• 한국철도학회논문집
• /
• 제7권1호
• /
• pp.55-59
• /
• 2004

Composite materials were used widely due to merit of light weight, low maintenance cost and easy installation. But it is the cause of enormous casualties to men and properties because of weak about the fire. Particularly, it is more serious in case of subway train installed composite materials. For this reason, experimental comparison has been done fur measuring heat release rate(H.R.R) and smoke production rate(S.P.R) of interior panels of electric motor car using cone calorimeter. A high radiative heat flux of 50kW/㎡ was used to bum out all materials and to simulate the condition of fully developed fire case in the tests. It was observed that Heat Release Rate and Smoke Production Rate curves were dependent on the kinds of the interior materials. From the heat release rate curves, the sustained ignition time, peak heat release rate and total heat release rate were deduced, These data are useful in classifying the materials by calculating two parameters describing the possibility to flashover.

• Journal of Advanced Marine Engineering and Technology
• /
• 제11권3호
• /
• pp.31-44
• /
• 1987

Nowadays, the problems of energy and environmental pollution become serious day by day and the diesel engine, which has been proved to be superior to gasoline engine with respect to fuel consumption and ecological problems of exhaust gas, has been adopted widely for various purposes from the marine diesel engine and the dynamo engine to all kinds of engine on land. Therefore, extensive parametric studies on combustion of diesel engine should be done for its desing and improvement. To predict the behavior of diesel engien according to variable operating conditions by means of cycle simulation, the reasonable pattern of heat release rate has to be asumed. But it is necessary to know the actual variation of heat release rate in order to assume the reasonable pattern of heat release rate according to the actual operating conditions. In this paper, on a high speed small bore diesel engine with pre-combustion chamber, experimental investigations were carried out to determine the relationship between the heat release pattern and parameters such as engine load and speed. And also, the theoretical investigations about the performance variations of the above diesel engine according to the predicted pattern of heat release rate variation were performed. From the above observations, it may be said that the Fanboro indicator, which was used to get the cylinder pressure, can be used to estimate a reasonable pattern of heat release rate and it is confirmed that the pattern of heat release rate for the pre-combustion type engine is different from that of the direct injection type engine.

• 한국화재소방학회논문지
• /
• 제31권5호
• /
• pp.19-27
• /
• 2017

밀폐된 구획실 화재에서 화원의 면적 및 위치, 화재성장률, 구획 체적의 변화가 열발생률을 포함한 주요 화재특성에 미치는 영향이 검토되었다. 이를 위해 닫힌 개구부가 적용된 ISO 9705 화재실을 대상으로 Fire Dynamics Simulator (FDS)를 활용한 화재시뮬레이션이 수행되었다. 주요 결론으로서, 화원의 면적 및 위치의 변화는 최대 열발생률, 총 열량, 상층부의 최대 온도 및 화학종 농도를 포함한 구획 내의 열적 특성과 화학적 특성에 큰 영향을 주지 않음을 확인하였다. 그러나 화재성장률과 구획 체적의 증가는 최대 열발생률 및 총 열량의 증가를 가져오며, 한계산소농도의 감소 및 최대 CO 농도의 증가를 발생시킨다. 마지막으로 화재성장률과 구획 체적의 함수로 표현된 최대 열발생률의 상관식을 도출하여, 밀폐된 구획실 화재에 대한 화재성장곡선의 적용을 위한 방법론이 제안되었다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제28권7호
• /
• pp.1063-1071
• /
• 2004

Accurate heat release analysis of cylinder pressure data is important for evaluating performance in the development of diesel engine However, traditional single zone first law heat release model(SZM) has significant limitations due to the simplified assumption of uniform charge and neglecting local temperature inside cylinder during combustion process. In this study. heat release rate based on single zone heat release model has been evaluated by comparison with computational analysis results using Fire code which is based on multi-dimensional model(MDM). To overcome limitations due to simplicity of single zone assumption. especially the influence of specific heat ratio on gross heat release has been esteemed and newly suggested were the equation $\gamma$= $\gamma$(${T/T}_{max}$) which describes the variations of gases thermodynamic properties with mean temperature and maximum mean temperature inside cylinder Single zone heat release model applied with this equation is shown to give very good results over whole range of operating conditions when compared with computational analysis results based on multi-dimensional model.

• 한국화재소방학회논문지
• /
• 제32권6호
• /
• pp.28-33
• /
• 2018

건축물 구획공간에 따른 화재성상 및 열방출율을 측정하기 위하여 실물규모 침대 매트리스의 표준화재시험방법(KS F ISO 12949 : 2011)으로 화재시험을 수행하였다. 개방형공간과 구획공간 모두 버너착화 후 초기 약 3분까지는 유사한 화재성장의 경향을 보이는 것으로 확인되었다. 3분후 구획공간에서의 열방출율이 개방형 공간보다 증가되어 높은 것으로 확인되었다. 침대 매트리스(SS)의 경우, 개방형 공간에서의 최대열방출율은 735 kW이며, 구획공간에서의 최대열방출율은 992 kW 로 측정되었다. 침대 매트리스(Q)의 경우 3분후 구획공간에서의 열방출율이 개방형 공간보다 급격하게 증가되는 것으로 확인되었다. 개방형 공간에서의 최대열방출율은 1,087 kW, 이 때의 측정시간은 346s 이며, 구획공간에서의 최대열방출율은 2,127 kW, 이때의 측정시간은 287 s 측정되어 구획공간에 따른 최대열방출율 및 측정시간의 차이가 확인되었다.

