• 대한기계학회논문집B
• /
• 제22권3호
• /
• pp.280-293
• /
• 1998

Numerical study on turbulent and mean structures of a turbulent boundary layer with longitudinal and spanwise pressure gradient is carried out by using Reynolds-stress-model (RSM). The existence of pressure gradient in a turbulent boundary layer causes the skewing or divergence of rates of strain, which contributes to production of turbulent kinetic energy. Also, this augmentation of production due to extra rates of strain can increase the turbulent mixing and cause the anisotropy of turbulent intensities in the outer layer. This paper uses the Reynolds Stress Model to capture anisotropy of turbulent structures effectively and is devoted to compare the results computed by using RSM and the standard k-.epsilon. model with experimental data. It is concluded that the RSM can produce the more accurate predictions for capturing the anisotropy of turbulent structure than the standard k-.epsilon. model.

• 한국연소학회지
• /
• 제7권2호
• /
• pp.49-61
• /
• 2002

Numerical simulation is performed for stagnating turbulent flows of impinging and countercurrent jets by the Reynolds stress model(RSM). Results are compared with those of the ${\kappa}-{\varepsilon}$ model and available data to assess the flow characteristics and turbulence modes. Three variants of the RSM tested are those of Gibson and Launder(GL), Craft and Launder(GL-CL) and Speziale, Sarkar and Gatski(SSG). As well known, the ${\kappa}-{\varepsilon}$ model overestimates turbulent kinetic energy near the wall significantly. Although the RSM is superior to the ${\kappa}-{\varepsilon}$ model, it shows considerable difference according to how the redistributive pressure-strain term is modeled. Results of the RSM for countercurrent jets are improved with the modified coefficients for the dissipation rate, $C_{{\varepsilon}1}\;and\;C_{{\varepsilon}2}$ suggested by Champion and Libby. The performance of the three variants of the RSM model for stagnating flows are assessed.

• 한국화재소방학회논문지
• /
• 제28권4호
• /
• pp.35-43
• /
• 2014

3개의 난류모델과 3개의 연소모델로 구성된 9개의 모델조합을 이용하여 난류 부분예혼합 제트화염 구조에 대한 수치적 예측성능을 검토하였다. 이용된 난류모델은 표준 ${\kappa}-{\varepsilon}$ 모델(SKE), Realizable ${\kappa}-{\varepsilon}$ 모델(RKE) 및 Reynolds 응력모델(RSM)이며 연소모델들은 Eddy Dissipation Concept 모델(EDC), Steady Laminar Flamelet 모델(SLF)와 Unsteady Laminar Flamelet 모델(ULF)이다. 9개 모델조합의 예측성능을 평가하기 위하여 실험결과가 알려진 Sandia D 화염인 난류 부분예혼합 제트화염을 대상으로 수치계산을 수행하였다. 얻어진 결과로서, 화염길이의 예측은 RSM > SKE > RKE순으로 길게 예측하였으며, RKE 난류모델은 화염길이를 너무 과소 예측하는 것을 확인하였다. RSM + SLF과 RSM + ULF의 조합은 화염길이는 비교적 잘 예측하였지만 하류에서의 화염온도를 과대 예측하였다. 반면에 SKE와 연소모델의 조합에서 SLF 또는 ULF 조합은 화염길이 뿐만 아니라 하류에서의 화염온도도 비교적 잘 예측하였는 것을 확인하였다. 반경방향 화염온도 및 화학종 농도분포를 비교해 본 결과 SKE와 연소모델의 조합이 가장 예측성능이 뛰어났으며 SKE + ULF의 조합이 가장 우수한 예측성능을 갖는 것을 확인하였다.

• 대한기계학회논문집B
• /
• 제21권7호
• /
• pp.911-918
• /
• 1997

The turbulent viscous wake flows behind a single airfoil, two-dimensional stationary blade row and three-dimensional rotating blade row were calculated, and the numerical results were compared with experimental ones. The numerical technique was based on the SIMPLE algorithm using three turbulent closure models, standard k-.epsilon. model(WFM), low Reynolds number k-.epsilon. model(LRN) and Reynolds stress model (RSM). In the case of a single airfoil, WFM, LRN and RSM presented fairly good velocity distributions in the wake compared with experimental data. In the case of the stationary blade row, LRN and RSM presented better results than WFM for wake velocity distribution, and especially LRN showed best results among these three turbulent models. In the case of the rotating blade row, WFM and LRN showed fairly good agreement with experimental data of the three-dimensional velocity component distributions in the range from hub to mid span region. LRN was also superior to WFM in accuracy of prediction for the wake velocity distribution as same with the cases of a airfoil and the stationary blade row.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집B
• /
• pp.485-490
• /
• 2000

