• Tribology and Lubricants
• /
• v.14 no.3
• /
• pp.94-99
• /
• 1998

Generally not only the radial load but also the moment may be applied to the ball bearings for a shaft system. However it has been difficult to determine the static equivalent load because there is the radial static equivalent equation only for the axial and radial force on the bearings. In this paper, the same static equivalent radial load which makes the maximum contact force at the interface between the ball and groove as the applied radial force and moment generate is calculated under the condition that the radial force and the moment are applied to the bearings simultaneously. The relation between the static equivalent load and applied force is studied. Therefore the simple and effective equation for the static equivalent radial load of the radial load and moment is proposed for the deep groove ball bearings.

• Tribology and Lubricants
• /
• v.31 no.5
• /
• pp.221-228
• /
• 2015

It is possible to prevent a piston from contacting the cylinder by changing the shape of the piston or by applying micro-textures, such as micro-grooves or micro-holes, over the piston surface. Usually, the minimum radial clearance reaches its minimum value at the beginning of the suction stroke because the pressure around the piston is low and almost axisymmetric such that the net pressure force on the piston is not sufficiently high to support the piston from touching the cylinder. In this study, we apply a series of saw-tooth-shaped grooves on the piston surface, and numerically investigate the effects of groove depth, groove angle, and the number of grooves with radial clearance variations using a finite difference method. We conduct a dynamic analysis of the piston for various changes in groove geometries to obtain the minimum radial clearance variation for the entire compression cycle. The minimum radial clearance increases while friction loss decreases when we apply the series of saw-tooth-shaped grooves on the piston. In addition, we analyze the impact of the change in the groove shape variable due to changes in radial clearance. Leakage variations are relevant to radial clearance, but have almost no effect on the groove parameters.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.6
• /
• pp.2760-2766
• /
• 2013

Introduction : The projection method to check existence and nonexistence of radius groove penetration of screw after distal radius fracture operation clinical using the T-type plate and the radiation of radial groove tangential is to propose a new test. Material and Methods : On the tangential projection view of radius groove, elevation angle of distal radius is 2.5, 5, 7.5, 10 degree. and forearm and radiation detector of angle is 60, 70, 80, degree each changed. that analyzed check existence and nonexistence of radius groove penetration of screw. Results : For the image of Radial groove tangential. the case of not radius groove penetration of screw(63.95%, n=55), medial penetration of radius groove(10.47%, n=9) or lateral penetration of radius groove(25.58%, n=22) was analysis. The radius groove penetrating of screw length was a range of 0.43 ~ 2.72mm, the average was 1.06mm. the check existence and nonexistence of radius groove penetration of medial or lateral was analysis that it accurate for the image of Radial groove tangential. the radiography of radial groove is well described elevation angle of distal radius 2.5 to 7.5 degree(90% over), forearm and radiation detector of angle 70degree(80%over) Conclusion : It is elevation angle of distal radius is 5degree, forearm and radiation detector of angle 70degree recommended.

• Proceedings of the KSME Conference
• /
• 2001.06c
• /
• pp.438-444
• /
• 2001

The objective of this study is to provide a simple methodology to find optimum processing conditions to fabricate sub-micron structured DVD-RAM substrates with superb optical and geometrical properties. It was found that the birefringence, which is regarded as one of the most important optical properties for an optical disk, was very sensitive to the mold wall temperature history. Also, the integrity of the replication, represented by the land-groove structure and the radial tilt were influenced by the mold temperature and the compression pressure. A set of optimum conditions were obtained by applying Design of Experiment and the objective functions composed of three different objectives.

• Proceedings of the Acoustical Society of Korea Conference
• /
• 1987.11a
• /
• pp.39-39
• /
• 1987

자동차에서 발생되는 소음은 여러 가지 발생원으로부터의 복합적인 것으로서 차량의 속도가 고속화하면서 타이어 소음의 기여도가 매우 커지는 것으로 알려져 있다. 타이어 소음은 근본적으로 노면과 타이어의 상호작용에 의하여 발생되는 데 타이어/노면의 상호작용에 영향을 미치는 인자로는 마모상태, 차량속도, 하중, 공기압, carcass 구조, 타이어 온도등 여러 가지가 있으나 tread 모양과 노면의 상태에 가장 크게 영향을 받는다. 본 연구에서는 승용차용 155SR13 radial 타이어를 대상으로 하여 실내에 설치된 dynamometer를 이용하여 groove 의 개수, groove 길이, groove 폭, groove 깊이, groove 방향 등 트레드 패턴 인자가 발생소음에 미치는 기여도를 실험적으로 측정하고 트레드 패턴형상에 따른 소음도를 예측할 수 있는 실험식을 구했다. 또한 단일 groove 내에서 발생되는 소음의 시간신호를 측정하여 모델화하고 차량속도와 groove 사이의 간격에 따른 시간신호를 합성하고 이 신호로부터 FFT 알고리듬을 통해 소음 spectrum을 구하는 소음 예측 프로그램을 개발하였다. 비교적 단순한 tread 패턴에 대해 이를 적용한 결과 실험적으로 구한 spectrum과 상당히 유사함을 볼 수 있었다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.7
• /
• pp.1654-1663
• /
• 1994

