• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.2
• /
• pp.892-895
• /
• 2003

This paper describes on RIE(Reactive Ion Etching) characteristics of 3C-SiC(Silicon Carbide) grown on Si(100) wafers. During RIE of 3C-SiC films in this work, $CHF_3$ gas is used to form of polymer as a side wall for excellent anisotropy etching. From this process, etch rates are obtained a $60{\sim}980{\AA}/min$ by various conditions such as $CHF_3$ gas flux, $O_2$ addition ratio, RF power and electrode distance. Also, approximately $40^{\circ}$ mesa structures are successfully formed at 100 mTorr $CHF_3$ gas flow ratio, 200 W RF power and 30 mm electrode distance. Moreover, vertical side wall is fabricated by anisotropy etching with 50% $O_2$ addition ratio and 25 mm electrode distance. Therefore, RIE of 3C-SiC films using $CHF_3$ could be applicable as fabrication process technology for high-temperature 3C-SiC MEMS applications.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2001년도 하계종합학술대회 논문집(2)
• /
• pp.25-28
• /
• 2001

In this paper, we have investigated the effects of gas flow rate, rf power, process pressure and Ar addition on reactive ion etching of InP, InGaAs and InAlAs using Sic14 and Cl$_2$ gases. The etch rates were measured by using a surface profiler. The etched profiles, sidewall roughness, and surface morphology were observed by scanning electron microscopy and by atomic force microscopy. The selective etching of InGaAs to InP and InAlAs was studied by varying the etching parameters. It was found that Cl$_2$ gas is more efficient for the selective etching of InGaAs to InAlAs than SiCl$_4$ gas. The etch selectivity of InGaAs to InAlAs is strongly dependent on the rf power and the process pressure.

• 한국전기전자재료학회논문지
• /
• 제11권2호
• /
• pp.101-105
• /
• 1998

This paper describes anisotropic etching technology of highly doped polysilicon. The main etching gases are $Cl_2$ and $SiCl_4$ for reactive ion etching of polysilicon. The mixed $CHCl_3$ to main etching gas makes polymer on etching side wall, so it prevents side etching of polysilicon. The etch rate of polysilicon is increased with increasing RF power. But the etching rate is decreased as the flow rate of $CHCl_3$ is increased with fixed RF power. The etch selectivity of polysilicon and $SiO_2$ is about 12:1. And that of polysilicon and $Si_3N_4$ is about 19:1. In the main etching gas condition, the slope of polysilicon is same as that of photoresist. But in the mixed $CHCl_3$ condition, the slope of polysilicon is larger than that of photoresist. This represents that the polymer made on side wall by added $CHCl_3$ prevents side etching, so anisotropic etching can be possible by polymer.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 1996년도 제11회 학술발표회 논문개요집
• /
• pp.102-103
• /
• 1996

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 1997년도 추계연구발표회 논문개요집
• /
• pp.82-83
• /
• 1997

• 한국진공학회지
• /
• 제6권3호
• /
• pp.242-248
• /
• 1997

기존의 다공질 실리콘 제작 방법인 chemical etching 방법을 병행하면서 새로운 제 작 방법으로서 dry etching 기술을 적용하여 다공질 실리콘을 제작하였다. 또한, 비교를 위 해 E-beam lithography 기술로 실리콘 구조물을 제작하였는데 이 경우 기술상 문제로 약 0.3$\mu\textrm{m}$의 직경을 가진 구조물이 최소의 크기였다. 따라서 새로운 방법으로 4인치 wafer위에 mask 역할을 해주는 다이아몬드 분말을 spin coater로 입힌 후 Reactive Ion Etching(RIE) 방법으로 미세구조의 다공질 실리콘을 제작하였다. 다양한 조건으로 제작된 sample들의 morphology를 SEM과 AFM 등을 이용하여 분석하였고 이 morphology에 대응하는 PL스펙 트럼을 측정하였다. 그 결과, 다이아몬드 분말을 이용한 dry etching방법으로 제작된 다공질 실리콘의 PL peak의 위치가 chemical etching 방법의 다공질 실리콘의 PL peak 위치인 760nm에 비해 높은 에너지인 590nm로 나타났다.