The effect of curvature, rotation, variable cross-section can make very complex flow pattern in turbo-machinery such as Pumps, compressors, turbines, In this study of turbulent flow characteristics rotating $90^{\circ}$ curved duct under a Plane rate of strain condition is computationally analyzed. The objective of this study is to understand the complex turbulent flow phenomena in turbo-machinery passage by analyzing the modeled rotating $90^{\circ}$ curved duct flow. RSM(Reynolds Stress Model) was employed for the turbulence modeling of Reynolds stress in momentum equations proposed by Shin(1995). The three dimensional computational code which adopts RSM for trubulence modeling was newly developed for the generalized curvilinear coordinate.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집B
• /
• pp.473-478
• /
• 2000

In this study, the characteristics of the three-dimensional turbulent flow in a rotating square sectioned $90^{\circ}$ bend were investigated by numerical simulation and experiment. In the experimental study, the characteristics of a developing turbulent flow are measured using hot-wire anemometer to seize the rotational effects on the flow characteristics and to compare the results of computational simulation with Reynolds stress model. Each refinement is shown to lead to an appreciable improvement in the agreement between measurement and computation.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2001년도 추계 학술대회논문집
• /
• pp.44-50
• /
• 2001

A numerical study was made to choose the better turbulence model for the flow in the discharge flow path from a diffuser to a wall. In this study standard $\kappa-\epsilon$ model(SKE), RNG $\kappa-\epsilon$ model(RNG), and Reynolds stress model(RSM) were applied. In case of the flow with relatively high Reynolds number at a diffuser inlet, the pressure loss coefficients by RNG have a tendency to be near to those by SKE at small ratio(below about 0.35) of $h/D_o$, but to those by RSM at large ratio(above about 0.35). At large ratio RNG begins to enlarge the effects of rapid strain and streamline curvature. RNG & RSM are recommended as the appropriate turbulence models for this case. But it is noticeable that the velocity gradient pattern in RNG is same as in SKE, and also that the total pressure distribution in RNG is same as in RSM only at swirling flow area, same as in SKE only at main flow area.

• Wind and Structures
• /
• 제5권2_3_4호
• /
• pp.337-346
• /
• 2002

Wind tunnel pressure measurements and numerical simulations based on the Reynolds Stress Model (RSM) are compared with full and model scale data in the flow area of impingement, separation and wake for $60^{\circ}$ and $90^{\circ}$ wind azimuth angles. The phase averaged fluctuating pressures simulated by the RSM model are combined with modelling of the small scale, random pressure field to produce the total, instantaneous pressures. Time averaged, rsm and peak pressure coefficients are consequently calculated. This numerical approach predicts slightly better the pressure field on the roof of the TTU (Texas Tech University) building when compared to the wind tunnel experimental results. However, it shows a deviation from both experimental data sets in the impingement and wake regions. The limitations of the RSM model in resolving the intermittent flow field associated with the corner vortex formation are discussed. Also, correlations between the largest roof suctions and the corner vortex "switching phenomena" are observed. It is inferred that the intermittency and short duration of this vortex switching might be related to both the wind tunnel and numerical simulation under-prediction of the peak roof suctions for oblique wind directions.

• Journal of Mechanical Science and Technology
• /
• 제14권1호
• /
• pp.93-102
• /
• 2000

The objective of the present study is to investigate the pressure-strain correlation terms of the Reynolds stress models for the three dimensional turbulent boundary layer in a $30^{\circ}$ bend tunnel. The numerical results obtained by models of Launder, Reece and Rodi (LRR) , Fu and Speziale, Sarkar and Gatski (SSG) for the pressure-strain correlation terms are compared against experimental data and the calculated results from the standard k-${\varepsilon}$ model. The governing equations are discretized by the finite volume method and SIMPLE algorithm is used to calculate the pressure field. The results show that the models of LRR and SSG predict the anisotropy of turbulent structure better than the standard k-${\varepsilon}$ model. Also, the results obtained from the LRR and SSG models are in better agreement with the experimental data than those of the Fu and standard k-${\varepsilon}$ models with regard to turbulent normal stresses. Nevertheless, LRR and SSG models do not effectively predict pressure-strain redistribution terms in the inner layer because the pressure-strain terms are based on the locally homogeneous approximation. Therefore, to give better predictions of the pressure-strain terms, non-local effects should be considered.

• 한국안전학회지
• /
• 제11권3호
• /
• pp.66-74
• /
• 1996

Numerical simulations were carried out using standard Reynolds stress turbulence model(LRR model) and modified RSM(Janicka model ) to validate these models in combustion flow fields. Two flames were selected for use as a benchmark data for model testing. One is a conventional jet diffusion flame that has the effect of suppression of turbulence by combustion. The other is a triple jet diffusion flame that designed to give high turbulence to the periphery of the flame and to remove the low Reynolds-number flow fields. As a result, it was found that the modification of standard RSM model is indispensable in the modelling of flames with low turbulence region. And it is also necessary to improve the existing modified models for the universal use.