• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.2101-2104
• /
• 2003

Experimental investigations are performed for the rarefied gas flows in a disk-type drag pump (DTDP). The pump considered in this paper consists of grooved spiral channel on rotors and planar stators. The flow-metre method is adopted to calculate the pumping speed. Compression ratio and pumping speeds for the nitrogen gas are measured under the inlet pressure range of $0.001{\sim}4$ Torr. The maximum of compression ratio was about 3300 for three-stage DTDP, 1000 for two-stage and 100 for single-stage DTDP at zero throughput. The number of stage influences the pumping speed of DPDT

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.47 no.3
• /
• pp.169-176
• /
• 2019

In the present study, a CFD/DSMC hybrid method performed by a coupled analysis between the CFD method and the DSMC method was developed to obtain the flow information on the rarefied gas flows effectively. Flow simulations around the high speed vehicles on the transition flow regimes were conducted by using the developed method. The FRESH-FX vehicle made of cone and cylinder shapes was considered for the simulations. The results of the hybrid method were compared with the results of the pure CFD and the pure DSMC method to confirm the reliability and efficiency of the hybrid method. It was found that the gradient and the intensity of the shock waves were weakened due to the relatively low density on the transition flow regime. It was confirmed that the results of the hybrid analysis were different to those of the pure CFD analysis and almost identical to those of the pure DSMC analysis. In addition, the computational time of the hybrid method was reduced than that of the pure DSMC method. As a result, it was obtained that the validity and the efficiency of the CFD/DSMC hybrid method.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.10
• /
• pp.947-954
• /
• 2009

Starting from the Eu's GH(Generalized Hydrodynamic) theory, the multi-species GH numerical solver is developed in this research and its computatyional behaviors are examined for the hypersonic rarefied flow over an axisymmetric body. To improve the accuracy of the developed multi-species GH solver, various slip-wall boundary conditions are tested and the computed results are compared. Additionally, in order to validate the entropy characteristics of the GH equation, the entropy production and entropy generation rates of the GH equation are investigated in the 1-dimensional normal shock structure test at a high Knudsen number.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2000.11a
• /
• pp.3-3
• /
• 2000

저추진력 추력기라는 것은 추력이 수 N 정도, 노즐출구직경이 수 mm 정도의 소형추력기를 의미하며, 주로 인공위성을 비롯한 우주 비행체의 자세제어, 궤도천이 등의 목적을 위해 사용된다. 따라서, 저추진력 추력기의 일반적인 작동환경은 연속체 영역, 천이영역(transition flow regime), 희박영역(rarefied flow regime)을 모두 포함하므로, 기존의 연속체 유체역학에서 사용되는 Navier-Stokes 방정식을 사용할 수 없고, 분자들의 미시적인 움직임과 내부 에너지 분포를 고려한 Boltzmann 방정식을 이용한 해석을 수행하여야 한다.(중략)

• Proceedings of the KSME Conference
• /
• 2000.11b
• /
• pp.597-602
• /
• 2000

In a MEMS(micro-electro mechanical system), the fluid may slip near the surface of a solid and have a discontinuous temperature profile. A numerical prediction in this slip flow region can provide a reasonable guide for the design and fabrication of micro devices. The compressible Navier-Stokes equation with Maxwell/smoluchowski boundary condition is solved for two simple systems; couette flow and pressure driven flow in a long channel. We found that the couette flow could be regarded as an incompressible system in low speed regions. For the pressure driven flow system, we observed nonlinear distribution of pressure in the long channel and numerical results showed a good agreement with the experimental results.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.178-181
• /
• 2011

Recently, micro shock tube is being extensively used in various fields of engineering applications. The flow characteristics occurring in the micro shock tube may be significantly different from that of conventional macro shock tube due to very low Reynolds number and Knudsen number effects which are, in general, manifested in such flows of rarefied gas, solid-gas two-phase, etc. In these situations, Navier-Stokes equations cannot properly predict the micro shock tube flow. In the present study, a two-dimensional CFD method has been applied to simulate the micro shock tube, with slip velocity and temperature jump boundary conditions. The effects of wall thermal conditions on the unsteady flow in the micro shock tube were also investigated. The unsteady behaviors of shock wave and contact discontinuity were, in detail, analyzed. The results obtained show much more attenuation of shock wave, compared with macro-shock tubes.

