• Transactions of Materials Processing
• /
• v.16 no.5 s.95
• /
• pp.354-359
• /
• 2007

Effects of forging and mechanical properties of 6061 aluminum alloy wheel for automobiles were investigated in the present study. Microstructural and tensile characteristics of automobile wheel after hot forging process using dynamic screw press were analyzed to evaluate effect of metal flow on mechanical properties. The results showed advanced mechanical properties of 6061 alloy wheel because of $Mg_2Si$ precipitation by T6, elongated grain by forging, and work hardening by dense metal flow, etc. Hot compression tests were conducted in order to characterize high temperature compression deformation behaviors and microstructural variation in the range of $300{\sim}450^{\circ}C$, in the strain rate range of $10^{-3}{\sim}10^1\;sec^{-1}$. As strain rate increased, maximum compression stress increased but it was shown the reverse linear relation between temperature and maximum stress irrelevant to strain rate variation. On the other hand, temperature and yield stress didn't have any linear relation and its relation showed big deviation by a function of strain rate and test temperature.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.3
• /
• pp.437-441
• /
• 2012

In this paper, we have designed and manufactured 10MHz power source for the application of short distance wireless power transmission. The designed power source consists of a DDS(direct digital synthesizer) signal generator, a buffer driver and a balanced power amplifier. Short range wireless power transmission is usually carried out by near-field inductive coupling between source and load. The distance variation between source and load gives rise to the change of load impedance of power amplifier, which has effect on the operation of power amplifier. To overcome this problem due to load variation of power amplifier, we have adopted the balanced power amplifier using the quadrature hybrid implemented by lumped capacitors and a mutually coupled coil. The experiment results show the above 40dBm output power, frequency range of 9 to 11MHz, and total DC power consumption of 36W.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.13 no.1
• /
• pp.31-39
• /
• 1995

We have various methods of measurement for a safety diagnosis of outworn structure, but these methods to find a variation of structure are not convincible with it's exactness and confidence. We have to lay out a scheme for a solution of these problems and improve a visibility of result. In this study, we studied a optimized solution for close-range photogrammetry to offer the more reliable method compare to conventional method and to improve it's confidens and visibility of output. For obtaining these effects, we manufactured the plane models and curved surface ones each devided into two types, normal case and obilique case. In this way, we got a optimum solution to increase a confidence level and visibility of photogrammetry. And actually, this study will be a good way to measure a variation of structures.

• Journal of electromagnetic engineering and science
• /
• v.12 no.2
• /
• pp.176-184
• /
• 2012

In this paper, the effects of a metal plane on the performance of a meandered slot RFID antenna are evaluated in a real environment, and 3 metal plane cases are considered (the most likely scenarios in which metal conductive materials are placed near the tag antenna). The metal plane effects can be categorized as matching degradation and antenna gain variation. First, matching degradation due to the antenna's induced mutual impedance is experimentally investigated. In addition, the gain variation is investigated to figure out the change in the radiation characteristics. With the derived antenna parameters, the read range is calculated with the Friis transmission equation and measured to analyze the effects of a metal plane on RFID system performance. The calculated and measured read range varies from 9.3 m to 19.1 m as the distance between the RFID antenna and the metal plane changes.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.13 no.2
• /
• pp.219-228
• /
• 1995

The facilities of electric power plant which were constructed in and after the 1960's are superannuated in these days. We are expanding them applying an incressary to secure a safe plan for them. In this study, for a feasibility of management plan in electric power structure, a RC test prame was manufactured for monitoring and calculation of variation using close range photogrammetry. On the basis of this data, monitoring and calculating of variation in soil wall building site were carried out. Also a survey and analysis of a influence which occured to a structure near by exactitude site. All of these afford data for a management plan in electric power structure.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.5 no.2
• /
• pp.8-14
• /
• 1968

A linear current-pulse discriminator consisting: of a transistor monostable multivibrator and a Si tunnel diode is described. The input currant pulse range is about 50$\mu$A~5.23mA. The measured maximum linearity deviation is $\pm$0.75% in the input current pulse range mentioned above. The pulse resolving ability of the discriminator measured depends upon the bias current through the T, D. ; and, under the reverse bias current of 3mA, the resolving time is 2rs if allow the excess pulse amplitude of 5%. The threshold stability of the discriminator depends mainly upon the stability of the peak current Ip of the T. D. ; and, under the ambient temperature variation from $0^{\circ}C$ to 5$0^{\circ}C$, no bigger threshold variation than the maximum linearity deviation, i. e. $\pm$ 0.75%, was observed.

