear body shape modifications of a passenger car for the improvement of aerodynamic performance, based on the CFD analysis results. YF SONATA, a passenger car of Hyundai Motors Company, plays a major role as the baseline car in this research. Representatively, three parts(trunk rear edge, side rear edge and rear undercover) are modified in a small range in order for the total outer shapes not to be changed enough so that the modified car is not considered different, compared with the baseline. Specifically, using computational fluid dynamics, aerodynamic drag reduction is accomplished maximally about 11% in this research. Finally, it is proved that although the range of changes of the rear body shapes of a passenger car is very strictly confined, by changing a small range of rear body shapes alone the enhancement of aerodynamic performance of a passenger car can be significantly accomplished.