• International Journal of Aeronautical and Space Sciences
• /
• v.1 no.2
• /
• pp.1-8
• /
• 2000

The flow in low-density plumes expanding into a region of finite pressure shows a quite different behavior from that observed in low-density plumes expanding into a vacuum. The flow structure in the plume varies depending on applied ambient and stagnation chamber conditions. In the present study, the direct simulation Monte-Carlo (DSMC) method based on molecular gas dynamics is employed in the analysis of low-density gas flows expanding through a small converging/diverging nozzle. Special attention has been paid to the effect of non-zero ambient and stagnation pressures on the flow structure which has rarely been studied using the DSMC method.

• Advances in aircraft and spacecraft science
• /
• v.4 no.5
• /
• pp.503-514
• /
• 2017

The attitude control of an aircraft is usually fulfilled by means of thrusters at high altitudes. Therefore, the possibility of using also aerodynamic surfaces would produce the advantage of reducing the amount of fuel for the thrusters to be loaded on board. For this purpose, Zuppardi already considered some aerodynamic problems linked to the use of a wing flap in a previous paper. A NACA 0010 airfoil with a trailing edge flap of 35% of the chord, in the range of angle of attack 0-40 deg and flap deflections up to 30 deg was investigated. Computer tests were carried out in hypersonic, rarefied flow by a direct simulation Monte Carlo code at the altitudes of 65 and 85 km of Earth Atmosphere. The present work continues this subject, considering the same airfoil and free stream conditions but two flap extensions of 45% and 25% of the chord and two flap deflections of 15 and 30 deg. The main purpose is to compare the influence of the flap dimension with that of the flap deflection. The present analysis is carried out in terms of: 1) percentage variation of the global aerodynamic coefficients with respect to the no-flap configuration, 2) increment of pressure and heat flux on the airfoil lower surface due to the Shock Wave-Shock Wave Interaction (SWSWI) with respect to the same quantities with no SWSWI or in no-flap configuration, 3) flap hinge moment. Issues 2) and 3) are important for the design of the mechanical and thermal protection system and of the flap actuator, respectively. Under the above mentioned test and geometrical conditions, the flap deflection is aerodynamically more effective than the flap extension, because it involves higher variation of the aerodynamic coefficients. However, tests verify that a smaller deflection angle involves the advantage of a smaller increment of pressure and heat flux on the airfoil lower surface, due to SWSWI, as well as a smaller hinge moment.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.7
• /
• pp.90-97
• /
• 2002

Wall slip models are essential to the study of nonequilibrium gas transport in rarefied and microscale condition that can be found in gas flows associated with aerospace vehicle, propulsion system, and MEMS. The Maxwell slip model has been used for this type of problem, but it has difficulty in defining the so-called accommodation coefficient and has not been very effective in numerical implementation. In the present study, on the basis of Langmuir's theory of the adsorption of gases on metals, a physical slip model is developed. The concept of the accommodation coefficient and the difference of gas particles are clearly explained in the new model. It turned out that the Langmuir model recovers the Maxwell model in the first-order approximation. The new models are also applied to various situations including internal flow in a microchannel. Issues of validation of models are treated by comparing analytic results with experiment.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.2
• /
• pp.1-11
• /
• 2002

In the present study, a parallel DSCM technique based on a cell-based data structure is developed for the efficient simulation of rarefied gas flows especially od PC clusters. Dynamic load balancing is archieved by decomposing the computational domain into several sub-domains and accounting for the number of particles and the number cells of each domain. Mesh adaptation algorithm is also applied to improve the resolution of the solution and to reduce the grid dependency. It was demonstrated that accurate solutions can be obtained after several levels of mesh adapation starting from a coars initial grid. The method was applied to a two-dimensioanal supersonic leading-edge flow and the axi-symmetric Rothe nozzle flow to validate the efficiency of the present method. It was found that the present method is a very effective tool for the efficient simulation of rarefied gas flow on PC-based parallel machines.