• Transactions on Electrical and Electronic Materials
• /
• 제6권6호
• /
• pp.262-271
• /
• 2005

In order to achieve timely and accurate fault detection of plasma etching process, neural network based time series modeling has been applied to reactive ion etching (RIE) using two different in-situ plasma-monitoring sensors called optical emission spectroscopy (OES) and residual gas analyzer (RGA). Four different subsystems of RIE (such as RF power, chamber pressure, and two gas flows) were considered as potential sources of fault, and multiple degrees of faults were tested. OES and RGA data were simultaneously collected while the etching of benzocyclobutene (BCB) in a $SF_6/O_2$ plasma was taking place. To simulate established TSNNs as incipient fault detectors, each TSNN was trained to learn the parameters at t, t+T, ... , and t+4T. This prediction scheme could effectively compensate run-time-delay (RTD) caused by data preprocessing and computation. Satisfying results are presented in this paper, and it turned out that OES is more sensitive to RF power and RGA is to chamber pressure and gas flows. Therefore, the combination of these two sensors is recommended for better fault detection, and they show a potential to the applications of not only incipient fault detection but also incipient real-time diagnosis.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 G
• /
• pp.2515-2517
• /
• 1998

The micro fresnel lens(MFL) was modeled and fabricated on a XY-stage electrostatically driven by comb actuator. The modeled MFL was approximated as a step shape with 4-phase and 4-zone plate. The focal length and diameter of the MFL is 20mm and 912${\mu}m$, respectively. The XY-stage suspending the MFL is designed to generate a large static displacement up to about 20${\mu}m$. On SOI substrates, we first fabricated MFL using the RIE(reactive Ion etching) technology and then patterned and etched bulk silicon to make XY-stage. After the fabrication of all structures on top side of the SOI substrates. $Si_3N_4$ was deposited for passivation of all structures using PECVD(plasma enhanced chemical vapor deposition). All the MFL systems width comb drive actuator were released by KOH etching from the bottom side of the SOI wafer using double-sided alignment technique. In fabrication of MFL, a dry etching conditions is established in order to improve surface roughness and to control the etched depth.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.473-474
• /
• 2008

This paper proposes that the relative transmittance and emission intensity measured via optical emission spectroscopy (OES) is a useful for fault detection of reactive ion etch process. With the increased requests for non-invasive as well as real-time plasma process monitoring for fault detection and classification (FDC), OES is suggested as a useful diagnostic tool that satisfies both of the requirements. Relative optical transmittance and emission intensity of oxygen plasma acquired from various process conditions are directly compared with the process variables, such as RF power, oxygen flow and chamber pressure. The changes of RF power and Pressure are linearly proportional to the emission intensity while the change of gas flow can be detected with the relative transmittance.

• 마이크로전자및패키징학회지
• /
• 제9권4호
• /
• pp.11-16
• /
• 2002

본 연구에서는 $SrBi_2Ta_2O_9$ (SBT)박막의 고속식각에 따른 잔류물질 및 식각 손상의 영향을 조사하였다. ICP-RIE (inductively coupled plasma reactive ion etching) 의 ICP power와 CCP(capacitively coupled plasma) power를 변화시키면서 고속식각에 따른 박막의 손상과 열화를 XPS 분석과 Capacitance-Voltage (C-V) 측정을 통하여 알아보았다. ICP와 CCP의 power가 증가함에 따라 식각율이 증가하였고 ICP power가 700 W, CCP power가 200 W 일때 식각율은 900$\AA$/min이었다. 강유전체의 건식식각에 있어서 문제점이 플라즈마에 의한 강유전체 박막의 열화인데 반응가스 $Ar/C1_2/CHF_3$를 20/14/2의 비율로 사용하고 ICP와 CCP power를 각각 700w와 200w로 사용하였을 때 전혀 열화되지 않는 강유전체 박막의 특성을 얻을 수 있었다. 본 연구 결과는 Metal-Ferroelectric-Semiconductor (MFS) 또는 Metal-Ferroelectric-Insulator-Semiconductor (MFIS) 구조를 가지는 단일 트랜지스터형 강유전체 메모리 소자를 만드는데 건식 식각이 응용될 수 있음을 보여준다