• Journal of electromagnetic engineering and science
• /
• v.13 no.2
• /
• pp.93-103
• /
• 2013

This paper presented a novel approach for the design of a tunable dual-band bandpass filter (BPF) with independently tunable passband center frequencies and bandwidths. The newly proposed dual-band filter principally comprised two dual-mode single band filters using common input/output lines. Each single BPF was realized using a varactor-loaded transmission line resonator. To suppress the harmonics over a broad bandwidth, a defected ground structure was used at the input/output feeding lines. From the experimental results, it was found that the proposed filter exhibited the first passband center frequency tunable range from 1.48 to 1.8 GHz with a 3-dB fractional bandwidth (FBW) variation from 5.76% to 8.55%, while the second passband center's frequency tunable range was 2.40 to 2.88 GHz with a 3-dB FBW variation from 8.28% to 12.42%. The measured results of the proposed filters showed a rejection level of 19 dB up to more than 10 times the highest center frequency of the first passband.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.11
• /
• pp.2287-2296
• /
• 2002

Most cracks in the structure occur under mixed mode loading and those fatigue crack propagation behavior heavily depends on the stress ratio. So, it is necessary to study the fatigue behavior under mixed mode loading as the stress ratio changes. In this paper, the fatigue crack propagation behavior was respectively investigated at stress ratio 0.1, 0.3, 0.5, 0.7 and we changed the loading application angle into 0$^{\circ}$, 30$^{\circ}$, 60$^{\circ}$ to apply various loading mode. The mode I and II stress intensity factor of CTS specimen used in this study was calculated by the displacement extrapolation method using FEM (ABAQUS). Using both the experiment and FEM analysis, we have concluded the relationship between crack propagation rate and stress intensity factor range at each loading mode due to the variation of stress ratio. Also, when the crack propagated under given stress ratio and loading mode condition, we have concluded the dominant factors of the crack propagation rate at each case.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2007.06a
• /
• pp.630-633
• /
• 2007

In this paper, a blind watermarking method using binary images as watermarks is proposed. In order to enhance the detection capability against various attacks that transform watermarked image, the method uses asymmetric thresholds for inserting and detecting. Also, in order to reduce errors in the detected value of watermarks according to small changes in the coefficient values when detecting watermarks, it set the range for movement variation of the coefficients and lowered the sensitivity of variation by ignoring the variations that fall into this range. The experimental results show that the proposed method has good quality and is robust to various attacks such as the JPEG lossy compression, noise addition, cropping, blurring etc.

• Proceedings of the KSME Conference
• /
• 2001.11a
• /
• pp.286-291
• /
• 2001

Most cracks in the structure occur under mixed mode loadings and those propagation depend on the stress ratio very much. So, it is necessary to study the fatigue behavior under mixed mode loading as stress ratio changes. In this paper, fatigue crack propagation behavior was investigated respectively at stress ratio 0.1, 0.3, 0.5, 0.7 and we change loading application angle to $0^{\circ},\;30^{\circ},\;60^{\circ}$ to apply various loading. mode. The mode I and II stress intensity factors of CTS specimen used in this study were calculated by displacement extrapolation method using FEM(ABAQUS). Using both the study through the experiment and the theoretical study through FEM analysis, we studied the relation between crack propagation rate and stress intensity factor range at each loading mode due to the variation of stress ratio. Also, when the crack propagated under given stress condition and given loading mode condition, we studied what the dominant factors of the crack propagation rate were at each case.