• Geomechanics and Engineering
• /
• v.33 no.1
• /
• pp.53-63
• /
• 2023

Rock disturbance caused by blasting and stress relaxation is commonly observed during excavation. As the distance from the source of disturbance increases, the degree of disturbance decreases, and rock at a large depth does not experience disturbance. However, in stability analyses, a single value of disturbance is often applied to the entire rock mass, which leads to underestimated results. In this study, this modeling mistake is addressed by considering realistically varying rock disturbance. The safety of infinite slopes in a disturbed rock mass with a strength governed by the Hoek-Brown failure criterion is investigated based on the kinematic approach of limit analysis. The maximum disturbance is assigned to the outermost slope face because it is directly exposed to blasting damage and dilation, and the disturbance progressively decays with distance in the rock mass. The safety analysis results indicate that the assumption of uniform disturbance in the entire rock mass leads to underestimation of the rock strength and safety on infinite rock slopes. A critical slip surface appears to be within the disturbed rock layer as well as the interface between the disturbed upper rock and undisturbed lower rock.

• Journal of The Geomorphological Association of Korea
• /
• v.28 no.1
• /
• pp.1-12
• /
• 2021

This study tried to reveal relative surface denudation resistance and ranking by geologic types in the Southern Korean Peninsula using an 1:250,000 digital geologic map and ASTER GDEM. Among rock types such as igneous, sedimentary and metamorphic rocks, metamorphic rock showed the greatest resistance to surface denudation. The most resistant rock to surface denudation by geologic periods (e.g., the Precambrian, Paleozoic, Mesozoic and Cenozoic) was found from the Precambrian. Among the major tectonic settings in the Southern Korean Peninsula such as the Gyeonggi massif, Okcheon belt, Yeongnam massif, Gyeongsang basin and Pohang basin, the Okcheon belt indicated the greatest resistance. The most and least resistant rocks from the representative nine rocks in the Southern Korean Peninsula were Paleozoic limestone, and Cretaceous sedimentary rock and Cenozoic sedimentary rock, respectively. This study suggests that Paleozoic limestone, Cretaceous volcanic rock, Paleozoic sedimentary rock and Precambrian gneiss can be regarded as hard rocks with high elevation, steep slope and complicated relief, while soft rocks with low elevation, gentle slope and simple relief are Jurassic granite, Cretaceous sedimentary rock and Cenozoic sedimentary rock.

• Journal of The Geomorphological Association of Korea
• /
• v.23 no.1
• /
• pp.1-16
• /
• 2016

This study estimates relationships between physical and chemical weathering indices of various rock types and topographical relief. Physical weathering properties such as rock strength and joint and chemical weathering indices such as the $SiO_2/Al2O_3$, CIA and WPI were analyzed from 18 rock outcrops in mountain and valley areas consisting of 9 rock types. The results indicate that the elevation and relief of topography increase physical strength of rock increases. It can be suggested that the total r(rock-mass strength rating) and R(rock rebound strength by Schmidt Hammer) are most useful indices as a quantitative weathering property factor to explain formative causes of topographical relief. The results also suggest that rock types such as sandstone, granite, gneiss and schist are most suitable to explain meaningful difference in topographical relief with the physical and chemical weathering indices.

• Geomechanics and Engineering
• /
• v.21 no.1
• /
• pp.11-21
• /
• 2020

The traditional formulations for estimation of bearing capacity in rock mechanics assume a homogeneous and isotropic rock mass. However, it is common that the rock mass consists of different layers of different rock properties or of the same rock matrix with distinct geotechnical quality levels. The bearing capacity of a heterogeneous rock is estimated traditionally through the weighted average. In this paper, the solution of the weighted average is compared to the finite difference method applied to a bilayer rock mass. The influence of different parameters such as the thickness of the layers, the rock type, the uniaxial compressive strength and the overall geotechnical quality of the rock mass on the bearing capacity of a bilayer rock mass is analyzed. A parametric study by finite difference method is carried out to develop a bearing capacity factor in function of the layer thickness and the rock mass quality expressed in terms of the geological strength index, which is presented in a form of a chart. Therefore, this correlation factor allows estimating the bearing capacity of a rock mass that is formed by two layers with distinct GSI, depending on the bearing capacity of the rock mass formed only by the upper layer and considered by that way as homogenous and isotropic rock mass.

• Journal of fish pathology
• /
• v.34 no.1
• /
• pp.9-15
• /
• 2021

Rock bream (Oplegnathus fasciatus) is a highly valued aquaculture species in Korea. However, the aquaculture industry suffers huge economic losses due to rock bream iridovirus (RBIV) infection in summer. The objective of this study was to determine genetic diversity and relationships of DNAs isolated from two groups of rock bream after RBIV infection using five microsatellite (MS) markers. The first group of fish died early and the second group of fish died later after RBIV infection. In this experiment, 90 fish (5.1±1.0 cm and 4.1±1.3 g) were injected with 50 μl of RBIV (10⁴ TCID⁵⁰/ml) and maintained at 26℃ for 15 days. Genomic DNAs were extracted from fins of 20 fish that died earlier or later after RBIV infection. These DNAs were subjected to genotyping using five MS markers (CA-03, CA3-05, CA3-06, CA-10, and CA3-36). Of these markers, CA3-05 (early death group), CA3-06 (late death group), and CA3-36 (both early and late death groups) showed different alleles distribution rates. In-depth studies are needed to provide valuable information for selecting RBIV-resistant fish. In conclusion, microsatellite marker distribution pattern differences between early- and late- death groups of rock bream after RBIV infection showing different RBIV susceptibilities were determined using MS markers and genotyping. Results of this study suggest that MS markers could be used to facilitate the selection of RBIV resistant rock bream.