• 한국분무공학회지
• /
• 제8권4호
• /
• pp.9-16
• /
• 2003

The Purpose of this study is to investigate the relationships between the local heat release rate and CH concentration have been investigated by numerical simulations of methane-air premixed flames. And simultaneous CH and OH PLIF(Planar Laser Induced Fluorescence) measurement has been also conducted for lean premixed flame as well as for laminar flames. Numerical simulations are conducted for laminar premixed flames and turbulent ones by using PREMIX in CHEMKIN and two dimensional DNS code with GRI mechanism version 2.11, respectively. In the case of laminar premixed flame, the distance between the peak of heat release rate and that of CH concentration is under $91{\mu}m$ for all equivalence ratio calculated in present work. Even for the premixed flame in high intensity turbulence, the distribution of the heat release rate coincides with that of CH mole fraction. For CH PLIF measurements in the laminar premixed flame burner, CH fluorescence intensity as a function of equivalence ratio shows a similar trend with CH mole fraction computed by GRI mechanism. Simultaneous CH and OH PLIF measurement gave us useful information of instantaneous reaction zone. In addition, CH fluorescence can be measured even for lean conditions where CH mole fraction significantly decreases compared with that of stoichiometric condition. It was found that CH PLIF measurements can be applicable to the estimation of the spatial fluctuations of heat release rate in the engine combustion.

• 한국자동차공학회논문집
• /
• 제12권2호
• /
• pp.17-23
• /
• 2004

A cylindrical constant volume combustion bomb is used to investigate the combustion characteristics and to analyze the heat quantity of homogeneous charge methane-air mixture under various initial pressures, excess air ratios and ignition times. As the overall pressure increase, the values of maximum combustion pressure, maximum heat release rate and cumulative heat release have been increased. But it is not very meaningful to compare with some values such as maximum combustion pressure, maximum heat release rate and cumulative heat release for different overall pressure due to the different heat energy of supplied fuel. So the each value is needed to be compared with normalized value, which is divided by the entered fuel energy. To analyze the heat quantity, some definitions including the CHR ratio, the UHC ratio and the HL ratio are needed and are calculated. As the overall pressure increase, the CHR ratios and the UHC ratios have been decreased, while the HL ratios have been increased. The CHR ratio of 300 ms has the higher value than that of 10000ms, and the HL ratios of 300 ms have a lower value.

• 한국화재소방학회논문지
• /
• 제26권1호
• /
• pp.16-22
• /
• 2012

화재시험에 있어서 정확한 발열량의 측정은 시험체의 화재 안정성을 결정하기 위한 중요한 정보이다. 발열량 측정값은 측정 인자들의 오차에 기인하여 영향을 받는다. 본 연구에서는 한국철도기술연구원에 설치된 룸코너 시험기에 대한 불확도의 인자를 분석하였고 이를 이용하여 KTX 내장재 화재시험의 발열량 측정 불확도를 계산하였다. 화재 발열량 불확도 계산 결과, 화재시작단계에서 불확도가 매우 높은 값으로 나타났고 화재가 성장하면서 불확도는 점차적으로 감소하였다. 불확도 인자들 중 산소 농도가 발열량 측정 불확도에 가장 크게 기여하는 것으로 나타냈다.

• 한국화재소방학회논문지
• /
• 제17권3호
• /
• pp.26-30
• /
• 2003

본 논문은 화재발생시 열감지기가 오동작하는 특성을 열방출률(Heat Release Rate : HRR)을 이용하여 경계값을 정량적으로 나타내고 그 경계값을 기준으로 감지기의 오동작 영역을 분석하였다. Crib 형태의 목재를 가지고 small-scale의 화재실험을 통하여 화재감지기의 동작시간 등을 측정하였고 이를 이용하여 화재감지기가 동작하는 순간의 HRR을 계산하였다. 화재실험으로부터 얻은 변수를 가지고 화재감지기가 오동작하는 HRR의 경계값을 계산한 결과 정온식 감지기는 20.24 kW 차동식 감지기는 13.59 kW로 나타났다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2003년도 추계학술대회 논문집(III)
• /
• pp.295-300
• /
• 2003

Experimental comparison was done for measuring Heat Release Rate and Smoke Production Rate of electric motor car's interior panels using cone calorimeter. Radiative heat flux of $50kW/m^2$ was used to simulate the condition of fully developed fire case in the tests. It was observed that Heat Release Rate and Smoke Production Rate curves were shown differently according to interior materials. From experiment's results we can deduce that materials having higher rate of heat release smolder more smoke. It needs to establish fire risk propensity of each material and to set up the standards urgently.