• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.21 no.5
• /
• pp.11-18
• /
• 2021

The small radio frequency tracking radar is a tracking system with a radio frequency sensor that identifies a target through all-weather radio frequency signal processing for a target and searches, detects and tracks the target for the major target. In this paper, we describe the development of a board equipped with TMS320C6678 and XILINX FPGA (Field Programmable Gate Array), a high-speed multi-core DSP that acquires target information through all-weather radio frequency and identifies a target through real-time signal processing. We propose DSP-FPGA combination architecture for DSP and FPGA selection and signal processing, and also explain the design of SRIO for high-speed data transmission.

• Current Optics and Photonics
• /
• v.5 no.3
• /
• pp.213-219
• /
• 2021

We describe a single-channel rubidium (Rb) radio-frequency atomic magnetometer (RFAM) as a receiver that takes magnetic signal resonating with Zeeman splitting of the ground state of Rb. We optimize the performance of the RFAM by recording the response signal and signal-to-noise ratio (SNR) in various parameters and obtain a noise level of 159 $fT{\sqrt{Hz}}$ around 30 kHz. When a resonant radiofrequency magnetic field with a peak amplitude of 8.0 nT is applied, the bandwidth and signal-to-noise ratio are about 650 Hz and 88 dB, respectively. It is a good agreement that RFAM using alkali atoms is suitable for receiving signals in the very low frequency (VLF) carrier band, ranging from 3 kHz to 30 kHz. This study shows the new capabilities of the RFAM in communications applications based on magnetic signals with the VLF carrier band. Such communication can be expected to expand the communication space by overcoming obstacles through the high magnetic sensitive RFAM.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.8A
• /
• pp.730-740
• /
• 2011

The Korean radio broadcasting system is analog. Compared with digital radio, the analog radio decreases the frequency efficiency. HD Radio is the method where the digital signal is transmitted on either side of the analog PM signal. Therefore, without relocating the analog frequency can transmit digital signals. If interference between analog and digital signal occurs it is impossible to receive smoothly, so HD Radio interference with existing analog PM will be analyzed. In this paper, based on Mt.Gwae-Bang stations within +-400kHz frequency of l03.5MHz, and to use the station to station by specifying the HD Radio channel interference, place the structures were analyzed. Through this paper, the reader of a digital radio frequency interference in the system know that it may obtain information about.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.6 no.5
• /
• pp.401-406
• /
• 2005

Digital memory circuits have been developed very fast according to the progress of semiconductor technology. But it was very difficult to memorize a wideband radio frequency signals. Many years ago, an analog frequency memory loop(FML) was used for store of radio frequency signal and the digital radio frequency memory was made according to the development of wideband amplifier and high speed sampler. We present a design of wideband digital radio frequency reproduction device using ladder circuit and the simulation results with respect to the sampling speed in this paper.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.8 no.11
• /
• pp.3789-3809
• /
• 2014

Radio environment maps (REMs) and geolocation database represent an important source of information for the operation of cognitive radio networks, replacing or complementing spectrum sensing information. This paper provides a survey of methods for constructing the radio frequency layer of radio environment map (RF-REM) using distributed measurements of the signal levels at a given frequency in space and time. The signal level measurements can be obtained from fixed or mobile devices capable of sensing radio environment and sending this information to the REM. The signal measurements are complemented with information already stored in different REM content layers. The combined information is applied for estimation of the RF-REM layer. The RF-REM construction methods are compared, and their advantages and disadvantages with respect to the spatial distribution of signal measurements and computational complexity is given. This survey also indicates possible directions of further research in indirect RF-REM construction methods. It emphasizes that accurate RF-REM construction methods should in the best case support operation with random and clustered signal measurements, their operation should not be affected by measurements outliers, and it must estimate signal levels comparably on all RF-REM locations with moderate computational effort.

• ETRI Journal
• /
• v.45 no.2
• /
• pp.277-290
• /
• 2023

This paper proposes a method that can reduce the complexity of a system matrix by analyzing the characteristics of a pseudoinverse matrix to receive a binomial frequency division multiplexing (BFDM) signal and decode it using the least squares (LS) method. The system matrix of BFDM can be expressed as a band matrix, and as this matrix contains many zeros, its amount of calculation when generating a transmission signal is quite small. The LS solution can be obtained by multiplying the received signal by the pseudoinverse matrix of the system matrix. The singular value decomposition of the system matrix indicates that the pseudoinverse matrix is a band matrix. The signal-to-interference ratio is obtained from their eigenvalues. Meanwhile, entries that do not contribute to signal generation are erased to enhance calculation efficiency. We decode the received signal using the pseudoinverse matrix and the removed pseudoinverse matrix to obtain the bit error rate performance and to analyze the difference.

• Proceedings of the Korea Contents Association Conference
• /
• 2004.05a
• /
• pp.372-376
• /
• 2004

Digital memory circuits have been developed very fast according to the progress of semiconductor technology But It was very difficult to memorize a high frequency radio signal. Many years ago an analog loop was used for store of radio frequency signal, and the digital radio frequency memory was made to the development of wideband amplifier and high speed sampler. We present a design of wide-band DRFM using Johnson code and the simulation results with respect to the sampling speed. in this paper.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.10
• /
• pp.2189-2196
• /
• 2009

Theoretical analysis is presented for expending of the usable frequency range of optoelectronic mixing detection in the radio over fiber network system. We define the normalized gain to evaluate the performance of the optical mixing detection, and conform the possibilities of detection for the high frequency signals beyond the cutoff frequency of a photodiode. Optical mixing detection mechanism is analyzed by solving the continuity equation for the carriers of a photodiode. The normalized gain is independent on the signal frequency and the frequency difference between the optical signal and the local signal. Also, the amplitude of the local signal and the bias voltage are needed to be optimized at the same time in order to maximize the normalized gain.

• Journal of Convergence for Information Technology
• /
• v.9 no.8
• /
• pp.134-139
• /
• 2019

This paper describes the effect of multiple signal regeneration in quadrature digital radio frequency memory(DRFM). Single channel DRFM have good reproducibility after storing a single signal. However, when reproduced after storing multiple signals, the spurious signal is large. The quadrature DRFM consists of I and Q channels, which can greatly reduce the spurious signal. The amplitude of the spurious signal depends on the number of bits of data stored in the DRFM. In this paper, we have obtained the number of bits of signal regeneration according to the application of radio frequency memory by obtaining the size of the spurious signal according to the number of bits of the stored data of the DRFM for multiple signals. As a result of this study, 4 bits quadrature DRFM can achieve a spurious output of less than -20dB, which is used for 4 signals. Those are expected to greatly contribute to the signal analysis of electronic warfare equipment and the development of jamming device.

• Proceedings of the IEEK Conference
• /
• 2002.07b
• /
• pp.1346-1349
• /
• 2002

This paper presents the design and implementation of 16-QAM modem that can be applied to fixed broadband wireless access systenm. It is implemented in the hardware prototype that consist of FPGA(Field Programmable Gate Array) for digital signal processing and analog front end module for analog signal processing. We provide 20.48Mbps data rate using implemented modem and test the modem in KOREA 26㎓ broadband wireless local loop system including IFU(Intermediate Frequency Unit) and RFU(Radio Frequency Unit) via air interface.