• Explosives and Blasting
• /
• v.16 no.2
• /
• pp.23-33
• /
• 1998

This study has been carried out to design the standards of rock bolts which are recommended to be used for supporting material in Seong Ju tunnel, Under recently planned to construct. Due to the weak bedding rocks along the Tunnel, NATM supporting method is assumed to be applied and the design and calculation for rock bolts which are important material for this supporting method. Though the study, the results obtained are as follows. 1) The rocks defined s coarse sandstone, fine sandstone, medium sandstone, sandy shale and silty shale are normal rocks in strength, and black shale, greywacke and conglomerate are weak rocks in strength. 2) When the length of 3∼4meters of rock bolts are used, the distances of bolts are supposed to be 1.3∼1.8m in sandstone and 1.3∼2.0m in shale and for greywacke the distance should be 1.5m.

• Tunnel and Underground Space
• /
• v.7 no.1
• /
• pp.1-12
• /
• 1997

Engineering rock mass classification is extensively used to determine the reasonable support system throughout the tunneling process in the field. Selection of support system based on the results of engineering rock mass classification is simple and straight-forward. However, this method cannot consider the effect of in-situ stresses, mechanical properties of support material, and support installation time on the behavior or rock-support system To handle the various conditions encountered in the underground excavation sites rock-support system. To handle the various conditions encountered in th eunderground excavation sites rock-support interaction program has been developed. This program can analyze the interaction between rock mass and support materials and also can simulate the tunnel excavation-support insstallation process by controlling the support installation time and the stiffness of support system. Practical applicability of this program was verfied by comparing the results of support design to those from rock mass classification for virtual underground excavation at the drilling site KD-06 in Geoje island.

• Tunnel and Underground Space
• /
• v.5 no.4
• /
• pp.336-346
• /
• 1995

Geotechnical Information System (GTIS) for efficient management of three dimensional borehole data has been developed. Some problems were raised during the input process of borehole data, and alternative solutions were sought. According to the previous geotechnical reports, there is no unified weathering classification scheme. A criterion, 100 times/30cm from SPT, was turned out inappropriate to the discrimination of weathered rock from weathered soil. It has also been suggested that weathered soil, weathered rock, soft rock, and hard rock should be defined as CW, HW, MW, and SW~fresh condition. For better comparison of RQD, the use of NX size coring is recommended for the whole area although BX size coring has been used in excavated area. The limit of drilling depth up to 1 m from the top of surface of hard rock should be extended to avoid possible wrong interpretation of rock head due to the existence of corestone. The input data were analysed by geostatistical methods. It is found that the range in semivariogram is about 300m, and the variance of gneiss is greater than that of granite. It is because the granite data analysed came from almost single uniform rock mass(i.e.Seoul granite), but gneiss data came from the rock mass(i.e. Gyeonggi gneiss complex experienced several metamorphic metamorphic processes.

• Journal of fish pathology
• /
• v.32 no.1
• /
• pp.1-8
• /
• 2019

Rock bream iridovirus (RBIV) is a member of the Megalocytivirus genus that causes severe mortality to rock bream (Oplegnathus fasciatus) with characteristic clinical signs of spleen enlargement. In this study, we assessed spleen size and RBIV copy number patterns in RBIV-infected rock bream to determine lethal and safe levels of virus copy number/spleen index that may define disease progress. We found that rock bream infected with RBIV ($1.1{\times}10^7virus\;copy\;number/100{\mu}l$) and held at 29, 26, 23 or $20^{\circ}C$ exhibited significantly higher levels of spleen size compared to $17^{\circ}C$. In dead condition (100% mortality at $20{\sim}29^{\circ}C$), the spleen index ($spleen\;weight/fish\;weight{\times}100$) and virus copy number were 3.00~5.38 and $10^6{\sim}10^8/{\mu}l$, respectively. Conversely, in survived condition (0% mortality at $17^{\circ}C$), spleen index and virus copy number was as low as not-infected control ($0.34{\sim}1.22/10^0{\sim}10^1/{\mu}l$, respectively). These findings suggest that spleen index can be an indicator of disease severity of RBIV disease.

• Tunnel and Underground Space
• /
• v.16 no.1 s.60
• /
• pp.1-10
• /
• 2006

Rock masses in nature include various rock discontinuities such as faults, joints, bedding planes, fractures, cracks, schistosities, and cleavages. The behavior of rock structures, therefore, is mainly controlled by various rock discontinuities. In many tunnels, enormous cost and time are consumed to cope with the failing or sliding of rock blocks, which cannot be predicted because of the complexity of rock discontinuities. It is difficult to estimate the properties of rock masses before the rock excavation. The observational design and construction method of tunnels in rock masses is becoming important recently. In this paper, a new observational design and construction method for rock block evaluation of tunnels in discontinuous rock masses is proposed, and then applied to the tunnel based on actual rock discontinuity information observed in the field. It is possible to detect key blocks all along the tunnel exactly by using the numerical analysis program developed far the new observational design and construction method. This computer simulation method with user-friendly interfaces can calculate not only the stability of rock blocks but also the design of supplementary supports. The effectiveness of the proposed observational design and construction method has been verified by the confirmation of key block during the enlargement excavation.