Even if the ball bearing was conservatively designed considering the dynamic capacity and the rating life, sometimes the bearing was early failed on account of the misalignment and the lubricant contaminations etc. Misalignment was generated when bearing-shaft system transmitted large power and when the bearing was inadequately mounted. It was possible to predict the fatigue life of ball bearing under the misalignment considering the motions of ball, cage and raceway, and the factors of the effect on fatigue life. Misalignment affected on ball bearing as radial and moment load and the relationships between misalignment and moment were obtained. In this paper, the analysis of the load distributions between ball and raceway, and the prediction of fatigue life of deep groove ball bearing under radial and moment loads were carried out. And, the new formulation of equivalent dynamic load considering the effects of moment load was proposed.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.2 s.95
• /
• pp.23-30
• /
• 1999

This paper investigates the radial performance of self-acting spiral-grooved air bearing, used to support small high-speed rotating bodies. Repeatable runout, nonrepeatable runout, stiffness and supporting load are selected as the performance. The clearance between rotor and stator, the stator groove depth, and the rotating speed are chosen as three main parameters affecting the performances. Force application and displacement measurement are done in a noncontact manner, in order not to disturb operation: electromagnetic force is applied to the rotor and gap sensors are used to measure the displacement of the rotor. Experimental results show that repeatable runout decreases as speed, groove depth and clearance decrease. Nonrepeatable runout decreases as clearance decreases, and it has a minimum value at $5.5{\mu}m$ of grove depth and a maximum value at speed of 18.000rpm. Stiffness increases as speed increases and clearance decreases, and has a maximum value around $5.5{\mu}m$ of groove depth. The relationship between force and displacement is linear for small displacement, but becomes nonlinear for large displacement. Supporting load is linearly proportional to the stiffness, and it is a maximum value around $4.75{\mu}m$ of clearance.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.4
• /
• pp.637-643
• /
• 2002

The objective of this study is to provide a simple methodology to find optimum processing conditions to fabricate sub-micron structured DVD-RAM substrates with superb optical and geometrical properties. It was fecund that the birefringence, which is regarded as one of the most important optical properties for an optical disk, was very sensitive to the mold wall temperature history. Also, the integrity of the replication, represented by the land-groove structure and the radial tilt were influenced by the mold temperature and the compression pressure. A set of optimum conditions were obtained by applying Design of Experiment and the objective functions composed of three different objectives.

• KSTLE International Journal
• /
• v.2 no.1
• /
• pp.46-54
• /
• 2001

The herringbone groove journal bearing (HGJB) has chevron type grooves on stationary or rotating member of the bearing so that they pump the lubricant inward the grooves when journal rotates. As a result, the pressure is generated around the journal so that the radial stiffness and dynamic stability are improved comparing to the plain journal bearing (PJB) when the bearing operates near the concentric condition. The narrow groove theory, conventionally adopted to simulate the concentric operation of HGJB, is limited to the infinite number of grooves. A numerical study of air-lubricated HGJB is presented for the finite number of grooves. The compressible isothermal Reynolds equation is solved by using Finite Element Method together with the Newton-Raphson iterative procedure and perturbation method. The solutions render the static and dynamic performances of HGJB. Comparison of present results with a PJB validates previously published finite difference solution. The HGJB's geometric parameters influence its static and dynamic characteristics. The optimum geometric parameters are presented for the air-lubricated HGJB in particular conditions.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.11
• /
• pp.2664-2675
• /
• 1993

In this paper, the effects of chip breaker configuration on cutting forces for various cutting conditions are investigated and a method for predicting cutting forces effectively for chip breaker insert in milling is described. Based on the shear plane model and the relevant equations already existing for the relation among the parameters, the method makes use of the analytic geometric approach considering the configuration of cutting too by a 3-dimensional coordinate transformation matrix. The groove type chip breaker insert is modeled to be a double rake insert, represented by the first radial rake angle, the second radial rake angle and the length of land, and the program analyzing the cutting forces is developed. The program capability is verified by comparing the results with the experimental ones for a single cutter; and in case of primary cutting forces, the results of simulation and experiments agree very well showing 2%~16.7% difference within the feed rate range investigated.